UNI/TR 11481 : 2013
Current
The latest, up-to-date edition.
Usi del polietilene nelle linee dirette e nella distribuzione del gas combustibile - Tecnologie riconosciute e applicabili - Linee guida di orientamento per gli operatori
03-07-2013
1 SCOPO E CAMPO DI APPLICAZIONE
2 RIFERIMENTI NORMATIVI
3 TERMINI E DEFINIZIONI
4 RACCOMANDAZIONI
5 RACCOMANDAZIONI DI NATURA GESTIONALE
APPENDICE A (informativa) - CORRISPONDENZA TRA I
PUNTI DEL PRESENTE RAPPORTO TECNICO
E I PUNTI DI NORME TECNICHE, ARTICOLI
DELL'ALLEGATO "A" DELLA DELIBERA
DELL'AUTORITA PER L'ENERGIA ELETTRICA
E IL GAS, ARG/GAS 120/08
APPENDICE B (informativa) - SIGNIFICATO E FUNZIONI DEI
CARATTERI NUMERICI UTILIZZATI NELLA
COMPOSIZIONE DEL CODICE A BARRE DEDICATO
ALLA SALDATURA DEI RACCORDI ELETTROSALDABILI
APPENDICE C (informativa) - SCHEMA ESEMPLICATIVO PER LA
POSA E IL CABLAGGIO DEL CAVO PILOTA
UTILIZZABILE PER LA LOCALIZZAZIONE
APPENDICE D (informativa) - CARATTERISTICHE TECNICHE
COSTRUTTIVE E PRESTAZIONALI DELLE
APPARECCHIATURE SCHIACCIATUBI
APPENDICE E (informativa) - ESEMPIO DI DIAGRAMMA DI FLUSSO
RELATIVO AD UN PROCESSO DI LAVORAZIONE
CHE PERMETTE LA RACCOLTA DATI PER IL SISTEMA GIS
APPENDICE F (informativa) - TECNOLOGIE NO-DIG (TRENCHLESS)
APPENDICE G (informativa) - L'INTEGRAZIONE DEL SISTEMA
POLIETILENE NEL GIS
BIBLIOGRAFIA
This technical report provides informations and guidelines for operators involved in design, construction, test and maintenance of gas polyethylene networks, for gases of 1st, 2nd, 3rd family, with 5 bar MOP.
| Committee |
CT 100
|
| DocumentType |
Technical Report
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Current
|
| UNI CEI EN ISO/IEC 17050-1 : 2010 | CONFORMITY ASSESSMENT - SUPPLIER'S DECLARATION OF CONFORMITY - PART 1: GENERAL REQUIREMENTS |
| ISO 12176-3:2011 | Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 3: Operator's badge |
| UNI EN 12106 : 1999 | PLASTICS PIPING SYSTEMS - POLYETHYLENE (PE) PIPES - TEST METHOD FOR THE RESISTANCE TO INTERNAL PRESSURE AFTER APPLICATION OF SQUEEZE-OFF |
| UNI EN ISO 9000 : 2005 | QUALITY MANAGEMENT SYSTEMS - FUNDAMENTALS AND VOCABULARY |
| CEI 64-8/7 : 2012 | LOW VOLTAGE ELECTRICAL INSTALLATIONS - PART 7: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS |
| ISO 10838-3:2001 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| UNI 10576 : 1996 | GAS PIPELINES PROTECTION DURING UNDERGROUND WORKS |
| UNI EN ISO 9001 : 2008 | QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS |
| UNI EN 1775 : 2007 | GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| ISO 12176-4:2003 | Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 4: Traceability coding |
| ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| UNI 9860 : 2006 | GAS SERVICE PIPES - DESIGN, CONSTRUCTION, TESTING, OPERATION, MAINTENANCE AND REHABILITATION |
| UNI 9737 : 2007 | QUALIFICATION OF WELDERS OF PLASTICS: WELDERS OF POLYETHYLENE COMPONENTS AND/OR POLYPROPYLENE, FOR THE CONVEYANCE OF COMBUSTIBLE GASES, WATER AND/OR OTHER FLUIDS UNDER PRESSURE, USING THE PROCEDURES FOR CONTACT HEATING ELEMENTS AND ELECTROFUSION - COMPLEMENTARY INSTRUCTIONS FOR THE APPLICATION OF EN 13067 |
| UNI 10967 : 2001 | WELDING OF POLYETHYLENE PE 100 PIPES AND CONNECTIONS FOR GAS, WATER AND OTHER PRESSURE FLUIDS PIPELINES |
| UNI/TR 11228 : 2007 | PROTECTING STRUCTURES FOR BURIED GAS PIPES FOR INTERFERENCES WITH RAILWAYS, TRAMWAYS, ROADS, OTHER BURIED UTILITIES AND BUILDINGS |
