ONORM EN 1218-1 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE
10-21-2021
01-12-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 List of hazards
5 Safety requirements and/or measures
5.1 Controls
5.2 Protection against mechanical hazards
5.3 Protection against non-mechanical hazards
6 Information for use
6.1 Warning devices
6.2 Marking
6.3 Instruction handbook
Annex A (informative) Safe working practice
Annex B (normative) Geometrical performance for the
tool holder (spindle) (taken from
ISO 7988:1988)
Annex C (informative) Examples of safety related control
systems
Annex D (informative) Bibliography
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements
or other provisions of EU
Directives
Defined requirements and/or measures to remove the hazards and limit the risk on single end tenoning machines with sliding table, referred to as "machine". These are designed to cut solid wood, fibreboard, chipboard, plywood and materials where they are covered with plastic edgings or laminates.
| Committee |
TC-028
|
| DocumentType |
Standard
|
| PublisherName |
Osterreichisches Normungsinstitut/Austrian Standards
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NEN EN 1218-1 : 1999 + A1 2009 | Identical |
| UNE-EN 1218-1:2000 | Identical |
| SN EN 1218-1 : 1999 + A1 2010 | Identical |
| EN 1218-1:1999+A1:2009 | Identical |
| I.S. EN 1218-1:2000 | Identical |
| NS EN 1218-1 : 1999 + A1 2009 | Identical |
| BS EN 1218-1 : 1999 | Identical |
| UNI EN 1218-1 : 2009 | Identical |
| NBN EN 1218-1 : 1999 + A1 2009 | Identical |
| DIN EN 1218-1:2010-02 | Identical |
| NF EN 1218-1 : 2000 + A1 2009 | Identical |
| ONORM EN ISO 3743-2 : 2009 | ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| ONORM EN ISO 13857 : 2008 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER LIMBS |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ONORM EN ISO 11204 : AUG 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| ONORM EN ISO 11202 : 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.