PREN 15250 : DRAFT 2012
Current
The latest, up-to-date edition.
SLOW HEAT RELEASE APPLIANCES FIRED BY SOLID FUEL - REQUIREMENTS AND TEST METHODS
01-12-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification of appliances and system boundary
for roomsealed appliances
5 Materials, design and construction
6 Safety
7 Performance
8 Appliance instructions
9 Marking
10 Evaluation of conformity
Annex A (normative) - Test methods
Annex B (normative) - Test fuels and recommended
fuels
Annex C (informative) - Calculation of an approximate
heat release curve against time
Annex D (informative) - Calculation of flue gas
temperatures on basis of DIN 4705,
EN 13384-1 and EN 15287
Annex E (normative) - Possibilities of installation for
roomsealed appliances
Annex F (informative) - Example of a suitable arrangement
for measuring the leakage rate of a
roomsealed appliance
Annex G (normative) - Measuring procedure for nitrogen
oxides (NOx)
Annex H (normative) - Measuring procedure for THC
Annex I (normative) - Measuring procedures for
particulate matter (PM)
Annex ZA (informative) - Clauses of this European
standard addressing the provisions of the
EU Construction Products Directive
Bibliography
Defines requirements relating to the design, manufacture, construction, safety and performance (efficiency and emissions) together with associated test methods and test fuels for residential slow heat release appliances fired by solid fuel (hereafter referred to as "appliances"), and provides instructions for them.
| Committee |
TC 295
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| 12/30260516 DC | Identical |
| 05/30134237 DC : DRAFT MAY 2005 | Identical |
| EN 14989-2:2007 | Chimneys - Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications - Part 2: Flue and air supply ducts for room sealed appliances |
| EN 10120:2017 | Steel sheet and strip for welded gas cylinders |
| CEN/TS 15883:2009 | Residential solid fuel burning appliances - Emission test methods |
| EN 15148:2009 | Solid biofuels - Determination of the content of volatile matter |
| EN 50165 : 97 AMD 1 2001 | ELECTRICAL EQUIPMENT ON NON-ELECTRIC APPLIANCES FOR HOUSEHOLD AND SIMILAR PURPOSES - SAFETY REQUIREMENTS |
| EN 1856-2:2009 | Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| ISO 1928:2009 | Solid mineral fuels Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value |
| EN 14918:2009 | Solid biofuels - Determination of calorific value |
| ISO 334:2013 | Solid mineral fuels Determination of total sulfur Eschka method |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| ISO 7-2:2000 | Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
| EN 13063-3:2007 | Chimneys - System chimneys with clay/ceramic flue liners - Part 3: Requirements and test methods for air flue system chimneys |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| ISO 331:1983 | Coal Determination of moisture in the analysis sample Direct gravimetric method |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 15104:2011 | Solid biofuels - Determination of total content of carbon, hydrogen and nitrogen - Instrumental methods |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 14775:2009 | Solid biofuels - Determination of ash content |
| ISO 687:2010 | Solid mineral fuels — Coke — Determination of moisture in the general analysis test sample |
| ISO 501:2012 | Hard coal — Determination of the crucible swelling number |
| EN 14774-1:2009 | Solid biofuels - Determination of moisture content - Oven dry method - Part 1: Total moisture - Reference method |
| EN 1856-1:2009 | Chimneys - Requirements for metal chimneys - Part 1: System chimney products |
| ISO 1171:2010 | Solid mineral fuels — Determination of ash |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 562:2010 | Hard coal and coke — Determination of volatile matter |
| EN 1561:2011 | Founding - Grey cast irons |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.