SAE AMS5516P
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Steel, Corrosion-Resistant, Sheet, Strip, and Plate 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated
Hardcopy , PDF
03-11-2019
English
10-12-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
Covers a corrosion-resistant steel in the form of sheet, strip, and plate.
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
| MIL-DTL-8783 Revision D:2009 | Clamp, Hose, Flat Band 500 Degrees F, General Specification for |
| SAE AMS3281F | Sealing Compound, Polysulfide (T) Synthetic Rubber for Integral Fuel Tank and Fuel Cell Cavities Low Density for Intermittent Use to 360 °F (182 °C) |
| SAE AMS3265E | Sealing Compound, Polysulfide (T) Rubber, Fuel Resistant, Non-Chromated Corrosion Inhibiting For Intermittent Use to 360 °F (182 °C) |
| SAE AS27196B | SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROCARBON RUBBER, AMS7276 |
| SAE AMS3278B | Sealing and Coating Compound, Polyurethane (PUR) Fuel Resistant High Tensile Strength / Elongation For Integral Fuel Tanks / Fuel Cavities / General Purpose |
| SAE AS27197B | SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, SILICONE RUBBER, AMS7268 |
| SAE AMS3276F | Sealing Compound, Integral Fuel Tanks and General Purpose, Intermittent Use to 360 °F (182 °C) |
| SAE AMS3102 | Sealing Compound, Polythioether Rubber Fast Curing, Light Weight (Specific Gravity 0.78, max.) for Integral Fuel Tanks and General Purpose, Intermittent Use to 360 °F (182 °C) |
| SAE AS269J | Identification of Material for AN, MS, and AS Engine and Propeller Standard Utility Parts and Also for Company Parts |
| MIL-DTL-24127 Revision A:2016 | EDUCTORS, GASOLINE, OIL, OR WATER |
| SAE AS5127B | Aerospace Standard Test Methods for Aerospace Sealants Methods for Preparing Aerospace Sealant Test Specimens |
| SAE AMS3263A | Sealing Compound, Polythioether, Ambient Cure or Immediate Heat Cure For Aircraft Structures, Fuel Resistant with Intermittent Use to 400°CF (204°CC) |
| MIL-DTL-21567 Revision B:2009 | COMPOUND, SILICONE, SOFT FILM |
| SAE AMSS8802D | Sealing Compound, Fuel Resistant, Integral Fuel Tanks and Fuel Cell Cavities |
| SAE AS27198B | SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROSILICONE RUBBER, MIL-DTL-25988 |
| SAE AMS3259B | Sealing Compound, Polythioether Nonchromated, Corrosion Inhibiting for Intermittent Use to 360°F (182°C) |
| MIL-DTL-22499 Revision D:1998 | SHIM STOCK, LAMINATED |
| SAE AS 4751 : 2005 | COUPLING ASSEMBLY, V-BAND SHEET METAL WIDE FLANGE, PNEUMATIC TUBE |
| SAE AMSDTL22499A | Shim Stock, Laminated |
| SAE AMS3277J | Sealing Compound, Polythioether Rubber Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360 °F (182 °C) |
| SAE AMS3284C | Sealing Compound, Low Adhesion, for Removable Panels and Fuel Tank Inspection Plates |
| SAE AMS2248H | Chemical Check Analysis Limits, Corrosion- and Heat-Resistant Steels and Alloys, Maraging and Other Highly Alloyed Steels, and Iron Alloys |
| ASTM A 480/A480M : 2017-11 | SPECIFICATION FOR GENERAL REQUIREMENTS FOR FLAT-ROLLED STAINLESS AND HEAT-RESISTING STEEL PLATE, SHEET, AND STRIP |
| SAE AMS2371K | Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steels and Alloys Wrought Products and Forging Stock |
| ASTM E 353 : 2014 : REDLINE | Standard Test Methods for Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys |
| SAE AS4194A | Sheet and Strip Surface Finish Nomenclature |
| SAE AMS 2807B : 2012 | IDENTIFICATION, CARBON AND LOW-ALLOY STEELS, CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS, SHEET, STRIP, PLATE, AND AIRCRAFT TUBING |
| SAE AMS 2242 : 2014 | TOLERANCES, CORROSION AND HEAT RESISTANT STEEL, IRON ALLOY, TITANIUM, AND TITANIUM ALLOY SHEET, STRIP, AND PLATE |
| ASTM E 290 : 2014 : REDLINE | Standard Test Methods for Bend Testing of Material for Ductility |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.