UNI EN 12809 : 2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RESIDENTIAL INDEPENDENT BOILERS FIRED BY SOLID FUEL - NOMINAL HEAT OUTPUT UP TO 50 KW - REQUIREMENTS AND TEST METHODS
02-07-2019
01-01-2004
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Material, design and construction
5 Safety
6 Performance
7 Appliance instructions
8 Marking
9 Evaluation of conformity
Annex A (normative) - Test methods
Annex B (normative) - Test fuels and recommended fuels
Annex C (informative) - A-deviations
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction Products
Directive
Bibliography
Gives requirements relating to the design, manufacture, construction, performance (efficiency and emission), safety, instruction and marking together with associated test methods and test fuels for type testing residential independent boilers fired by solid fuels.
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN 12809 : 2006 | Identical |
| NBN EN 12809 : 2001 AMD 1/COR 07 | Identical |
| NS EN 12809 : 2001 AC 2007 | Identical |
| BS EN 12809 : 2001 | Identical |
| DIN EN 12809:2005-08 | Identical |
| NF EN 12809 : 2002 AMD 1 2005 | Identical |
| I.S. EN 12809:2001 | Identical |
| SN EN 12809 : 2001 AMD 1/CORR 07 | Identical |
| NEN EN 12809 : 2001 C1 2007 | Identical |
| UNE-EN 12809:2002 | Identical |
| UNI 10683 : 2012 | HEATING APPLIANCES FIRED BY WOOD OR OTHER SOLID BIOFUELS - INSTALLATION REQUIREMENTS |
| UNI/TS 11300-4 : 2012 | ENERGY PERFORMANCE OF BUILDINGS - PART 4: RENEWABLE ENERGY AND OTHER GENERATION SYSTEMS FOR SPACE HEATING AND DOMESTIC HOT WATER PRODUCTION |
| UNI 10412-2 : 2009 | HOT WATER HEATING SYSTEMS - SAFETY REQUIREMENTS - PART 2: REQUIREMENTS FOR SYSTEMS WITH RESIDENTIAL SOLID FUELS BURNING APPLIANCES WITH BOILER, NOT EXCEEDING A TOTAL NOMINAL HEAT OUTPUT OF 35 KW |
| EN 10120:2017 | Steel sheet and strip for welded gas cylinders |
| EN 50165 : 97 AMD 1 2001 | ELECTRICAL EQUIPMENT ON NON-ELECTRIC APPLIANCES FOR HOUSEHOLD AND SIMILAR PURPOSES - SAFETY REQUIREMENTS |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| ISO 1928:2009 | Solid mineral fuels Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value |
| ISO 334:2013 | Solid mineral fuels Determination of total sulfur Eschka method |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| ISO 7-2:2000 | Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| ISO 331:1983 | Coal Determination of moisture in the analysis sample Direct gravimetric method |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| ISO 687:2010 | Solid mineral fuels — Coke — Determination of moisture in the general analysis test sample |
| ISO 501:2012 | Hard coal — Determination of the crucible swelling number |
| ISO 228-2:1987 | Pipe threads where pressure-tight joints are not made on the threads Part 2: Verification by means of limit gauges |
| ISO 1171:2010 | Solid mineral fuels — Determination of ash |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 562:2010 | Hard coal and coke — Determination of volatile matter |
| EN 1561:2011 | Founding - Grey cast irons |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.