MIL-DTL-5070 Revision F:2006
Current
Current
The latest, up-to-date edition.
Adapter, Hose to Tube, Pipe and Flange, Reusable - Hydraulic, Fuel, and Oil Lines, General Specification for
Available format(s)
PDF
Published date
12-10-2006
Publisher
US$20.00
Excluding Tax where applicable
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
APPENDIX A
Specifies general requirements for adapter, hose to tube, pipe, and flange, reusable - hydraulic, fuel, and oil lines.
| DevelopmentNote |
Supersedes MIL A 5070 (D) (10/2000)
|
| DocumentType |
Standard
|
| Pages |
157
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Current
|
This specification covers general requirements for adapter, hose to tube, pipe, and flange, reusable - hydraulic, fuel, and oil lines.
| MS24587 Revision E:2007 | Adapter Assembly, Straight, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27229 Revision C:2015 | Flange Nipple Assembly 45 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27225 Revision C:2007 | Nipple Assembly 45 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MIL-DTL-8795-1 Base Document:2007 | Hose Assembly, Reusable, Hydraulic, Fuel, and Oil Resistant, 3/16 Inch through 3 Inch Tube Sizes |
| MS27231 Revision B:2007 | Straight Flange Nipple Assembly, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27227 Revision C:2015 | Flange Nipple Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27235 Revision D:2007 | Elbow Tube, 45 Degrees |
| MS27224 Revision B:2007 | Swivel Nut Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines 1/4 Inch Through 2 1/2 Inch Tube Sizes |
| MIL-DTL-8795 Revision G:2014 | Hose Assemblies, Elastomeric, Hydraulic, Fuel, Coolant, and Oil Resistant, General Specification for |
| MS24588 Revision C:2007 | Nipple, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines, 3/16 through 3/4 Inch Tubing Sizes |
| MS27238 Revision B:2007 | Wire, Nut Retaining, Designed for Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27237 Revision F:2007 | Shoulder, Swivel Flange, Adapter, Hose to Tube, Hydraulic Fuel and Oil Lines, 1/2 Through 3 Inches Tubing Sizes |
| MIL-DTL-8794 Revision F:2007 | Hose, Synthetic Rubber - Hydraulic Fluid, Fuel, Coolant, and Oil Resistant, General Specification for |
| MS27232 Revision B:2007 | Straight Flange Assembly Adapter, Hose to Flange, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27236 Revision B:2007 | Shoulder - Designed for 45 Degrees and 90 Degrees Swivel Nut, Hose to Tube Adapters, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27239 Revision E:2007 | Nipple, Straight, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines, 1/4 through 4 Inch Tube Sizes |
| MS27228 Revision B:2007 | Flange Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MS27234 Revision C:2007 | Elbow Tube, 90 Degrees |
| MS28746 Revision E:2007 | Fitting End - Hose, Swivel, Detachable, 45 Degrees Flange, 4 Bolt |
| MS24591 Revision D:2007 | Socket, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines, 1 through 2 Inches Tubing Sizes |
| MS27230 Revision B:2007 | Flange Assembly 45 Degrees, Adapter, Hose to Tube, Reusable, Fuel and Oil Lines |
| MIL-DTL-5070-2 Base Document:2007 | Nipple Assembly 45 Degrees, Adapter, Hose to Tube, Reusable, Brazeless, One-Piece Design, Hydraulic, Fuel and Oil Lines, 1/4 through 2 Inch Tube Sizes |
| MS24590 Revision C:2007 | Socket, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines, 3/16 through 3/4 Inch Tubing Sizes |
| MS27223 Revision C:2007 | Nipple Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines 1/4 Inch through 2 Inch Tube Sizes |
| MS24589 Revision C:2007 | Nipple, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines, 1 through 2 Inches Tubing Sizes |
| MIL-DTL-5070-1 Base Document:2007 | Nipple Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Brazeless, One-Piece Design, Hydraulic, Fuel and Oil Lines, 1/4 through 2 Inch Tube Sizes |
| MS27226 Revision B:2007 | Swivel Nut Assembly 45 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| SAE AMS5689F | Steel, Corrosion and Heat Resistant, Wire 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated |
| MS27236 Revision B:2007 | Shoulder - Designed for 45 Degrees and 90 Degrees Swivel Nut, Hose to Tube Adapters, Reusable, Hydraulic, Fuel and Oil Lines |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| SAE AMS5645S | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (321) Solution Heat Treated |
| SAE AMSQQA225/9A | Aluminum Alloy 7075, Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished |
| SAE AS4841B | Fittings, 37° Internal Flare, Fluid Connection, Procurement Specification |
| SAE AMSQQP416E | Plating, Cadmium (Electrodeposited) |
