ISO 5167-4:2003
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 4: Venturi tubes
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Withdrawn date
06-16-2022
Superseded by
Language(s)
English, French
Published date
02-24-2003
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 5167-4:2003 specifies the geometry and method of use (installation and operating conditions) of Venturi tubes when they are inserted in a conduit running full to determine the flowrate of the fluid flowing in the conduit.
ISO 5167-4:2003 also provides background information for calculating the flow-rate and is applicable in conjunction with the requirements given in ISO 5167-1.
ISO 5167-4:2003 is applicable only to Venturi tubes in which the flow remains subsonic throughout the measuring section and where the fluid can be considered as single-phase. In addition, each of these devices can only be used within specified limits of pipe size, roughness, diameter ratio and Reynolds number. ISO 5167-4:2003 is not applicable to the measurement of pulsating flow. It does not cover the use of Venturi tubes in pipes sized less than 50 mm or more than 1 200 mm, or for where the pipe Reynolds numbers are below 20 000.
ISO 5167-4:2003 deals with the three types of classical Venturi tubes: cast, machined and rough welded sheet-iron.
A Venturi tube is a device which consists of a convergent inlet connected to a cylindrical throat which is in turn connected to a conical expanding section called the "divergent". The differences between the values of the uncertainty of the discharge coefficient for the three types of classical Venturi tube show, on the one hand, the number of results available for each type of classical Venturi tube and, on the other hand, the more or less precise definition of the geometric profile. The values are based on data collected many years ago. Venturi nozzles (and other nozzles) are dealt with in ISO 5167-3.
| DevelopmentNote |
Supersedes ISO/DIS 5167-4 (02/2003) Together with ISO 5167-1, ISO 5167-2 and ISO 5167-3 supersedes the 1st Edition of ISO 5167-1 (03/2003)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN ISO 5167-4 : 2003 | Identical |
| JIS Z 8762-4:2007 | Identical |
| NF EN ISO 5167-4 : 2003 | Identical |
| UNE-EN ISO 5167-4:2003 | Identical |
| NBN EN ISO 5167-4 : 2003 | Identical |
| NEN EN ISO 5167-4 : 2003 | Identical |
| NS EN ISO 5167-4 : 1ED 2003 | Identical |
| I.S. EN ISO 5167-4:2003 | Identical |
| PN EN ISO 5167-4 : 2005 | Identical |
| SN EN ISO 5167-4 : 2003 | Identical |
| UNI EN ISO 5167-4 : 2004 | Identical |
| BIS IS 14615-4:2018 | Identical |
| BS EN ISO 5167-4:2003 | Identical |
| EN ISO 5167-4:2003 | Identical |
| DIN EN ISO 5167-4:2004-01 | Identical |
| ISO/TR 9824:2007 | Hydrometry Measurement of free surface flow in closed conduits |
| 17/30326671 DC : 0 | BS ISO 27919-1 - CARBON DIOXIDE CAPTURE - PART 1: PERFORMANCE EVALUATION METHODS FOR POST-COMBUSTION CO[2] CAPTURE INTEGRATED WITH A POWER PLANT |
| BS EN 16445:2013 | Ventilation for buildings. Air diffusion. Aerodynamic testing and rating for mixed flow application: non-isothermal procedure for cold jet |
| PD ISO/TR 9464:2008 | Guidelines for the use of ISO 5167:2003 |
| DIN EN ISO 18854:2015-08 | SMALL CRAFT - RECIPROCATING INTERNAL COMBUSTION ENGINES EXHAUST EMISSION MEASUREMENT - TEST-BED MEASUREMENT OF GASEOUS AND PARTICULATE EXHAUST EMISSIONS (ISO 18854:2015) |
| ISO 8178-1:2017 | Reciprocating internal combustion engines Exhaust emission measurement Part 1: Test-bed measurement systems of gaseous and particulate emissions |
| BS EN 16211:2015 | Ventilation for buildings. Measurement of air flows on site. Methods |
| PD ISO/TR 9824:2007 | Hydrometry. Measurement of free surface flow in closed conduits |
| CSA C748 : 2013 | PERFORMANCE OF DIRECT-EXPANSION (DX) GROUND-SOURCE HEAT PUMPS |
| I.S. EN ISO 14644-3:2006 | CLEANROOMS AND ASSOCIATED CONTROLLED ENVIRONMENTS - PART 3: TEST METHODS |
| DIN EN 13141-6:2015-02 | VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING |
| I.S. EN 13141-6:2014 | VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING |
