MIL-C-43616 Revision C:1981
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Cleaning Compounds, Aircraft Surface (S/S by A-A-59921)
Available format(s)
PDF
Published date
03-18-1981
Publisher
Superseded date
04-01-2013
Superseded by
US$20.00
Excluding Tax where applicable
Outlines two classes of aircraft surface cleaning compounds.
| DevelopmentNote |
C NOTICE 1 - Notice of Validation. C NOTICE 2 - Notice of Cancellation without Replacement. (04/2013)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| SupersededBy |
This specification covers the requirement for two classes of aircraft surface cleaning compounds.
| SAE AS85080A | Insulation Sleeving, Electrical, Shrinkable Without Heat, General Specification For |
| DEFSTAN 61-12(PT0)/3(2011) : 2011 | WIRES, CORDS AND CABLES ELECTRICAL METRIC UNITS - PART 0: GENERAL REQUIREMENTS AND TEST METHODS GENERIC SPECIFICATION |
| MIL-C-85028 Base Document:1977 | Connector, Electrical, Rectangular, Individual Contact Sealing, Polarized Center Jackscrew, General Specification for (S/S by SAE-AS85028) |
| MIL W 18723 : D | WAX, AIRCRAFT, WATERPROOF, SOLVENT TYPE |
| DEFSTAN 61-12(PT21)/2(1985) : 1985 | WIRES, CORDS, AND CABLES, ELECTRICAL - METRIC UNITS - PART 21: WIRES AND CABLES, LIGHTWEIGHT, EXTRUDED INSULATION, 135 DEGREES TIN PLATED, AND 150 DEGREES SILVER PLATED CONDUCTORS |
| MIL C 3702 : B | CABLE, POWER, ELECTRICAL, IGNITION, HIGH TENSION |
| MIL-C-87936 Revision A:1985 | Cleaning Compounds, Aircraft Exterior Surfaces, Water Dilutable (S/S by MIL-C-87937) |
| DEFSTAN 61-12(PT0)/2(2006) : 2006 | WIRES, CORDS AND CABLES, ELECTRICAL - PART 0: GENERAL REQUIREMENTS AND TEST METHODS - GENERAL SPECIFICATION |
| DEFSTAN 61-12(PT26)/3(2001) : 2001 | WIRES, CORDS AND CABLES, ELECTRICAL - PART 26: WIRES AND CABLES ELECTRICAL, DUAL EXTRUDED INSULATION TYPE OLEFIN/VINYLIDEN-FLUORIDE AND SCREENED AND JACKETED - SECTIONAL SPECIFICATION |
| SAE AS85028C | Connector, Electrical, Rectangular, Individual Contact Sealing, Polarized Center Jackscrew, General Specification For |
| MIL-C-22751 Revision D:1971 | Coating System, Epoxy-Polyamide, Chemical and Solvent Resistant: Process for Application of (No S/S Document) |
| TT-R-248 Revision B:1981 | REMOVER, PAINT AND LACQUER, SOLVENT TYPE |
| DEFSTAN 61-12(PT24)/1(1987) : 1987 AMD 2 | WIRES, CORDS AND CABLES, ELECTRICAL - METRIC UNITS - WIRES AND CABLES, LIGHTWEIGHT, TAPED INSULATION, 150 DEG C SILVER PLATED AND 260 DEG C NICKEL PLATED CONDUCTORS |
| MIL-STD-808 Revision A:1983 | FINISH, MATERIALS AND PROCESSES FOR CORROSION PREVENTION AND CONTROL IN SUPPORT EQUIPMENT |
| DEFSTAN 61-12(PT33)/5(2005) : 2005 | WIRES, CORDS AND CABLES ELECTRICAL - PART 33: AIRFRAME WIRES AND CABLES IN THE TEMPERATURE CATEGORIES OF 135 DEGREES C, 200 DEGREES C AND 260 DEGREES C |
