SAE USCAR 33 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SPECIFICATION FOR TESTING AUTOMOTIVE LED MODULES
Hardcopy , PDF
03-14-2022
English
01-01-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. SAFETY PRECAUTIONS
3. REFERENCE STANDARDS
4. DIAGRAMS AND DEFINITIONS
5. GENERAL REQUIREMENTS
6. ANALYSIS
7. LED MODULE COMPONENTS
8. LED MODULE ASSEMBLY TESTING
9. MECHANICAL
10. ELECTRICAL
11. PHOTOMETRICS
12. END OF LINE TESTING
APPENDIX A: GLOSSARY
APPENDIX B: FLUID SOURCES
APPENDIX C: TEST SEQUENCE
APPENDIX D: DESIGN GUIDELINES
APPENDIX E: ANNUAL TESTS
APPENDIX F: REVISIONS
This specification is a general level subsystem light source specification that establishes test requirements of Light Emitting Diode (LED) components and modules for use in automotive lighting systems.
| DocumentType |
Standard
|
| Pages |
56
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE USCAR 2 : 2013 | PERFORMANCE SPECIFICATION FOR AUTOMOTIVE ELECTRICAL CONNECTOR SYSTEMS |
| AIAG FMEA : 2008 ERRATA 2011 | POTENTIAL FAILURE MODE & EFFECTS ANALYSIS |
| ISO 16750-2:2012 | Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 2: Electrical loads |
| AIAG APQP : 2ED 2008 | ADVANCED PRODUCT QUALITY PLANNING AND CONTROL PLAN (APQP) |
| SAE J 578 : 2016 | COLOR SPECIFICATION |
| SAE J 2650 : 2013 | PERFORMANCE REQUIREMENTS FOR LIGHT EMITTING DIODE (LED) ROAD ILLUMINATION DEVICES |
| ISO 16750-1:2006 | Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 1: General |
| SAE J 1330 : 2014 | PHOTOMETRY LABORATORY ACCURACY GUIDELINES |
| ASTM E 595 : 2015 : REDLINE | Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment |
| SAE USCAR 21 : 2014 | PERFORMANCE SPECIFICATION FOR CABLE-TO-TERMINAL ELECTRICAL CRIMPS |
| SAE J 1673 : 2012 | HIGH VOLTAGE AUTOMOTIVE WIRING ASSEMBLY DESIGN |
| SAE USCAR12-5 : 2017 | ELECTRICAL CONNECTOR DESIGN CRITERIA |
| SAE J 1889 : 2015 | L.E.D. SIGNAL AND MARKING LIGHTING DEVICES |
| AIAG Q7 K : LATEST | DAIMLERCHRYSLER, FORD MOTOR COMPANY, AND GENERAL MOTORS QS-9000 SUPPLIER QUALITY REQUIREMENTS |
| SAE J 1128 : 2015 | LOW VOLTAGE PRIMARY CABLE |
| SAE J 2938 : 2012 | LED LIGHT SOURCES TESTS AND REQUIREMENTS STANDARD |
| ISO 2575:2010 | Road vehicles Symbols for controls, indicators and tell-tales |
| IPC A 610 : F | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| SAE J 1344 : 1997(S2017) | MARKING OF PLASTIC PARTS |
| SAE J 2357 : 2012 | APPLICATION GUIDELINES FOR ELECTRONICALLY DRIVEN AND/OR CONTROLLED EXTERIOR AUTOMOTIVE LIGHTING EQUIPMENT |
| AIAG MSA : 2010 ERRATA | MEASUREMENT SYSTEMS ANALYSIS |
| AIAG PPAP : 2006 ERRATA 2006 | PRODUCTION PART APPROVAL PROCESS (PPAP) |
| VDA 260 : 2007 | COMPONENTS OF MOTOR VEHICLES - MARKING OF MATERIAL |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| SAE USCAR 34 : 2009 | SPECIFICATION FOR TESTING AUTOMOTIVE LAMP ASSEMBLIES |
| SAE J 575 : 2015 | TEST METHODS AND EQUIPMENT FOR LIGHTING DEVICES FOR USE ON VEHICLES LESS THAN 2032 MM IN OVERALL WIDTH |
| SAE J 1383 : 2010 | PERFORMANCE REQUIREMENTS FOR MOTOR VEHICLE HEADLAMPS |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| SAE USCAR 20 : 2004 | FIELD CORRELATED LIFE TEST - SUPPLEMENT TO SAE/USCAR-2 |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.