PPI TR 4 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HDB/HDS/SDB/PDB/MRS LISTED MATERIALS - PPI LISTING OF HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESS (HDS), STRENGTH DESIGN BASIS (SDB), PRESSURE DESIGN BASIS (PDB) AND MINIMUM REQUIRED STRENGTH (MRS) RATINGS FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
09-21-2024
03-14-2017
Foreword
Notes to the Reader
Definitions and Acronyms
Common Plastics Abbreviations
SECTION I - MATERIALS WITH PPI RECOMMENDED HYDROSTATIC DESIGN BASIS (HDB) OR STRENGTH DESIGN BASIS (SDB) ESTABLISHED IN ACCORDANCE WITH PPI TR-3 (ASTM D 2837)
SECTION II - PIPES WITH PPI RECOMMENDED PRESSURE DESIGN BASIS (PDB) AND MAXIMUM PRESSURE RATINGS (PR) ESTABLISHED IN ACCORDANCE WITH PPI TR-3 (ASTM D 2837)
SECTION III - MATERIALS WITH PPI RECOMMENDED MINIMUM REQUIRED STRENGTH (MRS) AND CATEGORIZED REQUIRED STRENGTH (CRS) ESTABLISHED IN ACCORDANCE WITH ISO 9080 AND ISO 12162
APPENDIX
Provides lists thermoplastic piping materials with a Plastics Pipe Institute (PPI) recommended Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB) or Minimum Required Strength (MRS) rating for thermoplastic piping materials or pipe.
| DocumentType |
Standard
|
| PublisherName |
The Plastics Pipe Institute Inc.
|
| Status |
Superseded
|
| SupersededBy |
| ASTM F 2018 : 2000 : EDT 1 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| ASTM F 2807 : 2013 | Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications |
| ASTM F 1948 : 2015 : REDLINE | Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing |
| AWWA M55 : 1 | PE PIPE - DESIGN AND INSTALLATION |
| AWWA C906:2015 | POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS |
| ASTM F 2145 : 2013 : R2018 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| CSA Z662.1 : 2013 | COMMENTARY ON CSA Z662-07, OIL AND GAS PIPELINE SYSTEMS |
| ASTM F 2018 : 2000 : R2010 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens (Withdrawn 2019) |
| ASTM F 2737 : 2011 : R2017 | Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units |
| ASTM F 1924 : 2012 : REDLINE | Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing |
| ASTM F 2737 : 2011 | Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units |
| CSA B137.19 : 2017 | BLACK CROSSLINKED POLYETHYLENE (PEX) PIPING SYSTEMS FOR GAS SERVICES |
| ASTM F 2929 : 2017 : REDLINE | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM F 2619/F2619M : 2013 : REDLINE | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM F 2968/F2968M : 2014 | Standard Specification for Black Crosslinked Polyethylene (PEX) Pipe, Fittings and Joints For Gas Distribution Applications |
| ASTM F 2145 : 2013 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| ASTM F 2018 : 2000 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| ASTM F 876 : 2017 : REDLINE | SPECIFICATION FOR CROSSLINKED POLYETHYLENE (PEX) TUBING |
| ASTM F 2829 : 2010 | Standard Specification for Metric-Sized Crosslinked Polyethylene (PEX) Pipe Systems |
| NSF 358-1 : 2014 | POLYETHYLENE PIPE AND FITTINGS FOR WATER-BASED GROUND-SOURCE 'GEOTHERMAL' HEAT PUMP SYSTEMS |
| ASTM F 714 : 2013 : REDLINE | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM F 2261 : 2006 : R2011 | Standard Test Method for Pressure Rating Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 and 80 Socket-Type |
| ASTM F 2261 : 2006 | Standard Test Method for Pressure Rating Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 and 80 Socket-Type |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM F 2905/F2905M : 2013 | Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings and Joints For Oil and Gas Producing Applications |
| FM 1613 : 2017 | POLYETHYLENE (PE) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE |
| ASTM F 2805 : 2016 : REDLINE | Standard Specification for Multilayer Thermoplastic And Flexible Steel Pipe And Connections |
| ANSI/AWWA C903:2016 | POLYETHYLENE-ALUMINUM-POLYETHYLENE (PEALPE) COMPOSITE PRESSURE PIPE, 12 MM (1/2 IN.) THROUGH 51 MM (2 IN.), FOR WATER SERVICE |
| ASTM F 2807 : 2013 : R2018 | Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications (Withdrawn 2024) |
| ASTM F 2018 : 2000 : R2006 | Standard Test Method for Time-to-Failure of Plastics Using Plane Strain Tensile Specimens |
| ASME B16.33 : 2012 : R2017 | MANUALLY OPERATED METALLIC GAS VALVES FOR USE IN GAS PIPING SYSTEMS UPTO 175 PSI (SIZES NPS 1/2 THROUGH NPS 2) |
| ASME B16.33 : 2012 | MANUALLY OPERATED METALLIC GAS VALVES FOR USE IN GAS PIPING SYSTEMS UPTO 175 PSI (SIZES NPS 1/2 THROUGH NPS 2) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.