| ONORM EN 1366-10 : 2011 | FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 10: SMOKE CONTROL DAMPERS |
| UNI EN 16445 : 2013 | VENTILATION FOR BUILDINGS - AIR DIFFUSION - AERODYNAMIC TESTING AND RATING FOR MIXED FLOW APPLICATION: NON-ISOTHERMAL PROCEDURE FOR COLD JET |
| PD ISO/TR 26762:2008 | Natural gas. Upstream area. Allocation of gas and condensate |
| 11/30233217 DC : 0 | BS EN 1751 - VENTILATION FOR BUILDINGS - AIR TERMINAL DEVICES - AERODYNAMIC TESTING OF DAMPER AND VALVES |
| ISO/TR 12748:2015 | Natural Gas Wet gas flow measurement in natural gas operations |
| 16/30334068 DC : 0 | BS ISO 8178-4 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 4: STEADY-STATE TEST CYCLES FOR DIFFERENT ENGINE APPLICATIONS |
| PD IEC/TS 62282-7-1:2017 | Fuel cell technologies Test methods. Single cell performance tests for polymer electrolyte fuel cells (PEFC) |
| 05/30098143 DC : DRAFT OCT 2005 | ISO 2186 - FLUID FLOW IN CLOSED CONDUITS - CONNECTIONS FOR PRESSURE SIGNAL TRANSMISSIONS BETWEEN PRIMARY AND SECONDARY ELEMENTS |
| 14/30289271 DC : 0 | BS EN 16211 - VENTILATION FOR BUILDINGS - MEASUREMENT OF AIR FLOWS ON SITE - METHODS |
| 08/30188933 DC : DRAFT SEP 2008 | BS EN 15854 - VENTILATION FOR BUILDINGS - AIR DIFFUSION - AERODYNAMIC TESTING AND RATING FOR MIXING FLOW APPLICATION - NON-ISOTHERMAL PROCEDURE FOR A COLD JET |
| 14/30230935 DC : 0 | BS EN ISO 4126-11 - SAFETY DEVICES FOR PROTECTION AGAINST EXCESSIVE PRESSURE - PART 11: PERFORMANCE TESTING |
| PD ISO/TR 12748:2015 | Natural Gas. Wet gas flow measurement in natural gas operations |
| BS ISO 2186:2007 | Fluid flow in closed conduits. Connections for pressure signal transmissions between primary and secondary elements |
| PREN 1539 : DRAFT 2012 | DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS |
| I.S. EN ISO 18854:2015 | SMALL CRAFT - RECIPROCATING INTERNAL COMBUSTION ENGINES EXHAUST EMISSION MEASUREMENT - TEST-BED MEASUREMENT OF GASEOUS AND PARTICULATE EXHAUST EMISSIONS (ISO 18854:2015) |
| UNE-EN 50399:2012 | Common test methods for cables under fire conditions - Heat release and smoke production measurement on cables during flame spread test - Test apparatus, procedures, results |
| ONORM EN 1822-5 : 2011 | HIGH EFFICIENCY AIR FILTERS (EPA, HEPA AND ULPA) - PART 5: DETERMINING THE EFFICIENCY OF FILTER ELEMENTS |
| DIN EN 1751:2014-06 | Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves |
| DIN EN ISO 5167-1:2004-01 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| I.S. EN ISO 5167-1:2003 | MEASUREMENT OF FLUID FLOW BY MEANS OF PRESSURE DIFFERENTIAL DEVICES INSERTED IN CIRCULAR CROSS-SECTION CONDUITS RUNNING FULL - PART 1: GENERAL PRINCIPLES AND REQUIREMENTS |
| I.S. EN 1751:2014 | VENTILATION FOR BUILDINGS - AIR TERMINAL DEVICES - AERODYNAMIC TESTING OF DAMPER AND VALVES |
| I.S. EN ISO 9906:2012 | ROTODYNAMIC PUMPS - HYDRAULIC PERFORMANCE ACCEPTANCE TESTS - GRADES 1, 2 AND 3 (ISO 9906:2012) |
| DIN EN 1751:1999-01 | VENTILATION FOR BUILDINGS - AIR TERMINAL DEVICES - AERODYNAMIC TESTING OF DAMPERS AND VALVES |
| VDI 2048 Blatt 1:2000-10 | Uncertainties of measurements at acceptance tests for energy conversion and power plants - Fundamentals |
| VDI 2048 Blatt 3:2012-05 | Uncertainties of measurement during acceptance tests on energy-conversion and power plants - Examples, especially preparation of acceptance tests of a gas and steam power plant |
| UNE-EN 16211:2016 | Ventilation for buildings - Measurement of air flows on site - Methods |
| 16/30326493 DC : 0 | BS EN ISO 14644-3 - CLEANROOMS AND ASSOCIATED CONTROLLED ENVIRONMENTS - PART 3: TEST METHODS |
| 12/30258755 DC : 0 | BS EN 1539 - DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS |
| BS ISO 8178-1:2017 | Reciprocating internal combustion engines. Exhaust emission measurement Test-bed measurement systems of gaseous and particulate emissions |
| I.S. EN 50399:2011 | COMMON TEST METHODS FOR CABLES UNDER FIRE CONDITIONS - HEAT RELEASE AND SMOKE PRODUCTION MEASUREMENT ON CABLES DURING FLAME SPREAD TEST - TEST APPARATUS, PROCEDURES, RESULTS |