| UNI 10521 : 2012 | WELDING OF PLASTIC MATERIALS - ELECTRO-FUSION WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES |
| UNI 7131 : 2014 | LPG PLANTS FOR DOMESTIC USE NOT FED BY A DISTRIBUTION NETWORK - DESIGN, INSTALLATION AND COMMISSIONING |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 11414:2009 | Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| UNI EN 1555-2 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| UNI EN 12007-1 : 2012 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 1: GENERAL FUNCTIONAL REQUIREMENTS |
| UNI EN 1555-3 : 2013 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS |
| UNI EN 12007-2 : 2012 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL REQUIREMENTS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| UNI EN 1555-1 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| UNI 11024 : 2003 | QUALITY REQUIREMENTS FOR WELDING OF POLYETHYLENE PIPES FOR GAS, WATER AND OTHER PRESSURE FLUIDS PIPELINES |
| UNI 10761 : 2012 | COORDINATION OF WELDING, PIPE LAYING AND TEST ACTIVITIES FOR POLYETHYLENE TRANSMISSION LINES OF GASEOUS FUELS, WATER AND OTHER FLUIDS UNDER PRESSURE - TASKS AND RESPONSIBILITIES, REQUIREMENTS FOR TRAINING, QUALIFICATION AND CERTIFICATION OF PERSONNEL |
| UNI 10520 : 2009 | WELDING OF PLASTIC MATERIALS - HEATED TOOL BUTT WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES |
| PREN ISO 11299-3 : DRAFT 2012 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11299-3:2011) |
| UNI EN 10204 : 2005 | METALLIC PRODUCTS - TYPES OF INSPECTION DOCUMENTS |
| PREN ISO 11299-1 : DRAFT 2012 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 1: GENERAL (ISO 11299-1:2011) |
| ISO 16241:2005 | Notch tensile test to measure the resistance to slow crack growth of polyethylene materials for pipe and fitting products (PENT) |
| UNI 9165 : 2004 | GAS DISTRIBUTION NETWORKS - PIPEWORKS WITH MAXIMUM OPERATING PRESSURE UP TO 5 BAR - DESIGN, CONSTRUCTION, TESTING, OPERATION, MAINTENANCE AND REHABILITATION |
| UNI EN 1555-5 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM |
| UNI CEI EN ISO/IEC 17050-2 : 2005 | CONFORMITY ASSESSMENT - SUPPLIER'S DECLARATION OF CONFORMITY - PART 2: SUPPORTING DOCUMENTATION |
| UNI EN 12007-4 : 2012 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 4: SPECIFIC FUNCTIONAL REQUIREMENTS FOR RENOVATION |
| UNI 10565 : 2008 | FIELD WELDING MACHINES BY THE HEATED TOOL FOR POLYETHYLENE PIPES AND/OR FITTINGS BUTT JOINTS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES - CONSTRUCTION, TEST AND MAINTENANCE REQUIREMENTS, DOCUMENTATION |
| ISO 13950:2007 | Plastics pipes and fittings Automatic recognition systems for electrofusion joints |
| UNI 10566 : 2013 | ELECTROFUSION WELDING MACHINES AND AUXILIARY EQUIPMENT FOR POLYETHYLENE PIPES AND/OR FITTING JOINTS BY ELECTROWELDABLE CONNECTIONS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES CONSTRUCTION, TEST AND MAINTENANCE REQUIREMENTS, DOCUMENTATION |
| ISO 11413:2008 | Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
| UNI EN 12327 : 2012 | GAS INFRASTRUCTURE - PRESSURE TESTING, COMMISSIONING AND DECOMMISSIONING PROCEDURES - FUNCTIONAL REQUIREMENTS |
| UNI 9034 : 2004 | GAS DISTRIBUTION PIPELINES WITH MAXIMUM OPERATING PRESSURE NOT EXCEEDING 0,5 MPA (5 BAR) - MATERIALS AND JOINING SYSTEMS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.