PREN 14471 : DRAFT 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
11-01-2013
01-12-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and designation
5 Dimensions and tolerances
6 Performance requirements
7 Test methods
8 Product information
9 Evaluation of conformity
10 Marking and labelling
Annex A (normative) - Test methods for
characterisation
Annex B (informative) - Examples of
characterisation
Annex C (normative) - Test methods to determine
the effect to long-term thermal load,
long-term condensate exposure, wet/dry
cycling and resistance to UV
Annex D (normative) - Simplified calculation of
thermal resistance for circular flues
Annex E (informative) - Method for applying an evenly
distributed load (horizontal)
Annex F (informative) - Resistance to UV
Annex G (normative) - Terminals
Annex H (normative) - Test methods for flow
resistance
Annex I (normative) - Test methods for wind effects
on pressure
Annex J (normative) - Test methods for wind effects
on recirculation
Annex K (normative) - Test method for rain water
ingress
Annex L (normative) - Test method of icing effects
Annex ZA - Clauses of this European standard
addressing the provisions of the EU
Construction Products Directive
Describes the performance requirements and test methods for system chimneys with plastic flue liners used to convey the products of combustion from appliances to the outside atmosphere under dry and wet conditions.
| Committee |
TC 166
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Standards | Relationship |
| 11/30250549 DC : 0 | Identical |
| 02/103631 DC : DRAFT MAY 2002 | Identical |
| 04/30122093 DC : 0 | EN 14989-2 - CHIMNEYS AND AIR SUPPLY DUCT SYSTEMS FOR ROOM SEALED APPLIANCES - REQUIREMENTS AND TEST METHODS - PART 2: FLUE AND AIR SUPPLY DUCTS FOR INDIVIDUAL ROOM SEALED APPLIANCES |
| 04/30122798 DC : DRAFT SEP 2004 | EN 15035 - HEATING BOILERS - ROOM SEALED OPERATIONS FOR BOILERS FOR FUEL OIL |
| 04/30115682 DC : DRAFT JUN 2004 | EN 14989-1 - CHIMNEYS AND AIR SUPPLY DUCT SYSTEMS FOR ROOMSEALED APPLIANCES - REQUIREMENTS AND TEST METHODS - PART 1: VERTICAL TERMINALS FOR C6-TYPE APPLIANCES |
| 05/30136031 DC : 0 | EN 15287-1 - CHIMNEYS - DESIGN, INSTALLATION AND COMMISSIONING OF CHIMNEYS - PART 1: CHIMNEYS FOR NON-ROOMSEALED HEATING APPLIANCES |
| ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
| EN ISO 14021:2016 | Environmental labels and declarations - Self-declared environmental claims (Type II environmental labelling) (ISO 14021:2016) |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN 13216-1:2004 | Chimneys - Test methods for system chimneys - Part 1: General test methods |
| ISO 14021:2016 | Environmental labels and declarations — Self-declared environmental claims (Type II environmental labelling) |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| EN 13501-2:2016 | Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11357-3:2011 | Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
| EN 13823:2010+A1:2014 | Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item |
| EN 14241-1:2013 | Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners |
| EN 13384-1:2015 | Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one heating appliance |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN 14471:2013+A1:2015 | Chimneys - System chimneys with plastic flue liners - Requirements and test methods |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| EN 13084-1:2007 | Free-standing chimneys - Part 1: General requirements |
| EN 1443:2003 | Chimneys - General requirements |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN 1856-1:2009 | Chimneys - Requirements for metal chimneys - Part 1: System chimney products |
| EN 14297:2004 | Chimneys - Freeze-thaw resistance test method for chimney products |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| EN ISO 306:2013 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| EN 513:1999 | Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.