| UNI EN 14277 : 2008 | VENTILATION FOR BUILDINGS - AIR TERMINAL DEVICES - METHOD FOR AIRFLOW MEASUREMENT BY CALIBRATED SENSORS IN OR CLOSE TO ATD/PLENUM BOXES |
| 11/30253126 DC : 0 | BS EN 16282-9 - EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION OF COMMERCIAL KITCHENS - PART 9: CAPTURE AND CONTAINMENT PERFORMANCE OF EXTRACTION SYSTEMS - TEST METHODS |
| API MPM CH14.10 : 2007 : R2012 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 14: NATURAL GAS FLUIDS MEASUREMENT - SECTION 10: MEASUREMENT OF FLOW TO FLARES |
| UNE-EN ISO 18854:2015 | Small craft - Reciprocating internal combustion engines exhaust emission measurement - Test-bed measurement of gaseous and particulate exhaust emissions (ISO 18854:2015) |
| API MPM CH14.10: 2007 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 14: NATURAL GAS FLUIDS MEASUREMENT - SECTION 10: MEASUREMENT OF FLOW TO FLARES |
| 02/706744 DC : DRAFT MAY 2002 | ISO/DIS 8178-1 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 1: TEST-BED MEASUREMENT OF GASEOUS AND PARTICULATE EXHAUST EMISSIONS |
| 14/30303765 DC : 0 | BS EN 16282-9 - EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION IN COMMERCIAL KITCHENS - PART 9: CAPTURE AND CONTAINMENT PERFORMANCE OF EXTRACTION SYSTEMS - TEST METHODS |
| BS EN 50399:2011 | Common test methods for cables under fire conditions. Heat release and smoke production measurement on cables during flame spread test. Test apparatus, procedures, results |
| PREN 1751 : DRAFT 2011 | VENTILATION FOR BUILDINGS - AIR TERMINAL DEVICES - AERODYNAMIC TESTING OF DAMPER AND VALVES |
| ONORM EN 1366-12 : 2014 | FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 12: NON-MECHANICAL FIRE BARRIER FOR VENTILATION DUCTWORK |
| ISO 16345:2014 | Water-cooling towers — Testing and rating of thermal performance |
| API 551 : 2016 | PROCESS MEASUREMENT |
| ISO 29463-3:2011 | High-efficiency filters and filter media for removing particles in air — Part 3: Testing flat sheet filter media |
| DIN EN ISO 14644-3:2006-03 | CLEANROOMS AND ASSOCIATED CONTROLLED ENVIRONMENTS - PART 3: TEST METHODS |
| UNE-EN 1751:2014 | Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves |
| BS EN ISO 9906:2012 | Rotodynamic pumps. Hydraulic performance acceptance tests. Grades 1, 2 and 3 |
| DIN EN ISO 9906:2013-03 | ROTODYNAMIC PUMPS - HYDRAULIC PERFORMANCE ACCEPTANCE TESTS - GRADES 1, 2 AND 3 (ISO 9906:2012) |
| ONORM EN 1366-1 : 2014 | FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 1: VENTILATION DUCTS |
| ISO 8178-1:2020 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement systems of gaseous and particulate emissions |
| UNI EN 1751 : 2014 | VENTILATION FOR BUILDINGS - AIR TERMINAL DEVICES - AERODYNAMIC TESTING OF DAMPER AND VALVES |
| UNI EN ISO 9906 : 2012 | ROTODYNAMIC PUMPS - HYDRAULIC PERFORMANCE ACCEPTANCE TESTS - GRADES 1, 2 AND 3 |
| ISO/TR 15377:2018 | Measurement of fluid flow by means of pressure-differential devices — Guidelines for the specification of orifice plates, nozzles and Venturi tubes beyond the scope of ISO 5167 |
| ISO 29463-2:2011 | High-efficiency filters and filter media for removing particles in air — Part 2: Aerosol production, measuring equipment and particle-counting statistics |
| ISO 2186:2007 | Fluid flow in closed conduits — Connections for pressure signal transmissions between primary and secondary elements |
| DIN EN 16445:2013-05 | VENTILATION FOR BUILDINGS - AIR DIFFUSION - AERODYNAMIC TESTING AND RATING FOR MIXED FLOW APPLICATION: NON-ISOTHERMAL PROCEDURE FOR COLD JET |
| ISO 8178-4:2017 | Reciprocating internal combustion engines Exhaust emission measurement Part 4: Steady-state and transient test cycles for different engine applications |
| BS ISO 8178-4:2017 | Reciprocating internal combustion engines. Exhaust emission measurement Steady-state and transient test cycles for different engine applications |
| DIN EN 16211:2015-09 | Ventilation for buildings - Measurement of air flows on site - Methods |
| I.S. EN 16211:2015 | VENTILATION FOR BUILDINGS - MEASUREMENT OF AIR FLOWS ON SITE - METHODS |