| DEFSTAN 61-12(PT33)/4(2001) : 2001 AMD 4 2004 | WIRES, CORDS AND CABLES, ELECTRICAL - PART 33: AIRFRAME WIRES AND CABLES IN THE TEMPERATURE CATEGORIES OF 135 DEGREES C, 150 DEGREES C, 200 DEGREES C AND 260 DEGREES C - SECTIONAL SPECIFICATION |
| ADS-13F-HDBK : 1997 | AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES |
| MIL-R-81294 Revision D:1990 | Remover, Paint, Epoxy, Polysulfide, and Polyurethane Systems |
| MIL F 14072 : D | FINISHES FOR GROUND BASED ELECTRONIC EQUIPMENT |
| FED-STD-313 Revision D:1996 | Material Safety Data, Transportation Data, and Disposal Data for Hazardous Materials Furnished to Government Activities |
| PPP-C-96 Revision E:1992 | Cans, Metal, 28 Gage and Lighter |
| ASTM D 98 : 2015 : REDLINE | Standard Specification for Calcium Chloride |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| PPP-B-636 Revision J:1981 | Boxes, Shipping, Fiberboard (S/S by ASTM-D1974 and ASTM-D5118) |
| MIL-STD-147 Revision E:2008 | Palletized Unit Loads |
| MIL-M-3171 Revision C:1966 | Magnesium Alloy, Processes for Pretreatment and Prevention of Corrosion on (S/S by SAE-AMS-M-3171) |
| QQ-A-250-2 Revision E:1983 | Aluminum Alloy 3003, Plate and Sheet (See Notice 3 for Replacement Information) |
| PPP-D-705 Revision E:1994 | Drum, Shipping and Storage: Steel, 16 and 30 Gallon Capacity (Future acquisitions for this material should refer to MIL-DTL-6054) |
| MIL P 23377 : G | PRIMER COATING, EPOXY, HIGH SOLIDS |
| MIL-T-9046 Revision J:1983 | TITANIUM AND TITANIUM ALLOY, SHEET, STRIP AND PLATE (S/S BY SAE-AMS-T-9046) |
| FED-STD-406 Revision A:1982 | PLASTICS: METHODS OF TESTING (S/S BY - SEE CANCELLATION NOTICE FOR RECOMMENDED SUPERSEDING ASTM TEST METHODS) |
| MIL-C-8514 Revision C:1967 | Coating Compound, Metal Retreatment, Resin-Acid (ASG) |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| PPP-D-729 Revision E:1977 | Drums, Shipping and Storage, Steel, 55-Gallon (208 Liters) |
| MIL-L-6082 Revision E:1990 | Lubricating Oil, Aircraft Piston Engine (Non-Dispersant Mineral Oil) (S/S by SAE-J1966) |
| QQ-M-44 Revision B:1964 | Magnesium Alloy Plate and Sheet ( AZ31B) (S/S byAMS4375, AMS4377 and AMS4376) |
| MIL-L-19537 Revision C:1965 | Lacquer: Acrylic-Nitrocellulose Gloss (for Aircraft use) (S/S by MIL-L-81352) |
| PPP-P-704 Revision E:1981 | Pails, Metal: (Shipping, Steel, 1 through 12 Gallons) |
| QQ-P-416 Revision F:1991 | Plating, Cadmium (Electrodeposited) (S/Sby SAE-AMS-QQ-P-416) |
| FED-STD-791 Revision D:2007 | Testing Method of Lubricants, Liquid Fuels, and Related Products |
| MIL-STD-105 Revision E:1989 | Sampling Procedures and Tables for Inspection by Attributes (See Notice 3 for Replacement Information) |
| MIL-C-83286 Revision B:1973 | Coating, Urethane, Aliphatic Isocyanate, for Aerospace Applications (S/S by MIL-C-85285 S/S by MIL-PRF-85285) |
| MIL P 5425 : D | PLASTIC, SHEET, ACRYLIC, HEAT RESISTANT |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.Are you sure?
Logging out.