UNI EN ISO 21809-1 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 1: POLYOLEFIN COATINGS (3-LAYER PE AND 3-LAYER PP)
09-08-2022
01-01-2011
Foreword
Introduction
1 Scope
2 Conformance
3 Normative references
4 Terms and definitions
5 Symbols and abbreviated terms
6 Information supplied by the purchaser
7 Coating classification
8 Coating materials
9 Coating system qualification
10 Application of the coating system
11 Inspection and testing
12 Coating repairs
13 Marking
14 Handling and storage in the applicators facilities
15 Test reports and certificate of compliance
Annex A (normative) - Inspection of thickness
Annex B (normative) - Holiday detection test
Annex C (normative) - Peel strength test
Annex D (normative) - Thermal analysis of epoxy and cured
epoxy coating film
Annex E (normative) - Impact test
Annex F (normative) - Indentation test
Annex G (normative) - UV ageing test and thermal ageing
test
Annex H (normative) - Cathodic disbondment test
Annex I (normative) - Flexibility test
Annex J (normative) - Gel time of the epoxy powder
Annex K (normative) - Total volatile/moisture content of
the epoxy powder - Mass loss
Annex L (normative) - Procedure qualification trial,
inspection and testing plan and daily log
Annex M (normative) - Hot water immersion test
Annex N (normative) - Density of epoxy powder
Bibliography
Describes requirements of plant-applied external three-layer polyethylene- and polypropylene-based coatings for corrosion protection of welded and seamless steel pipes for pipeline transportation systems in the petroleum and natural gas industries in accordance with ISO 13623.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 21809-1:2011 | Identical |
| ISO 21809-1:2011 | Identical |
| ISO 8502-3:2017 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) |
| AS 3894.6-2002 | Site testing of protective coatings Determination of residual contaminants (Reconfirmed 2013) |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO/TS 29001:2010 | Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations |
| ISO 1873-2:2007 | Plastics Polypropylene (PP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| ISO 8130-2:1992 | Coating powders Part 2: Determination of density by gas comparison pyknometer (referee method) |
| ISO 3183:2012 | Petroleum and natural gas industries Steel pipe for pipeline transportation systems |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| SSPC-AB 1 : 2015 | MINERAL AND SLAG ABRASIVES |
| ISO 14001:2015 | Environmental management systems — Requirements with guidance for use |
| ISO 1872-2:2007 | Plastics Polyethylene (PE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| SSPC-AB 2 : 2015 | CLEANLINESS OF RECYCLED FERROUS METALLIC ABRASIVES |
| ISO 15512:2016 | Plastics Determination of water content |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 3251:2008 | Paints, varnishes and plastics Determination of non-volatile-matter content |
| ISO 8502-6:2006 | Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 6: Extraction of soluble contaminants for analysis The Bresle method |
| ISO 8502-9:1998 | Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 9: Field method for the conductometric determination of water-soluble salts |
| ISO 8503-4:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Stylus instrument procedure |
| ISO 11127-6:2011 | Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 6: Determination of water-soluble contaminants by conductivity measurement |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 8503-5:2017 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determination of the surface profile |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| ISO 8130-3:1992 | Coating powders Part 3: Determination of density by liquid displacement pyknometer |
| ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.