ISO 6162-1:2012
Current
Current
The latest, up-to-date edition.
Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
French, English
Published date
12-14-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 6162-1:2012 gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at pressures of 3,5 MPa (35 bar ) to 35 MPa (350 bar). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals.
ISO 6162-1:2012 also recognizes the need to accommodate metric screw fasteners (type 1), as well as to provide a means to use existing inch screw fasteners (type 2).
These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.
Surges of pressure higher than the nominal ratings will reduce the ability of the flange connections to retain the hydraulic fluid. This needs to be taken into account in the design of the hydraulic system.
| Committee |
ISO/TC 131/SC 4
|
| DevelopmentNote |
Together with ISO 6162-2 supersedes ISO 6162. (12/2002) Supersedes ISO/DIS 6162-1. (12/2012)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| BS ISO 6162-1:2012 | Identical |
| NF ISO 6162-1 : 2013 | Identical |
| NEN ISO 6162-1 : 2012 | Identical |
| DIN ISO 6162-1:2006-02 | Identical |
| SN ISO 6162-1 : 2005 CORR 2005 | Identical |
| 16/30328245 DC : 0 | BS ISO 6164 - HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 10 TO 80 |
| 04/30098195 DC : DRAFT JUL 2004 | ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES |
| BS ISO 6022:2006 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 25M Pa (250 bar) series |
| BS ISO 10946:1999 | Hydraulic fluid power. Gas-loaded accumulators with separator. Selection of preferred hydraulic ports |
| 06/30128831 DC : DRAFT MAR 2006 | ISO 6020-1 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES |
| UNE-EN ISO 4413:2011 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| ISO 17165-1:2007 | Hydraulic fluid power — Hose assemblies — Part 1: Dimensions and requirements |
| UNE-EN ISO 19879:2010 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
| EN ISO 19879:2010 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
| DIN ISO 6022:2008-06 | HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES |
| DIN EN ISO 16330:2004-08 | Reciprocating positive displacement pumps and pump units - Technical requirements (ISO 16330:2003) |
| 09/30202316 DC : 0 | BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES |
| BS ISO 6020-1:2007 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Medium series |
| BS EN ISO 4413:2010 | Hydraulic fluid power. General rules and safety requirements for systems and their components |
| BS ISO 6020-2:2015 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Compact series |
| SAE J 846 : 2015 | CODING SYSTEMS FOR IDENTIFICATION OF FLUID CONDUCTORS AND CONNECTORS |
| 07/30163202 DC : 0 | BS ISO 12151-3 - CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
| BS ISO 6020-3:2015 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Compact series with bores from 250 mm to 500 mm |
| ISO 4081:2016 | Rubber hoses and tubing for cooling systems for internal-combustion engines Specification |
| DIN EN ISO 4413:2011-04 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| SAE J 515 : 2015 | SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS |
| ISO 6164:1994 | Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar) |
| SAE J 518/3 : 2015 | HYDRAULIC FLANGE CLAMPS, 2-SCREW FLANGE CONNECTION TO BE USED WITH SAE J518-1, (CODE 61) CONNECTIONS WHERE ONLY LOW PRESSURE IS REQUIRED |
| ISO 19859:2016 | Gas turbine applications Requirements for power generation |
| I.S. EN ISO 19879:2010 | METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
| SAE J 2551/3 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 3: PROCUREMENT |
| UNI ISO 12151-3 : 2012 | CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
| BS ISO 12151-3:2010 | Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| BS ISO 16874:2004 | Hydraulic fluid power. Identification of manifold assemblies and their components |
| BS ISO 17165-1:2007 | Hydraulic fluid power. Hose assemblies Dimensions and requirements |
| ISO 6022:2006 | Hydraulic fluid power — Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series |
| 09/30193685 DC : 0 | BS ISO 4081 - RUBBER HOSES AND TUBING FOR COOLING SYSTEMS FOR INTERNAL-COMBUSTION ENGINES - SPECIFICATION |
| SAE J 2551/1 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 1: DESIGN AND FABRICATION |
| SAE J 1677 : 2016 | TESTS AND PROCEDURES FOR CARBON STEEL AND HIGH STRENGTH LOW ALLOY STEEL TUBING |
| SAE J 518/2 : 2017 | HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 2: 42 MPA (CODE 62) |
| ISO 6020-3:2015 | Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 3: Compact series with bores from 250 mm to 500 mm |
| ISO 6020-2:2015 | Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series |
| 03/110806 DC : DRAFT JUNE 2003 | BS ISO 19879 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
