PD 308:1996
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Guide to the European standards for engineering drawing in the BS EN series
Hardcopy , PDF
08-03-2017
English
06-15-1996
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
Listings of BS EN series standards
Section 1. General
1.1 General
1.2 BS EN ISO 10209-1
1.3 BS EN ISO 5457
1.4 BS EN ISO 7200
1.5 BS EN ISO 5455
1.6 BS EN ISO 128
1.7 BS EN ISO 3098
1.8 BS EN ISO 6433
1.9 Symbols and abbreviations
1.10 BS EN ISO 6413
1.11 BS EN ISO 6410-1 and BS EN ISO 6410-2
1.12 BS EN ISO 8826-1
1.13 BS EN ISO 9222-1 and BS EN ISO 9222-2
1.14 BS EN ISO 2203
1.15 BS EN ISO 2162-1, BS EN ISO 2162-2 and
BS EN ISO 2162-3
1.16 BS EN ISO 6410-3
1.17 BS EN ISO 6411
Section 2. Dimensioning and tolerancing
2.1 General
2.2 BS EN ISO 129
2.3 BS EN ISO 406
2.4 BS EN ISO 1660
2.5 BS EN ISO 3040
2.6 BS EN ISO 8015
2.7 BS EN ISO 1302
Section 3. Geometrical tolerancing
3.1 General
3.2 BS EN ISO 1101
3.3 BS EN ISO 5459
3.4 BS EN ISO 2692
3.5 BS EN ISO 5458
3.6 BS EN ISO 7083
3.7 Straightness, flatness, circularity and
cylindricity assessment
Cross referencing index classified by BS 308 clause nos.
Cross referencing index classified by subject
Annex A CEN adoption of ISO standards on technical
drawings subjects not covered by BS 308
Compares the new European standards in the BS EN series and BS 308: Parts 1, 2 and 3 by commentary on a subject basis and by cross-referencing indexes.
| Committee |
TPR/1
|
| DevelopmentNote |
Reviewed and confirmed by BSI, February 2012. (01/2012)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| BS EN ISO 2203:1997 | Technical drawing. Conventional representation of gears |
| BS EN ISO 9222-2:1995 | Technical drawings. Seals for dynamic application Detailed simplified representation |
| BS EN ISO 11442-3:1996 | Technical product documentation. Handling of computer-based technical information Phases in the product design process |
| BS EN ISO 1302:2002 | Geometrical product specifications (GPS). Indication of surface texture in technical product documentation |
| BS EN ISO 5456-2:1999 | Technical drawings. Projection methods Orthographic representations |
| BS EN ISO 5459:2011 | Geometrical product specifications (GPS). Geometrical tolerancing. Datums and datum systems |
| BS EN ISO 5455:1995 | Technical drawings. Scales |
| BS EN ISO 1660:2017 | Geometrical product specifications (GPS). Geometrical tolerancing. Profile tolerancing |
| BS EN ISO 7200:2004 | Technical product documentation. Data fields in title blocks and document headers |
| BS EN ISO 10579:2013 | Geometrical product specifications (GPS). Dimensioning and tolerancing. Non-rigid parts |
| BS EN ISO 3040:2016 | Geometrical product specifications (GPS). Dimensioning and tolerancing. Cones |
| BS EN ISO 2162-1:1996 | Technical product documentation. Springs Simplified representation |
| BS EN ISO 6433:2012 | Technical product documentation. Part references |
| BS EN ISO 1101:2017 | Geometrical product specifications (GPS). Geometrical tolerancing. Tolerances of form, orientation, location and run-out |
| BS EN ISO 5261:1999 | Technical drawings. Simplified representation of bars and profile sections |
| BS EN ISO 6412-2:1995 | Technical drawings. Simplified representation of pipelines Isometric projection |
| BS EN ISO 10209-2:1996 | Technical product documentation. Vocabulary Terms relating to projection methods |
| BS EN ISO 11442-1:1996 | Technical product documentation. Handling of computer-based technical information Security requirements |
| BS EN ISO 5457 : 1999 | TECHNICAL PRODUCT DOCUMENTATION - SIZES AND LAYOUT OF DRAWING SHEETS |
| BS EN ISO 6412-1:1995 | Technical drawings. Simplified representation of pipelines General rules and orthogonal representation |
| BS EN ISO 3098-0:1998 | Technical product documentation. Lettering. General requirements |
| BS EN ISO 2692:2014 | Geometrical product specifications (GPS). Geometrical tolerancing. Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| BS EN ISO 6413:1995 | Technical drawings. Representation of splines and serrations |
| BS EN ISO 6412-3:1996 | Technical drawings. Simplified representation of pipelines Terminal features of ventilation and drainage systems |
| BS EN ISO 11442-2:1996 | Technical product documentation. Handling of computer-based technical information Original documentation |
| BS EN ISO 6411:1997 | Technical drawings. Simplified representation of centre holes |
| BS EN ISO 8826-1:1995 | Technical drawings. Roller bearings General simplified representation |
| BS EN ISO 9222-1:1995 | Technical drawings. Seals for dynamic application General simplified representation |
| BS EN ISO 8015:2011 | Geometrical product specifications (GPS). Fundamentals. Concepts, principles and rules |
| BS EN ISO 5458:1999 | Geometrical product specifications (GPS). Geometrical tolerancing. Positional tolerancing |
| BS EN ISO 11442-4:1996 | Technical product documentation. Handling of computer-based technical information Document management and retrieval systems |
| BS EN ISO 7083:1995 | Technical drawings. Symbols for geometrical tolerancing. Proportions and dimensions |
| BS EN ISO 6410-1:1996 | Technical drawings. Screw threads and threaded parts General conventions |
| BS EN ISO 5456-3:1999 | Technical drawings. Projection methods Axonometric representations |
| BS EN ISO 5456-1:1999 | Technical drawings. Projection methods Synopsis |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.