UNI EN ISO 1133 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS
02-09-2012
01-01-2005
Foreword
1 Scope
2 Normative references
3 Apparatus
4 Test sample
5 Temperature calibration, cleaning and maintenance
of the apparatus
6 Procedure A
7 Procedure B
8 Flow rate ratio (FRR)
9 Precision
10 Test report
Annex A (normative) Test conditions for melt flow rate
determination
Annex B (informative) Conditions in use for the
designation of standards for thermoplastic
materials
Figure 1 - Typical apparatus for determining melt flow
rate (showing one of the possible methods of
retaining the die and one type of piston)
Table 1 - Maximum allowable variation in temperature
with distance and with time
Table 2
Table A.1
Table B.1
Provides two procedures for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastic materials under specified conditions of temperature and load.
| DevelopmentNote |
Supersedes UNI 5640. (07/2001)
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN ISO 1133 : 2005 | Identical |
| NS EN ISO 1133 : 2ED 2005 | Identical |
| DIN EN ISO 1133:2005-09 | Identical |
| I.S. EN ISO 1133:2005 | Identical |
| NF EN ISO 1133 : 2005 | Identical |
| SN EN ISO 1133 : 1999 CORR 2006 | Identical |
| BS EN ISO 1133:2005 | Identical |
| NBN EN ISO 1133 : 2005 COR 2006 | Identical |
| UNE-EN ISO 1133:2006 | Identical |
| ISO 1133:2005 | Identical |
| EN ISO 1133:2005 | Identical |
| DIN EN ISO 1133:2000-02 | Identical |
| UNI 11434 : 2012 | STEEL REINFORCED SPIRALLY FORMED POLYETHYLENE PIPES FOR NON PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE |
| UNI 10667-10 : 2011 | PLASTIC RAW-SECONDARY MATERIALS - POLYSTYRENE FOR GENERAL PURPOSES, FROM THE RECYCLING OF INDUSTRIAL RESIDUES AND/OR FROM PRE AND/OR POST-CONSUMER MATERIALS - PART 10: REQUIREMENTS AND TEST METHODS |
| UNI 10667-11 : 2009 | RECYCLED PLASTIC MATERIALS - POLYETHYLENE AND ETHYLENE COPOLYMERS FROM AGRICULTURAL AND HORTICULTURAL FILMS TO BE USED FOR DIFFERENT PURPOSES - REQUIREMENTS AND TEST METHODS |
| UNI 10667-2 : 2010 | PLASTIC RAW-SECONDARY MATERIALS - POLYETHYLENE FOR GENERAL PURPOSES FROM THE RECYCLING OF INDUSTRIAL RESIDUES AND/OR FROM PRE AND/OR POST CONSUMER MATERIALS - PART 2: REQUIREMENTS AND TEST METHODS |
| UNI 11329 : 2009 | FOOD PACKAGING - REQUIREMENTS FOR CLOSURES OF PRIMARY PET PACKAGING INTENDED TO CONTAIN DRINKS AND FOODSTUFFS |
| UNI 10667-3 : 2011 | PLASTIC RAW-SECONDARY MATERIALS - POLYPROPYLENE FOR GENERAL PURPOSES FROM THE RECYCLING OF INDUSTRIAL RESIDUES AND/OR FROM PRE AND/OR POST CONSUMER MATERIALS - PART 3: REQUIREMENTS AND TEST METHODS |
| UNI/TS 11344 : 2009 | METALLO-PLASTIC MULTILAYER PIPING SYSTEMS AND FITTINGS FOR INDOOR INSTALLATION FOR THE CONVEYANCE OF GASEOUS FUELS |
| UNI 10954-1 : 2008 | METALLO-PLASTIC MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER - PART 1: PIPES |
| UNI 11342 : 2009 | COPPER AND COPPER ALLOYS - COMPOSITE, SEAMLESS COPPER-PE, TUBES FOR FLUID DISTRIBUTION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.