PD CEN/TS 16354:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Laminate floor coverings. Underlays. Specification, requirements and test methods
Hardcopy , PDF
11-20-2018
English
02-28-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Marking and labelling
Annex A (normative) - Determination of thickness,
length, width, squareness, flatness, punctual
conformability, compressive strength,
compressive creep resistance, dynamic
load resistance and area weight
Annex B (informative) - Proposed performance classes
Bibliography
Defines test methods for the determination of the technical characteristics of underlays under laminate floor coverings and covers minimum performance requirements for the underlay-flooring system to give satisfactory service and to encourage the consumer to make an informed choice.
| Committee |
PRI/60
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
This Technical Specification specifies test methods for the determination of the technical characteristics of underlays under laminate floor coverings. It includes minimum performance requirements for the underlay-flooring system to give satisfactory service and to encourage the consumer to make an informed choice. It also specifies requirements for marking and packaging. Underlays pre-attached to the laminate flooring coverings are not covered by this Technical Specification. Underlays for laminate floor coverings intended for use in electrostatically sensitive areas like computer rooms, etc., are not covered by this Technical Specification.
| Standards | Relationship |
| CEN/TS 16354:2013 | Identical |
| EN 12667:2001 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance |
| EN 1264-3:2009 | Water based surface embedded heating and cooling systems - Part 3: Dimensioning |
| EN 1606:2013 | Thermal insulating products for building applications - Determination of compressive creep |
| ISO 10140-2:2010 | Acoustics Laboratory measurement of sound insulation of building elements Part 2: Measurement of airborne sound insulation |
| EN 1815:1997 | Resilient and textile floor coverings - Assessment of static electrical propensity |
| ISO 1923:1981 | Cellular plastics and rubbers — Determination of linear dimensions |
| ISO 717-2:2013 | Acoustics Rating of sound insulation in buildings and of building elements Part 2: Impact sound insulation |
| EN 13329:2016+A1:2017 | Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications, requirements and test methods |
| EN 15468:2016 | Laminate floor coverings - Elements with directly applied printing and resin surface layer - Specifications, requirements and test methods |
| EN 824:2013 | Thermal insulating products for building applications - Determination of squareness |
| EN 717-1:2004 | Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| EN 825:2013 | Thermal insulating products for building applications - Determination of flatness |
| EN ISO 717-2:2013 | Acoustics - Rating of sound insulation in buildings and of building elements - Part 2: Impact sound insulation (ISO 717-2:2013) |
| EN 823:2013 | Thermal insulating products for building applications - Determination of thickness |
| EN 12311-2:2013 | Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN 13238:2010 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| EN 13793:2003 | Thermal insulating products for building applications - Determination of behaviour under cyclic loading |
| EN ISO 1923:1995 | Cellular plastics and rubbers - Determination of linear dimensions (ISO 1923:1981) |
| EN 12664:2001 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Dry and moist products of medium and low thermal resistance |
| ISO 16000-9:2006 | Indoor air — Part 9: Determination of the emission of volatile organic compounds from building products and furnishing — Emission test chamber method |
| EN ISO 10140-2:2010 | Acoustics - Laboratory measurement of sound insulation of building elements - Part 2: Measurement of airborne sound insulation (ISO 10140-2:2010) |
| EN 14909:2012 | Flexible sheets for waterproofing - Plastic and rubber damp proof courses - Definitions and characteristics |
| ISO 717-1:2013 | Acoustics Rating of sound insulation in buildings and of building elements Part 1: Airborne sound insulation |
| EN 438-2:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN 14978:2016 | Laminate floor coverings - Elements with acrylic based surface layer, electron beam cured - Specifications, requirements and test methods |
| ISO 10140-3:2010 | Acoustics Laboratory measurement of sound insulation of building elements Part 3: Measurement of impact sound insulation |
| ISO 10140-5:2010 | Acoustics Laboratory measurement of sound insulation of building elements Part 5: Requirements for test facilities and equipment |
| EN 826:2013 | Thermal insulating products for building applications - Determination of compression behaviour |
| EN 12086:2013 | Thermal insulating products for building applications - Determination of water vapour transmission properties |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| EN 822:2013 | Thermal insulating products for building applications - Determination of length and width |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.