PREN 10208-3 : DRAFT 1997
Current
The latest, up-to-date edition.
PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 3: PIPES OF REQUIREMENT CLASS C
01-12-2013
Foreword
Introduction
1 Scope
2 Normative References
3 Definitions
3.1 General
3.2 Types of pipes and welds
3.3 Treatment condition
3.4 Imperfections and defects
3.5 Agreement
3.6 Margin symbols
4 Classification and designation
4.1 Classification
4.2 Designation
5 Information to be supplied by the purchaser
5.1 Mandatory information
5.2 Other information
5.3 Examples of ordering
6 Manufacturing
6.1 General
6.2 Steelmaking
6.3 Pipe manufacturing
6.4 Delivery condition
6.5 Sizing
6.6 Strip/plate end welds
6.7 Jointers
7 Requirements
7.1 General
7.2 Chemical composition
7.3 Mechanical and technological properties
7.4 Weldability
7.5 Surface conditions, imperfections and defects
7.6 Dimensions, masses and tolerances
7.6.1 Dimensions
7.6.2 Masses
7.6.3 Tolerances on the pipe
7.6.4 Finish of pipe ends
7.6.5 Tolerances of the weld seam
7.6.6 Mass tolerance
8 Inspection
8.1 Types of inspection and inspection documents
8.2 Specific inspection and testing
8.2.1 Type and frequency of tests
8.2.2 Selection and preparation of samples and test pieces
8.2.3 Test methods
8.2.3.1 Chemical analysis (product analysis)
8.2.3.2 Tensile test
8.2.3.3 Impact test
8.2.3.4 Drop weight tear (DWT) test
8.2.3.5 Crack tip opening displacement (CTOD) test
8.2.3.6 Bend test
8.2.3.7 Flattening test
8.2.3.8 Macrographic and metallographic examination
8.2.3.9 Hydrogen induced cracking test
8.2.3.10 Sulphide stress cracking test
8.2.3.11 Hardness test
8.2.3.12 Hydrostatic test
8.2.3.13 Visual examination
8.2.3.14 Dimensional testing
8.2.3.15 Weighing
8.2.3.16 Non-destructive testing
8.2.4 Retests, sorting and reprocessing
9 Marking of the pipes
9.1 General marking
9.2 Special marking
10 Coatings for temporary protection
Annex A Correspondence with API 5L steel grades (informative)
Annex B Manufacturing procedure qualification (normative)
Annex C Treatment of imperfections and defects disclosed by visual
examination (normative)
Annex D Non-destructive testing (normative)
Annex E Bibliography (informative)
Annex F Differences between this ISO/DIS 3183-3 and prEN 10208-3
(informative)
Describes the technical delivery conditions for unalloyed and alloyed (except stainless) seamless and welded steel pipes.
Committee |
ECISS/TC 29
|
DocumentType |
Draft
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
97/703009 DC : 0 | Identical |
NEN EN 10208-3 : DRAFT 1997 | Identical |
ISO 404:2013 | Steel and steel products — General technical delivery requirements |
ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
ISO 6929:2013 | Steel products — Vocabulary |
ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
EN 10079:2007 | Definition of steel products |
EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
ISO/TR 9769:1991 | Steel and iron Review of available methods of analysis |
API 5L3 : 2014 | DROP-WEIGHT TEAR TESTS ON LINE PIPE |
NACE TM 02 84 : 2016 | EVALUATION OF PIPELINE AND PRESSURE VESSEL STEELS FOR RESISTANCE TO HYDROGEN-INDUCED CRACKING |
EURONORM 5 : 1979 | VICKERS HARDNESS MEASUREMENT FOR STEEL |
EN ISO 377:2017 | Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017) |
ISO 12094:1994 | Welded steel tubes for pressure purposes Ultrasonic testing for the detection of laminar imperfections in strips/plates used in the manufacture of welded tubes |
ISO 4885:2017 | Ferrous materials Heat treatments Vocabulary |
NACE TM 01 77 : 2016 | LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS |
ISO 9303:1989 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of longitudinal imperfections |
ISO 9304:1989 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Eddy current testing for the detection of imperfections |
EN ISO 9002:1994/AC:1997 | QUALITY SYSTEMS - SPECIFICATION FOR PRODUCTION AND INSTALLATION |
ISO 11496:1993 | Seamless and welded steel tubes for pressure purposes Ultrasonic testing of tube ends for the detection of laminar imperfections |
EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
EN 910 : 1996 | DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - BEND TESTS |
