ONORM EN 1218-5 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
10-21-2021
01-12-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 General
3.2 Terms
3.3 Definitions
4 List of significant hazards
5 Safety requirements and/or measures
5.1 General
5.2 Controls
5.2.1 Safety and reliability of control systems
5.2.2 Position of controls
5.2.3 Starting
5.2.4 Normal stopping
5.2.5 Emergency stop
5.2.6 Integrated feed
5.2.7 Positioning of tool spindles
5.2.8 Speed changing
5.2.9 Failure of the power supply
5.2.10 Failure of control circuits
5.3 Protection against mechanical hazards
5.3.1 Stability
5.3.2 Hazard resulting from break-up
5.3.3 Tool holder and tool design
5.3.4 Braking
5.3.5 Devices to minimise the possibility or the effect
of ejection
5.3.6 Work-piece supports and guides
5.3.7 Prevention of access to moving parts
5.4 Protection against non-mechanical hazards
5.4.1 Fire
5.4.2 Noise
5.4.3 Emission of chips and dust
5.4.4 Electricity
5.4.5 Ergonomics and handling
5.4.6 Lighting
5.4.7 Pneumatics
5.4.8 Hydraulics
5.4.9 Radiation
5.4.10 Static electricity
5.4.11 Errors of fitting
5.4.12 Isolation
5.4.13 Maintenance
6 Information for use
6.1 Warning devices
6.2 Marking
6.3 Instruction handbook
Annex A (informative) Examples of safety related electronic
control systems
Annex B (normative) Tool spindle dimensional tolerances
Annex C (normative) Operating conditions for noise emission
measurement
C.1 General
C.2 Noise measurements
C.2.1 Test conditions
C.2.2 Microphone positions
C.2.3 General data sheet
Annex D (informative) Safe working practice
Annexe ZA (informative) Relationship of this document with
EC Directives
Bibliography
Specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to one side profiling machines with fixed table and feed rollers or feed chain hereinafter referred to as "machines", where the loading and unloading is manual and where the maximum work-piece height capacity is 200 mm.
| DocumentType |
Standard
|
| PublisherName |
Osterreichisches Normungsinstitut/Austrian Standards
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNI EN 1218-5 : 2010 | Identical |
| NEN EN 1218-5 : 2004 + A1 2009 | Identical |
| SN EN 1218-5 : 2004 + A1 2010 | Identical |
| BS EN 1218-5 : 2004 | Identical |
| DIN EN 1218-5:2010-02 | Identical |
| I.S. EN 1218-5:2004 | Identical |
| NF EN 1218-5 : 2004 + A1 2010 | Identical |
| EN 1218-5:2004+A1:2009 | Identical |
| UNE-EN 1218-5:2005 | Identical |
| NBN EN 1218-5 : 2004 + A1 2009 | Identical |
| NS EN 1218-5 : 2004 + A1 2009 | Identical |
| ONORM EN ISO 3743-2 : 2009 | ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 354:2003 | Acoustics — Measurement of sound absorption in a reverberation room |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| ONORM EN 1837 : 2009 | SAFETY OF MACHINERY - INTEGRAL LIGHTING OF MACHINES |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ONORM EN ISO 13849-1 : 2016 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN (ISO 13849-1:2015) |
| ONORM EN ISO 11204 : AUG 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| ONORM EN ISO 11202 : 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.