UNI EN 1020 : 2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
NON-DOMESTIC FORCED CONVECTION GAS- FIRED AIR HEATERS FOR SPACE HEATING NOT EXCEEDING A NET HEAT INPUT OF 300 KW INCORPORATING A FAN TO ASSIST TRANSPORTATION OF COMBUSTION AIR OR COMBUSTION PRODUCTS
05-12-2022
01-01-2009
Foreword
1 Scope
2 Normative references
3 Terms and definitions
3.1 Appliance and its constituent parts
4 Classification of systems
4.1 Classification according to the nature of the gases
used (Categories)
4.2 Classification of appliances according to the gases
capable of being used
4.3 Classification of appliances according to the mode
of evacuation of the combustion products
5 Constructional requirements
5.1 General
5.2 Adjusting, control and safety devices
5.3 Ignition devices
5.4 Transportation of combustion air and/or flue gases
5.5 Flame supervision system
5.6 Start-gas flame establishment
5.7 Main flame establishment
5.8 Main burner
5.9 Facility for remote control
5.10 Thermostats and air temperature control
5.11 Gas pressure test points
5.12 Combustion chamber pressure relief
5.13 Facilities for commissioning and testing
5.14 Additional requirements for appliances designed for
outdoor installation
6 Operational requirements
6.1 Safety of operation
6.2 Efficiency
7 Test methods
7.1 General
7.2 Construction and design
7.3 Safety of operation
7.4 Efficiency
8 Marking and instructions
8.1 Marking of the appliance
8.2 Marking of the packaging
8.3 Utilization of symbols on the appliance and packaging
8.4 Instructions
9 Evaluation of conformity of POCED's and their associated
terminals
9.1 General
9.2 Type testing
9.3 Factory production control (FPC)
Annex A (informative) - National situations
Annex B (informative) - Equivalence rules
Annex C (normative) - Classification according to the
evacuation of the combustion
Annex D (normative) - Requirements and test methods
for separate air supply and combustion products
evacuation ducts
Annex E (informative) - Facilities for commissioning and
testing
Annex F (informative) - Identification of gas types in use
in various countries
Annex G (informative) - Requirements in EN 1020 which
relate to the design and construction of forced draught
burners covered in EN 676:1996
Annex H (informative) - A-deviations
Annex I (normative) - Special national conditions
Annex J (informative) - National solutions for countries
whose national bodies are Affiliate
Members of CEN
Annex K (informative) - Calculation of conversions of NOx
Annex L (informative) - Sampling plan example
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU Directives
Annex ZB (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction Products
Directive
Bibliography
Describes the requirements and test methods for the safety and efficiency of non-domestic gas-fired air heaters having a fan to assist the transportation of combustion air and/or flue gases. Also covers appliances having forced draught burners.
| DevelopmentNote |
Together with UNI EN 525, UNI EN 621, UNI EN 778 and UNI EN 1319, it supersedes UNI 8124 and UNI 8125. (08/2001)
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN 1020 : 2009 | Identical |
| DIN EN 1020:2010-05 | Identical |
| NBN EN 1020 : 2010 | Identical |
| UNE-EN 1020:2010 | Identical |
| NS EN 1020 : 2009 | Identical |
| SN EN 1020 : 2010 | Identical |
| NF EN 1020 : 2010 | Identical |
| I.S. EN 1020:2009 | Identical |
| BS EN 1020:2009 | Identical |
| EN 1020:2009 | Identical |
| EN 1859:2009+A1:2013 | Chimneys - Metal chimneys - Test methods |
| IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV | Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ISO 6976:2016 | Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 60584-2:1993 | Thermocouples - Part 2: Tolerances |
| EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
| EN 12067-1 : 98 AMD 1 2003 | GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES |
| ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
| EN ISO 3166-1:2014 | Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013) |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN 125:2010+A1:2015 | Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 126:2012 | Multifunctional controls for gas burning appliances |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| EN 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| CR 1404:1994 | Determination of emissions from appliances burning gaseous fuels during type-testing |
| IEC 60730-2-1:1989 | Automatic electrical controls for household and similar use. Part 2: Particular requirements for electrical controls for electrical household appliances |
| EN 60335-2-102:2016 | Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| EN 60730-2-1 : 97 AMD 11 2005 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-1: PARTICULAR REQUIREMENTS FOR ELECTRICAL CONTROLS FOR ELECTRICAL HOUSEHOLD APPLIANCES |
| ISO 3166-1:2013 | Codes for the representation of names of countries and their subdivisions Part 1: Country codes |
| EN 61058-1:2002/A2:2008 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN ISO 6976:2016 | Natural gas - Calculation of calorific values, density, relative density and Wobbe indices from composition (ISO 6976:2016) |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| IEC 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| EN 88-1:2011+A1:2016 | Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN 257:2010 | Mechanical thermostats for gas-burning appliances |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.