PREN 13483 : DRAFT 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION
06-01-2013
01-12-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials and construction
6 Pressure requirements
7 Dimensions and tolerances
8 Physical properties
9 End fittings
10 Type tests
11 Frequency of testing
12 Marking
Annex A (normative) - Test method for determination
of low temperature class resistance
at -30 degrees C and -40 degrees C
Annex B (normative) - Test method for pressure
requirements of vapour recovery hoses
and tubes
Annex C (normative) - Test method for determination
of change in length due to swelling
Annex D (normative) - Test method for determination
of pressure loss
Annex E (normative) - Method for determination of
adhesion between components
Annex F (normative) - Test method for the determination
of low temperature flexibility
Annex G (normative) - Test method for the determination
of rate of fuel permeation
Annex H (normative) - Test method for flammability
Annex I (normative) - Test method for the determination
of leakage (leak test)
Annex J (normative) - Test method for fatigue strength
under reversed bending stresses (flex test)
Annex K (normative) - End-fitting pull-off test
Annex L (normative) - Test frequency for type tests and
routine tests
Annex M (informative) - Test frequency for production
acceptance tests
Bibliography
Describes the requirements for hose assemblies with vapour recovery for delivery systems on petrol filling stations.
| Committee |
TC 218
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 11/30250273 DC : 0 | Identical |
| 03/300798 DC : DRAFT JAN 2003 | Identical |
| 02/709495 DC : DRAFT JULY 2002 | EN 13617-4 - PETROL FILLING STATIONS - PART 4: SAFETY AND ENVIRONMENTAL REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS |
| EN ISO 8330:2014 | Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014) |
| EN ISO 1402:2009 | Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009) |
| EN 228:2012+A1:2017 | Automotive fuels - Unleaded petrol - Requirements and test methods |
| ISO 6801:1983 | Rubber or plastics hoses Determination of volumetric expansion |
| ISO 4649:2017 | Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device |
| EN ISO 1307:2008 | Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006) |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN ISO 8031:2009 | Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009) |
| EN ISO 7326:2016 | Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326:2016) |
| ISO 7326:2016 | Rubber and plastics hoses Assessment of ozone resistance under static conditions |
| EN ISO 8033:2017 | Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016) |
| ISO 8330:2007 | Rubber and plastics hoses and hose assemblies Vocabulary |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 4671:2007 | Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies |
| ISO 554:1976 | Standard atmospheres for conditioning and/or testing — Specifications |
| ISO 1402:2009 | Rubber and plastics hoses and hose assemblies Hydrostatic testing |
| ISO 1307:2006 | Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses |
| ISO 8033:2016 | Rubber and plastics hoses Determination of adhesion between components |
| ISO 8031:2009 | Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.