| 14/30274168 DC : 0 | BS ISO 6020-3 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 3: COMPACT SERIES WITH BORES FROM 250 MM TO 500 MM |
| SAE J 2551/2 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 2: GENERAL SPECIFICATIONS AND PERFORMANCE REQUIREMENTS |
| PD ISO/TS 11672:2016 | Connectors for fluid power and general use. Designation and nomenclature |
| UNI ISO 17165-1 : 2012 | HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS |
| BS ISO 4081:2016 | Rubber hoses and tubing for cooling systems for internal-combustion engines. Specification |
| DIN ISO 6020-1:2010-07 | Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series - Part 1: Medium series (ISO 6020-1:2007) |
| SAE J 518/1 : 2013 | HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 1: 3.5 MPA TO 35 MPA (CODE 61) |
| SAE J 2593 : 2015 | INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS |
| ISO 6020-1:2007 | Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 1: Medium series |
| ISO 16874:2004 | Hydraulic fluid power Identification of manifold assemblies and their components |
| BS EN ISO 16330:2003 | Reciprocating positive displacement pumps and pump units. Technical requirements |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| BS ISO 19859:2016 | Gas turbine applications. Requirements for power generation |
| ISO 16330:2003 | Reciprocating positive displacement pumps and pump units Technical requirements |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| EN ISO 16330:2003 | Reciprocating positive displacement pumps and pump units - Technical requirements (ISO 16330:2003) |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| 04/30098199 DC : DRAFT JUL 2004 | ISO 6022 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES |
| SAE J 1065 : 2016 | NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING |
| SAE J 2614 : 2018 | WELDED AND COLD-DRAWN, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, FLARING, COLD FORMING, WELDING AND BRAZING |
| 14/30284271 DC : 0 | BS ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES |
| ISO 12151-3:2010 | Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| SAE J 2551 : 2013 | RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON AND ALLOY STEEL TUBING APPLICATIONS |
| UNI EN ISO 19879 : 2011 | METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
| PD ISO/TS 17165-2:2013 | Hydraulic fluid power. Hose assemblies Practices for hydraulic hose assemblies |
| NF EN ISO 4413 : 2011 | HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS |
| NF ISO 12151-3 : 2010 | CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
| DIN EN ISO 19879:2011-01 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
| 14/30244780 DC : 0 | BS ISO 19859 - GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION |
| BS EN ISO 19879:2010 | Metallic tube connections for fluid power and general use. Test methods for hydraulic fluid power connections |
| DIN ISO 12151-3:2012-08 | Connections for hydraulic fluid power and general use - Hose fittings - Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends (ISO 12151-3:2010) |
| ISO 68-2:1998 | ISO general purpose screw threads — Basic profile — Part 2: Inch screw threads |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| SAE J 429 : 2014 | MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS |
| ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
| ISO 4017:2014 | Fasteners Hexagon head screws Product grades A and B |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| ISO 4762:2004 | Hexagon socket head cap screws |
| ISO 5864:1993 | ISO inch screw threads Allowances and tolerances |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| SAE J 515 : 2015 | SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS |
| ISO 12151-3:2010 | Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| ISO 7089:2000 | Plain washers Normal series Product grade A |
| ISO 68-1:1998 | ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| ISO 6164:1994 | Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar) |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 725:2009 | ISO inch screw threads Basic dimensions |
| ASME B18.3 : 2012 | SOCKET CAP, SHOULDER, SET SCREWS, AND HEX KEYS (INCH SERIES) |
| ISO 273:1979 | Fasteners — Clearance holes for bolts and screws |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| ISO 10763:1994 | Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures |
| ISO 3601-1:2012 | Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes |
| ASTM A 574 : 2017 : REDLINE | Standard Specification for Alloy Steel Socket-Head Cap Screws |
| ISO 13715:2017 | Technical product documentation — Edges of undefined shape — Indication and dimensioning |
| ISO 3601-3:2005 | Fluid power systems O-rings Part 3: Quality acceptance criteria |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 263:1973 | ISO inch screw threads General plan and selection for screws, bolts and nuts Diameter range 0,06 to 6 in |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.