ONORM EN 12012-4 : 2010
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 4: SAFETY REQUIREMENTS FOR AGGLOMERATORS
07-15-2019
01-12-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
4.1 Mechanical hazards
4.2 Thermal hazards
4.3 Noise hazards
4.4 Hazards generated by dust, fumes and gases
4.5 Hazards due to electrical energy
4.6 Hazards due to unexpected start-up
4.7 Falls from height
5 Safety requirements and/or protective measures
5.1 General
5.2 Mechanical hazards
5.2.1 Access through openings in the agglomerator chamber
5.2.2 Feed material that is not pre-cut
5.2.3 Ejection of parts or materials from the agglomerator
chamber
5.2.4 Strength
5.3 Thermal hazards
5.4 Noise hazards
5.4.1 Noise reduction at source by design
5.4.2 Noise reduction by protective measures
5.4.3 Information connected with noise hazards
5.5 Hazards generated by dust, fumes and gases
5.6 Hazards due to electrical energy
5.6.1 Electrical equipment
5.6.2 Accumulation of electrostatic charges
5.7 Unexpected start-up
5.8 Falls from height
6 Verification of conformity with the safety requirements
and/or protective measures
7 Information for use
7.1 Instruction manual
7.2 Marking
Annex A (normative) Noise test code
A.1 Scope
A.2 Determination of sound power levels
A.2.1 Basic standards
A.2.2 Measurement uncertainty
A.3 Determination of emission sound pressure level at the
workstation(s)
A.3.1 Basic standards
A.3.2 Measurement uncertainty
A.4 Installation and mounting conditions for the noise
measurement
A.5 Operating conditions
A.6 Information to be recorded and reported
A.6.1 General
A.6.2 General agglomerator data
A.6.3 Agglomerator chamber data
A.6.4 Standards
A.6.5 Noise data
A.6.6 Specified test parameters
A.6.7 Installation and operating conditions
A.7 Declaration and verification of noise emission values
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Bibliography
Specifies the essential safety requirements applicable to the design and construction of agglomerators used to densify plastic scrap, reducing its size and/or volume.
| DocumentType |
Standard
|
| PublisherName |
Osterreichisches Normungsinstitut/Austrian Standards
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| EN 12012-4:2006+A1:2008 | Identical |
| NS EN 12012-4 : 2006 + A1 2008 | Identical |
| I.S. EN 12012-4:2006 | Identical |
| BS EN 12012-4 : 2006 | Identical |
| SN EN 12012-4 : 2007 + A1 2008 | Identical |
| DIN EN 12012-4:2010-01 | Identical |
| NBN EN 12012-4 : 2006 + A1 2008 | Identical |
| NEN EN 12012-4 : 2006 + A1 2008 | Identical |
| UNI EN 12012-4 : 2008 | Identical |
| NF EN 12012-4 : 2007 + A1 2008 | Identical |
| UNE-EN 12012-4:2007 | Identical |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| ONORM EN ISO 13857 : 2008 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER LIMBS |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.