PREN 16129 : DRAFT 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PRESSURE REGULATORS, AUTOMATIC CHANGE-OVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 100 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES
06-01-2013
01-12-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Types of regulating devices
5 Constructional characteristics
6 Performance characteristics
7 Test methods
8 Marking, packaging, instructions
Annex A (normative) - Special requirements for devices
fitted with pressure or flow rate operated
safety functions
Annex B (normative) - Special requirements for devices
fitted with a thermal shut off system
Annex C (normative) - Special requirements for devices
under extreme temperature conditions
(temperatures below -20 Degree C)
Annex D (normative) - Regulating devices for LPG
cylinders to supply appliances installed in
caravans and motor caravans or freshwater boats
Annex E (normative) - Complementary test requirements
for non metallic thermoplastic or thermal setting
materials used in the construction of devices
Annex F (normative) - Requirements for elastomeric
reinforced diaphragms
Annex G (normative) - Inlet connections
Annex H (normative) - Outlet connections
Annex I (informative) - Test method for resistance to
corrosion
Annex J (normative) - Method for measuring leaks at
test pressures less than or equal to 16 bar
Annex K (normative) - Special requirements for low
pressure fixed regulators fitted with two or
three outlets for outdoor use
Annex L (normative) - Special requirements for regulators
fitted with an inlet valve
Annex M (Normative) - Devices for LPG cylinders to supply
appliances installed in seawater boats
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 90/396/EEC
Bibliography
Describes the constructional and operational characteristics, the safety requirements, test methods and the marking of regulators and automatic change-over devices having a maximum regulated pressure of 4 bar, with a maximum capacity of 100 kg/h, for use with butane, propane and their mixtures in the vapour phase.
| Committee |
TC 181
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 16129 : 2013 | Identical |
| 10/30228056 DC : 0 | Identical |
| UNI/TR 11426 : 2011 | USE OF LPG PLANTS NOT FED BY A DISTRIBUTION NETWORK AT TEMPORARY OUTDOOR EVENTS - DESIGN, INSTALLATION, MAINTENANCE AND OPERATION |
| EN 15202:2012 | LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN ISO 4892-3:2016 | Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016) |
| ISO 565:1990 | Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings |
| EN 13878:2003 | Leisure accommodation vehicles - Terms and definitions |
| EN ISO 3166-1:2014 | Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013) |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 4892-3:2016 | Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 3166-1:2013 | Codes for the representation of names of countries and their subdivisions Part 1: Country codes |
| EN 12420:2014 | Copper and copper alloys - Forgings |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| 1990/396/EEC : 1990 | COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.