ISO/TR 4949:1989 | Steel names based on letter symbols |
EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
ISO 9598:1989 | Seamless steel tubes for pressure purposes Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of transverse imperfections |
ISO 4948-1:1982 | Steels Classification Part 1: Classification of steels into unalloyed and alloy steels based on chemical composition |
ISO 7438:2016 | Metallic materials Bend test |
ISO 9402:1989 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of longitudinal imperfections |
ISO 13664:1997 | Seamless and welded steel tubes for pressure purposes Magnetic particle inspection of the tube ends for the detection of laminar imperfections |
EN 10246-7:2005 | Non-destructive testing of steel tubes - Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc welded) tubes for the detection of longitudinal imperfections |
ISO 10543:1993 | Seamless and hot-stretch-reduced welded steel tubes for pressure purposes Full peripheral ultrasonic thickness testing |
EN 10021:2006 | General technical delivery conditions for steel products |
ISO 148:1983 | Steel — Charpy impact test (V-notch) |
ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
ISO 6761:1981 | Steel tubes Preparation of ends of tubes and fittings for welding |
ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
EN 10233 : 1993 | METALLIC MATERIALS - TUBE - FLATTENING TEST |
ISO 6508:1986 | Metallic materials Hardness test Rockwell test (scales A - B - C - D - E - F - G - H - K) |
ISO 10474:2013 | Steel and steel products — Inspection documents |
EN 10204:2004 | Metallic products - Types of inspection documents |
ISO 13665:1997 | Seamless and welded steel tubes for pressure purposes Magnetic particle inspection of the tube body for the detection of surface imperfections |
ISO 12135:2016 | Metallic materials Unified method of test for the determination of quasistatic fracture toughness |
ISO 11484:2009 | Steel products — Employer's qualification system for non-destructive testing (NDT) personnel |
EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
ENV 10220 : 1993 | SEAMLESS AND WELDED STEEL TUBES - DIMENSIONS AND MASSES PER UNIT LENGTH |
ISO 8492:2013 | Metallic materials Tube Flattening test |
ISO 3183-1:1996 | Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 1: Pipes of requirement class A |
ISO 4948-2:1981 | Steels Classification Part 2: Classification of unalloyed and alloy steels according to main quality classes and main property or application characteristics |
EN 10020:2000 | Definition and classification of grades of steel |
ISO 9764:1989 | Electric resistance and induction welded steel tubes for pressure purposes Ultrasonic testing of the weld seam for the detection of longitudinal imperfections |
EURONORM 168 : 1986 | IRON AND STEEL PRODUCTS - INSPECTION DOCUMENTS, CONTENTS |
ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
ISO 9765:1990 | Submerged arc-welded steel tubes for pressure purposes Ultrasonic testing of the weld seam for the detection of longitudinal and/or transverse imperfections |
ISO 1027:1983 | Radiographic image quality indicators for non-destructive testing Principles and identification |
ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
ISO 12096:1996 | Submerged arc-welded steel tubes for pressure purposes Radiographic testing of the weld seam for the detection of imperfections |
ISO 10124:1994 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Ultrasonic testing for the detection of laminar imperfections |
ISO 13663:1995 | Welded steel tubes for pressure purposes Ultrasonic testing of the area adjacent to the weld seam for the detection of laminar imperfections |
EN 10109-1 : 1994 | METALLIC MATERIALS - HARDNESS TEST - PART 1: ROCKWELL TEST (SCALES A, B, C, D, E, F, G, H, K) AND ROCKWELL SUPERFICIAL TEST (SCALES 15N, 30N, 45N, 15T, 30T AND 45T) |
CR 10260 : 1998 | DESIGNATION SYSTEMS FOR STEEL - ADDITIONAL SYMBOLS |
ISO 9305:1989 | Seamless steel tubes for pressure purposes Full peripheral ultrasonic testing for the detection of transverse imperfections |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.