UNI EN 1870-4 : 2012
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
Superseded date
08-13-2022
Superseded by
Published date
01-01-2012
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (normative) - Dimensional tolerances
of saw spindles
Annex B (normative) - Braking tests
Annex C (normative) - Type test for
anti-splinter system
Annex D (normative) - Impact test method
for guards
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
Describes all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to multi-blade rip sawing machines as defined, herein after referred to as "machines", designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic edging and/or plastic/light alloy laminates.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 1870-4:2012 | Identical |
| NBN EN 1870-4 : 2012 | Identical |
| NEN EN 1870-4 : 2012 | Identical |
| SN EN 1870-4 : 2012 | Identical |
| NF EN 1870-4 : 2012 | Identical |
| UNE-EN 1870-4:2012 | Identical |
| NS EN 1870-4 : 2012 | Identical |
| EN 1870-4:2012 | Identical |
| DIN EN 1870-4:2012-06 | Identical |
| I.S. EN 1870-4:2012 | Identical |
| EN 1005-4:2005+A1:2008 | Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN ISO 2286-2:2016 | Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate (ISO 2286-2:2016) |
| ISO 7211-2:1984 | Textiles — Woven fabrics — Construction — Methods of analysis — Part 2: Determination of number of threads per unit length |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN ISO 1421:2016 | Rubber- or plastics-coated fabrics - Determination of tensile strength and elongation at break (ISO 1421:2016) |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 61800-5-2:2017 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| EN ISO 14163:1998 | Acoustics - Guidelines for noise control by silencers (ISO 14163:1998) |
| EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
| EN 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN ISO 3743-2:2009 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) |
| HD 221 : 200S1 | RUBBER INSULATED CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V - GENERAL REQUIREMENTS |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| EN 61508-7:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures |
| ISO 7960:1995 | Airborne noise emitted by machine tools Operating conditions for woodworking machines |
| EN ISO 2060:1995 | Textiles - Yarn from packages - Determination of linear density (mass per unit length) by the skein method (ISO 2060:1994) |
| EN 1093-9:1998+A1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 614-2:2000+A1:2008 | Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks |
| ISO 4649:2017 | Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device |
| EN 50370-2:2003 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1005-1:2001+A1:2008 | Safety of machinery - Human physical performance - Part 1: Terms and definitions |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| EN 12779:2015 | Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| EN 50178:1997 | Electronic equipment for use in power installations |
| HD 21.1 : 200S4 | CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOPLASTIC INSULATION - GENERAL REQUIREMENTS |
| ISO 2286-2:2016 | Rubber- or plastics-coated fabrics Determination of roll characteristics Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate |
| EN 61508-2:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 61496-1:2013/AC:2015 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012) |
| EN 60947-4-1 : 2010 AMD 1 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| ISO 2060:1994 | Textiles — Yarn from packages — Determination of linear density (mass per unit length) by the skein method |
| IEC 60439-1:1999+AMD1:2004 CSV | Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 14163:1998 | Acoustics — Guidelines for noise control by silencers |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| EN 847-1:2017 | Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN 1049-2:1993 | Textiles - Woven fabrics - Construction - Methods of analysis - Part 2: Determination of number of threads per unit length (ISO 7211-2:1984 modified) |
| ISO 1421:2016 | Rubber- or plastics-coated fabrics — Determination of tensile strength and elongation at break |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 1005-3:2002+A1:2008 | Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation |
| IEC 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN 50370-1:2005 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission |
| IEC 61508-7:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures (see Functional Safety and IEC 61508) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| IEC 61508-2:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508) |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| EN 1093-11:2001+A1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index |
| IEC 61800-5-2:2016 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.