SAE AMS 1551 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
CLEANER, TURBINE ENGINE GAS PATH AQUEOUS TYPE
Hardcopy , PDF
08-11-2020
English
01-01-2008
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
Specifies petroleum distillate-free cleaner in the form of an aqueous-base liquid concentrate or a ready-to-use liquid.
| Committee |
AMS-J
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy |
| SAE AMS 2416 : 2010 | PLATING, NICKEL-CADMIUM DIFFUSED |
| SAE AMS 7273 : 2011 | RUBBER: FLUOROSILICONE (FVMQ) HIGH TEMPERATURE FUEL AND OIL RESISTANT FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS |
| ASTM D 4192 : 2015 : REDLINE | Standard Test Method for Potassium in Water by Atomic Absorption Spectrophotometry |
| SAE AMS 4049 : 2016 | ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 5.6ZN - 2.5MG - 1.6CU - 0.23CR (ALCLAD 7075; -T6 SHEET - T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 2475H : 2009 | PROTECTIVE TREATMENTS, MAGNESIUM ALLOYS |
| SAE AMS 4911 : 2014 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4 V, ANNEALED |
| SAE AMS 5608 : 2016 | COBALT ALLOY, CORROSION AND HEAT RESISTANT, SHEET, STRIP, AND PLATE, 40CO - 22CR - 22NI - 14.5W - 0.07LA, SOLUTION HEAT TREATED |
| ASTM D 4191 : 2015 : REDLINE | Standard Test Method for Sodium in Water by Atomic Absorption Spectrophotometry |
| ASTM D 1141 : 1998 : EDT 1 | Standard Practice for the Preparation of Substitute Ocean Water |
| SAE AMS 4376 : 2011(R2018) | PLATE, MAGNESIUM ALLOY - 3.0AL - 1.0ZN - 0.20MN (AZ31B-H26) COLD ROLLED AND PARTIALLY ANNEALED |
| SAE AMS 7276H : 2011 | RUBBER: FLUOROCARBON (FKM) HIGH-TEMPERATURE-FLUID RESISTANT LOW COMPRESSION SET FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS |
| SAE AMS 5504 : 2002 | STEEL, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 12.5CR (410), ANNEALED |
| SAE AMS 5536 : 2012 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 47.5NI - 22CR - 1.5CO - 9.0MO - 0.60W - 18.5FE, SOLUTION HEAT TREATED |
| SAE AMS 4037 : 2014 | ALUMINUM ALLOY, SHEET AND PLATE, 4.4CU - 1.5MG - 0.60MN (2024; -T3 FLAT SHEET, -T351 PLATE) SOLUTION HEAT TREATED |
| SAE AMS 7267 : 2001 | RINGS, SEALING, SILICONE (VSI) RUBBER, HEAT RESISTANT, LOW COMPRESSION SET, 70-80 |
| SAE AMS 4045 : 2016 | ALUMINUM ALLOY SHEET AND PLATE 5.6ZN - 2.5MG - 1.6CU - 0.23CR 7075: (-T6 SHEET, -T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 5544 : 2014 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 57NI - 19.5CR - 13.5CO - 4.2MO - 3.0TI - 1.4AL - 0.05ZR - 0.006B, CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED, ANNEALED |
| ASTM E 70 | TEST METHOD FOR PH OF AQUEOUS SOLUTIONS WITH THE GLASS ELECTRODE |
| SAE AMS 5510S : 2014 | STEEL, CORROSION AND HEAT-RESISTANT, SHEET, STRIP AND PLATE, 18CR - 10.5NI - 0.40TI (SAE 30321) SOLUTION HEAT TREATED |
| SAE AMS 7271 : 2010 | RINGS, SEALING, BUTADIENE-ACRYLONITRILE (NBR) RUBBER FUEL AND LOW TEMPERATURE RESISTANT 60 - 70 |
| MIL-C-81751 Revision B:1972 | Coating, Metallic-Ceramic |
| SAE AMS 4025 : 2014 | ALUMINUM ALLOY, SHEET AND PLATE, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-O) ANNEALED |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| SAE AMS 5046 : 2012 | CARBON STEEL, SHEET, STRIP, AND PLATE, (SAE 1020 AND 1025) |
| SAE ARP 1755 : 2000 | EFFECT OF CLEANING AGENTS ON AIRCRAFT ENGINE MATERIALS, STOCK LOSS TEST METHOD |
| SAE AMS 4916 : 2014 | TITANIUM ALLOY SHEET, STRIP, AND PLATE 8AL - 1MO - 1V DUPLEX ANNEALED |
| SAE AMS 5040 : 2015 | Steel, Sheet and Strip 0.15 Carbon, Maximum Deep Forming Grade |
| ASTM E 442 : 1991 | Test Method for Chlorine, Bromine, or Iodine in Organic Compounds by Oxygen Flask Combustion (Withdrawn 1997) |
| SAE AMS 2470 : 2013 | ANODIC TREATMENT OF ALUMINUM ALLOYS, CHROMIC ACID PROCESS |
| SAE AMS 5045 : 2015 | STEEL, SHEET AND STRIP, 0.25 CARBON, MAXIMUM HARD TEMPER |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.