ONORM EN ISO 75-3 : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 3: HIGH-STRENGTH THERMOSETTING LAMINATES AND LONG-FIBRE-REINFORCED PLASTICS
01-12-2013
11-03-2025
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Test specimens
7 Conditioning
8 Procedure
9 Expression of results
10 Precision
11 Test report
Bibliography
Provides a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm.
| Committee |
TC 074
|
| DocumentType |
Standard
|
| PublisherName |
Osterreichisches Normungsinstitut/Austrian Standards
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN ISO 75-3 : 2005 | Identical |
| DIN EN ISO 75-3:2004-09 | Identical |
| NEN EN ISO 75-3 : 2004 C11 2007 | Identical |
| I.S. EN ISO 75-3:2004 | Identical |
| BS EN ISO 75-3:2004 | Identical |
| ISO 75-3:2004 | Identical |
| NBN EN ISO 75-3 : 2004 COR 2006 | Identical |
| NS EN ISO 75-3 : 2ED 2004 | Identical |
| UNE-EN ISO 75-3:2005 | Identical |
| ONORM EN 14427 : 2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION |
| ISO 75-1:2013 | Plastics — Determination of temperature of deflection under load — Part 1: General test method |
| EN ISO 10724-1:2001 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998) |
| ISO 1268-4:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 4: Moulding of prepregs |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| EN ISO 75-1:2013 | Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2013) |
| EN ISO 2818:1996 | Plastics - Preparation of test specimens by machining (ISO 2818:1994) |
| EN ISO 295:2004 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| ISO 14125:1998 | Fibre-reinforced plastic composites — Determination of flexural properties |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 178:2010 | Plastics — Determination of flexural properties |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.