SAE J 1754/2 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 2: ORDERING INFORMATION
Hardcopy , PDF
09-11-2020
English
01-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. REFERENCES
3. REQUIREMENTS
4. NOTES
Provides ordering information for steel wire reinforced rubber hose assemblies using connectors specified in SAE J 516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa.
| DocumentType |
Revision
|
| Pages |
10
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE J 1273 : 2014 | RECOMMENDED PRACTICES FOR HYDRAULIC HOSE ASSEMBLIES |
| SAE J 2593 : 2015 | INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS |
| SAE J 1754/3 : 2015 | HOSE ASSEMBLIES, HYDRAULIC, J517 100R SERIES HOSE - PART 3: PROCUREMENT AND ORDERING INFORMATION |
| SAE J 1754/1 : 2017 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 1: PROCUREMENT DOCUMENT |
| SAE J 517 : 2016 | HYDRAULIC HOSE |
| SAE J 1754/3 : 2015 | HOSE ASSEMBLIES, HYDRAULIC, J517 100R SERIES HOSE - PART 3: PROCUREMENT AND ORDERING INFORMATION |
| SAE J 846 : 2015 | CODING SYSTEMS FOR IDENTIFICATION OF FLUID CONDUCTORS AND CONNECTORS |
| SAE J 1405 : 2017 | OPTIONAL TEST PROCEDURES FOR HYDRAULIC HOSE ASSEMBLIES |
| SAE J 516 : 2016 | HYDRAULIC HOSE FITTINGS |
| ISO 12151-2:2003 | Connections for hydraulic fluid power and general use — Hose fittings — Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 degree cone connector ends with O-rings |
| ISO 4397:2011 | Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes |
| SAE J 1754/1 : 2013 | HOSE ASSEMBLIES, RUBBER, HYDRAULIC, STEEL WIRE REINFORCED - PART 1: PROCUREMENT DOCUMENT |
| SAE J 1273 : 2014 | RECOMMENDED PRACTICES FOR HYDRAULIC HOSE ASSEMBLIES |
| ISO 12151-5:2007 | Connections for hydraulic fluid power and general use — Hose fittings — Part 5: Hose fittings with ISO 8434-2 37 degree flared ends |
| SAE J 343 : 2016 | TEST AND TEST PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES |
| ISO 12151-3:2010 | Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| ISO 12151-1:2010 | Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends |
| SAE J 1176 : 2012 | EXTERNAL LEAKAGE CLASSIFICATIONS FOR HYDRAULIC SYSTEMS |
| ISO 12151-6:2009 | Connections for hydraulic fluid power and general use Hose fittings Part 6: Hose fittings with ISO 8434-6 60 degree cone ends |
| ISO 12151-4:2007 | Connections for hydraulic fluid power and general use Hose fittings Part 4: Hose fittings with ISO 6149 metric stud ends |
| ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.