PREN ISO 6185-3 : DRAFT 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INFLATABLE BOATS - PART 3: BOATS WITH A MAXIMUM MOTOR POWER RATING OF 15 KW AND GREATER (ISO/DIS 6185-3:2013)
08-01-2014
03-06-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Structural Materials
6 Functional components
7 Safety requirements of the completed boat
8 Performance
9 Builder's plate(s)
10 Owner's manual
11 Standard equipment
Annex A (informative) - General arrangement of a typical
Type VII boat
Annex B (informative) - General arrangement of a typical
Type VIII boat
Annex ZA (informative) - Relationship between this International
Standard and the Essential Requirements of EU Directive
94/25/EC, as amended by Directive 2003/44/EC
BIBLIOGRAPHY
Describes the minimum safety characteristics required for the design, materials to use, manufacture and testing of inflatable boats and rigid inflatable boats (Ribs) with a hull length L[H] in accordance with ISO 8666 less than 8 m with a motor power rating of 15 kW and greater.
| Committee |
SS T01
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 13/30229200 DC : 0 | Identical |
| ISO 15083:2003 | Small craft - Bilge-pumping systems |
| ISO 12215-5:2008 | Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| ISO 2896:2001 | Rigid cellular plastics Determination of water absorption |
| ISO 11192:2005 | Small craft Graphical symbols |
| ISO 7010:2011 | Graphical symbols Safety colours and safety signs Registered safety signs |
| ISO 14946:2001 | Small craft Maximum load capacity |
| ISO 4675:2017 | Rubber- or plastics-coated fabrics — Low-temperature bend test |
| ISO 11591:2011 | Small craft, engine-driven Field of vision from helm position |
| ISO 12217-3:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m |
| ISO 10088:2013 | Small craft — Permanently installed fuel systems |
| ISO 11547:1994 | Small craft — Start-in-gear protection |
| ISO 6185-4:2011 | Inflatable boats Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater |
| ISO 2411:2017 | Rubber- or plastics-coated fabrics — Determination of coating adhesion |
| ISO 11105:1997 | Small craft Ventilation of petrol engine and/or petrol tank compartments |
| ISO 11592:2001 | Small craft less than 8 m length of hull Determination of maximum propulsion power rating |
| ISO 8666:2016 | Small craft Principal data |
| ISO 8847:2004 | Small craft Steering gear Cable and pulley systems |
| ISO 15084:2003 | Small craft Anchoring, mooring and towing Strong points |
| ISO 9775:1990 | Small craft Remote steering systems for single outboard motors of 15 kW to 40 kW power |
| ISO 10133:2012 | Small craft Electrical systems Extra-low-voltage d.c. installations |
| ISO 8469:2013 | Small craft Non-fire-resistant fuel hoses |
| ISO 12217-1:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m |
| ISO 12215-3:2002 | Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| ISO 8849:2003 | Small craft Electrically operated direct-current bilge pumps |
| ISO 8848:1990 | Small craft Remote steering systems |
| ISO 10592:1994 | Small craft Hydraulic steering systems |
| ISO 15652:2003 | Small craft Remote steering systems for inboard mini jet boats |
| ISO 11812:2001 | Small craft Watertight cockpits and quick-draining cockpits |
| ISO 12215-1:2000 | Small craft — Hull construction and scantlings — Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate |
| ISO 10240:2004 | Small craft Owner's manual |
| ISO 21487:2012 | Small craft — Permanently installed petrol and diesel fuel tanks |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| ISO 13297:2014 | Small craft Electrical systems Alternating current installations |
| ISO 15085:2003 | Small craft — Man-overboard prevention and recovery |
| EN 314-2:1993 | Plywood - Bonding quality - Part 2: Requirements |
| ISO 16147:2002 | Small craft Inboard diesel engines Engine-mounted fuel and electrical components |
| ISO 15584:2001 | Small craft Inboard petrol engines Engine-mounted fuel and electrical components |
| ISO 8665:2006 | Small craft Marine propulsion reciprocating internal combustion engines Power measurements and declarations |
| ISO 3011:1997 | Rubber- or plastics-coated fabrics Determination of resistance to ozone cracking under static conditions |
| ISO 4674-1:2016 | Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods |
| ISO 10087:2006 | Small craft Craft identification Coding system |
| ISO 12215-6:2008 | Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 14945:2004 | Small craft Builder's plate |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.