SAEITC TS128-6
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
TS128 \"All Metal\" Self-Locking Nuts (UNJ Threads) 1100 MPa (160,000 lbf/in²) Minimum Tensile Strength at Room Temperature
Hardcopy , PDF
English
09-01-2006
11-22-2019
FOREWORD
1. SCOPE
2. ASSOCIATED DOCUMENTS
3. DEFINITIONS
4. QUALITY ASSURANCE
5. TEST EQUIPMENT
6. TECHNICAL REQUIREMENTS & TEST METHODS
APPENDIX 1 - TEST FIXTURES (INCLUDING HARDNESS TESTING)
APPENDIX 2 - VIBRATION TEST FIXTURE
APPENDIX 3 - PUSH-OUT TEST REQUIREMENTS
APPENDIX 4 - TORQUE-OUT TEST REQUIREMENTS
APPENDIX 5 - HARDNESS CHECKING FIXTURE
Covers the requirements for all metal, self-locking nuts, with threads to BS A 346 (ISO 3161) and is based on the American SAE specification AS 7251.
| DocumentType |
Standard
|
| Pages |
40
|
| PublisherName |
SAE Industry Technologies Consortia
|
| Status |
Superseded
|
| SupersededBy |
| MIL C 16173 : E | CORROSION PREVENTIVE COMPOUND, SOLVENT CUTBACK, COLD APPLICATION |
| BS A 346:2000 | UNJ threads. General requirements and limit dimensions |
| SAEITC TS21-11 | TS21 Manufacturing Specification for Bolts 900 MPa (130,000 lbf/in²) Tensile at Room Temperature |
| DEF 2331 : A AMD 3 | PROTECTIVE PX 1 DYED AND UNDYED |
| SAE AMS 7477 : B 70(R1982) | BOLTS AND SCREWS-STEEL-CORROSION AND HEAT RESISTANT, UPSET HEADED, HEAT TREATED, ROLL THREADED SOLUTION AND PRECIPITATION TREATED |
| ISO 2859:1974 | Sampling procedures and tables for inspection by attributes |
| DEFSTAN 91-98/2(2001) : 2001 | LUBRICATING OIL, GAS TURBINE ENGINE, SYNTHETIC GRADE 7.5 CST NATO CODE: O-149 JOINT SERVICE DESIGNATION: OX-38 |
| BS 4A 4-1.3:1967 | Specification for test pieces and test methods for metallic materials. Tensile tests Uninterrupted creep and rupture tests. Metric units |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| BS HR 650:1972 | Specification for high expansion heat-resisting steel bar and wire for the manufacture of bolts, studs, set screws and nuts (Ni 25.5, Cr 15, Ti 2, Mn 1.5, Mo 1.25, Si 0.7, V 0.3) (limiting ruling section 20 mm) |
| SAE AS954F | Wrenches, Hand, Twelve Point, High Strength, Thin Wall |
| BS 1134-2:1990 | Assessment of surface texture. Guidance and general information |
| SAEITC TS48-4 | TS48 Technical Specification for the Performance of Sockets and Ring Spanners |
| SAE AMS2411H | Plating, Silver for High Temperature Applications |
| ISO 9001:2015 | Quality management systems — Requirements |
| BS 4A 4-1.2:1967 | Specification for test pieces and test methods for metallic materials. Tensile tests Tensile tests - elevated temperature. Metric units |
| ISO 3161:1999 | Aerospace — UNJ threads — General requirements and limit dimensions |
| ASTM E 92 : 2017 : REDLINE | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.