| MIL-STD-130 Revision N:2007 | Identification Marking of U.S. Military Property |
| MS27238 Revision B:2007 | Wire, Nut Retaining, Designed for Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| MS24587 Revision E:2007 | Adapter Assembly, Straight, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines |
| SAE J1966_201108 | Lubricating Oils, Aircraft Piston Engine (Non-Dispersant Mineral Oil) |
| SAE AS603B | Impulse Testing of Hydraulic Hose, Tubing, and Fitting Assemblies |
| ANSI/NCSL Z540 3 : 2006(R2013) | REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT |
| MIL-PRF-5606 Revision H:2002 | Hydraulic Fluid, Petroleum Base; Aircraft, Missile, and Ordnance |
| SAE AMS6382P | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) Annealed |
| SAE AMS5643U | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
| SAE AMS5743J | Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered |
| SAE AMS5697F | Steel, Corrosion-Resistant, Wire 19Cr - 9.5Ni (SAE 30304) Solution Heat Treated |
| SAE AMSQQA200/8A | Aluminum Alloy 6061, Bar, Rod, Shapes, Tube, and Wire, Extruded A96061 |
| SAE AMSWWT700/4A | Tube, Aluminum Alloy, Drawn, Seamless, 5052 |
| SAE AMSA22771C | Aluminum Alloy Forgings, Heat Treated |
| SAE AMS4141G | Aluminum Alloy Die Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73) Solution and Precipitation Heat Treated |
| SAE AMS6381H | Steel, Mechanical Tubing 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) |
| SAE AMSWWT700/6C | Tube, Aluminum Alloy, Drawn, Seamless, 6061 |
| SAE AMS5647K | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 9.5Ni Solution Heat Treated |
| MIL-STD-889 Revision C:2016 | Galvanic Compatibility of Electrically Conductive Materials |
| SAE AMS5566M | Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr - 10Ni (304) High Pressure, Cold Drawn |
| SAE ARP908C | Torque Requirements, Installation and Qualification Test, Hose and Tube Fitting |
| MS24591 Revision D:2007 | Socket, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines, 1 through 2 Inches Tubing Sizes |
| SAE AMSQQA367D | Aluminum Alloy Forgings |
| MIL-PRF-87257 Revision C:2017 | Hydraulic Fluid, Fire Resistant; Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile |
| SAE AMS5567F | Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr - 10Ni (304) Solution Heat Treated |
| ASTM B 567 : 1998 | Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method |
| MS27235 Revision D:2007 | Elbow Tube, 45 Degrees |
| MS27237 Revision F:2007 | Shoulder, Swivel Flange, Adapter, Hose to Tube, Hydraulic Fuel and Oil Lines, 1/2 Through 3 Inches Tubing Sizes |
| MS27234 Revision C:2007 | Elbow Tube, 90 Degrees |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| SAE AMS4127J | Aluminum Alloy, Forgings and Rolled or Forged Rings (6061-T6) Solution and Precipitation Heat Treated |
| MS27224 Revision B:2007 | Swivel Nut Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines 1/4 Inch Through 2 1/2 Inch Tube Sizes |
| SAE AMS2700E | Passivation of Corrosion Resistant Steels |
| MIL-PRF-83282 Revision D:1997 | Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code Number H-537 |
| SAE AMS5639J | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 10Ni Solution Heat Treated |
| MS24590 Revision C:2007 | Socket, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines, 3/16 through 3/4 Inch Tubing Sizes |
| SAE AMS6370P | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) |
| SAE AMS6360M | Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) Normalized or Stress Relieved |
| MIL-DTL-8795 Revision G:2014 | Hose Assemblies, Elastomeric, Hydraulic, Fuel, Coolant, and Oil Resistant, General Specification for |
| MIL-DTL-8794 Revision F:2007 | Hose, Synthetic Rubber - Hydraulic Fluid, Fuel, Coolant, and Oil Resistant, General Specification for |
| MS28741 Revision K:2010 | Hose Assembly, Detachable End Fitting, Medium Pressure |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| SAE AMSS6758A | Steel, Chrome-Molybdenum (4130) Bars and Reforging Stock (Aircraft Quality) |
| SAE AMS4124E | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73, T7351) Solution Heat Treated, Stress Relieved by Stretching, and Overaged |
| SAE AMS4928V | Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes 6Al - 4V Annealed |
| SAE AMS6362G | Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) 150 ksi (1034 MPa) Tensile Strength |
| SAE AMS5557J | Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18.5Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated |
| SAE AMS6361F | Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) 125 ksi (862 MPa) Tensile Strength |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.