PREN 1825-1 : DRAFT 1995
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
INSTALLATIONS FOR SEPARATION OF GREASE - PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL
09-01-2004
01-12-2013
0 Foreword
1 Scope
2 Normative References
3 Definitions
3.1 Grease
3.2 Influent
3.3 Installation for separation
3.4 Grease separator
3.5 Sludge trap
3.6 Extension shafts
3.7 Built-in components
3.8 Grease separation chamber
3.9 Grease collection chamber
3.10 Inlet area
3.11 Outlet area
3.12 Sampling point
3.13 Nominal size (NS)
3.14 Maximum operational liquid level
3.15 Automatic alarm device
3.16 Sizing
4 Nominal sizes
5 Requirements
5.1 Durability
5.2 Coatings/linings
5.3 Structural requirements
5.4 Structural strength
5.5 Functional requirements
6 Marking
6.1 Installations for separation
6.2 Automatic alarm devices
7 Installation, operation and maintenance instructions
7.1 Installation instructions
7.2 Operation and maintenance
8 Testing
8.1 Documentation and samples
8.2 General
8.3 Materials
8.4 Coatings/linings
8.5 Structural requirements
8.6 Hydraulic requirements
8.7 Marking
8.8 Installation, operating and maintenance instructions
8.9 Type testing
9 Quality control
9.1 General
9.2 Internal quality control carried out by the
manufacturer
9.3 External quality control carried out by a third
party
Annex A (normative) Requirements and test methods for
coatings and linings
A.1 Requirements
A.2 Test methods
Annex B (normative) Requirements for heating oil extra
light
Annex C (normative) Requirements for analysis of effluent
samples
Annex D (informative) Model schemes of quality control
Covers definitions, nominal sizes, principles of design and performance requirements, marking, testing and the quality control for installations for separation of grease.
| Committee |
TC 165
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Standards | Relationship |
| 95/101288 DC : DRAFT FEB 1995 | Identical |
| DIN EN 1825-2:2002-05 | Grease separators - Part 2: Selection of nominal size, installation, operation and maintenance; German version EN 1825-2:2002 |
| BS EN 12056-2:2000 | Gravity drainage systems inside buildings Sanitary pipework, layout and calculation |
| EN 1825-2:2002 | Grease separators - Part 2: Selection of nominal size, installation, operation and maintenance |
| BS EN 1825-2:2002 | Grease separators Selection of nominal size, installation, operation and maintenance |
| ISO 1514:2016 | Paints and varnishes — Standard panels for testing |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| EN 29002 : 1994 | QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN PRODUCTION & INSTALLATION |
| EURONORM 81 : 1969 | HOT-ROLLED PLAIN ROUND REINFORCING STEEL - DIMENSIONS, WEIGHTS, PERMISSIBLE DEVIATIONS |
| EURONORM 80 : 1985 | REINFORCING STEEL FOR NON-PRESTRESSED REINFORCEMENT; TECHNICAL TERMS OF DELIVERY |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO/R 527:1966 | Plastics Determination of tensile properties |
| EN 41 : 1975 | DETERMINATION OF THE SULFUR CONTENT OF PETROLEUM PRODUCTS BY THE WICKBOLD COMBUSTION METHOD |
| ISO 3675:1998 | Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method |
| ENV 206 : 1990 | CONCRETE - PERFORMANCE, PRODUCTION, PLACING AND COMPLIANCE CRITERIA |
| ISO 1083:2004 | Spheroidal graphite cast irons - Classification |
| EN 59:2016 | Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester |
| EN 116:2015 | Diesel and domestic heating fuels - Determination of cold filter plugging point - Stepwise cooling bath method |
| EN 63 : 1977 | GLASS REINFORCED PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES - THREE POINT METHOD |
| EN 61 : 1977 | GLASS REINFORCED PLASTICS - DETERMINATION OF TENSILE PROPERTIES |
| PREN 681-1 : DRAFT 2016 | ELASTOMERIC SEALS - MATERIAL REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER |
| ISO 2160:1998 | Petroleum products Corrosiveness to copper Copper strip test |
| EURONORM 88 PT2 : 1986 | STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP FOR GENERAL PURPOSES |
| EURONORM 88 PT1 : 1986 | FORGINGS, RUSTLESS, STEELS, WIRES |
| ISO 6615:1993 | Petroleum products Determination of carbon residue Conradson method |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 6272:1993 | Paints and varnishes — Falling-weight test |
| ISO 7253:1996 | Paints and varnishes — Determination of resistance to neutral salt spray (fog) |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| EN 62 : 1977 | GLASS REINFORCED PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING & TESTING |
| ISO 1518:1992 | Paints and varnishes Scratch test |
| EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control |
| ISO 2815:2003 | Paints and varnishes Buchholz indentation test |
| ISO 1872-1:1993 | Plastics Polyethylene (PE) moulding and extrusion materials Part 1: Designation system and basis for specifications |
| ISO 185:2005 | Grey cast irons Classification |
| ISO 630:1995 | Structural steels Plates, wide flats, bars, sections and profiles |
| EN 7 : 1974 | DETERMINATION OF ASH FROM PETROLEUM PRODUCTS |
| ISO 3405:2011 | Petroleum products Determination of distillation characteristics at atmospheric pressure |
| ISO 3105:1994 | Glass capillary kinematic viscometers — Specifications and operating instructions |
| ISO 2409:2013 | Paints and varnishes Cross-cut test |
| ENV 1992-1-1 : DRAFT 91 COR 1992 | EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - GENERAL RULES AND RULES FOR BUILDINGS |
| ISO 178:2010 | Plastics Determination of flexural properties |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| EN 29001 : 1994 | QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN DESIGN/DEVELOPMENT, PRODUCTION, INSTALLATION & SERVICING |
| ISO 3755:1991 | Cast carbon steels for general engineering purposes |
| ISO 1521:1973 | Paints and varnishes Determination of resistance to water Water immersion method |
| ISO 4628-2:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering |
| EN 60 : 1977 | GLASS REINFORCED PLASTICS - DETERMINATION OF THE LOSS ON IGNITION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.