| PD ISO/TR 12767:2007 | Measurement of fluid flow by means of pressure differential devices. Guidelines on the effect of departure from the specifications and operating conditions given in ISO 5167 |
| ISO/TR 9464:2008 | Guidelines for the use of ISO 5167:2003 |
| IEC TS 62282-7-1:2017 | Fuel cell technologies - Part 7-1: Test methods - Single cell performance tests for polymer electrolyte fuel cells (PEFC) |
| ISO 9906:2012 | Rotodynamic pumps — Hydraulic performance acceptance tests — Grades 1, 2 and 3 |
| BS EN ISO 14644-3:2005 | Cleanrooms and associated controlled environments Test methods |
| ISO 18854:2015 | Small craft — Reciprocating internal combustion engines exhaust emission measurement — Test-bed measurement of gaseous and particulate exhaust emissions |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| UNE-EN 13141-6:2015 | Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling |
| ONORM EN 13053 : 2011 | VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS |
| BS EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full General principles and requirements |
| BS EN 14277:2006 | Ventilation for buildings. Air terminal devices. Method for airflow measurement by calibrated sensors in or close to ATD/plenum boxes |
| EN 16211:2015 | Ventilation for buildings - Measurement of air flows on site - Methods |
| EN 14277:2006 | Ventilation for buildings - Air terminal devices - Method for airflow measurement by calibrated sensors in or close to ATD/plenum boxes |
| EN 1751:2014 | Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN ISO 9906:2012 | Rotodynamic pumps - Hydraulic performance acceptance tests - Grades 1, 2 and 3 (ISO 9906:2012) |
| EN 16445:2013 | Ventilation for buildings - Air diffusion - Aerodynamic testing and rating for mixed flow application: non-isothermal procedure for cold jet |
| EN ISO 18854:2015 | Small craft - Reciprocating internal combustion engines exhaust emission measurement - Test-bed measurement of gaseous and particulate exhaust emissions (ISO 18854:2015) |
| EN ISO 14644-3:2005 | Cleanrooms and associated controlled environments - Part 3: Test methods (ISO 14644-3:2005) |
| 10/30240340 DC : 0 | BS EN 16211 - VENTILATION FOR BUILDINGS - MEASUREMENT OF AIR FLOWS ON SITE - METHODS |
| BS EN ISO 18854:2015 | Small craft. Reciprocating internal combustion engines exhaust emission measurement. Test-bed measurement of gaseous and particulate exhaust emissions |
| BS ISO 16345:2014 | Water-cooling towers. Testing and rating of thermal performance |
| PD ISO/TR 11583:2012 | Measurement of wet gas flow by means of pressure differential devices inserted in circular cross-section conduits |
| 16/30334062 DC : 0 | BS ISO 8178-1 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 1: TEST-BED MEASUREMENT SYSTEMS OF GASEOUS AND PARTICULATE EMISSIONS |
| 13/30284324 DC : 0 | BS EN ISO 18854 - SMALL CRAFT - RECIPROCATING INTERNAL COMBUSTION ENGINES EXHAUST EMISSION MEASUREMENT - TEST-BED MEASUREMENT OF GASEOUS AND PARTICULATE EXHAUST EMISSIONS |
| I.S. EN 16445:2013 | VENTILATION FOR BUILDINGS - AIR DIFFUSION - AERODYNAMIC TESTING AND RATING FOR MIXED FLOW APPLICATION: NON-ISOTHERMAL PROCEDURE FOR COLD JET |
| ISO/TR 26762:2008 | Natural gas — Upstream area — Allocation of gas and condensate |
| ISO/TR 11583:2012 | Measurement of wet gas flow by means of pressure differential devices inserted in circular cross-section conduits |
| ISO 14644-3:2005 | Cleanrooms and associated controlled environments Part 3: Test methods |
| BS EN 13141-6:2014 | Ventilation for buildings. Performance testing of components/products for residential ventilation Exhaust ventilation system packages used in a single dwelling |
| BS EN 1751:2014 | Ventilation for buildings. Air terminal devices. Aerodynamic testing of damper and valves |
| EN 13141-6:2014 | Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling |
| EN 50399 : 2011 AMD 1 2016 | COMMON TEST METHODS FOR CABLES UNDER FIRE CONDITIONS - HEAT RELEASE AND SMOKE PRODUCTION MEASUREMENT ON CABLES DURING FLAME SPREAD TEST - TEST APPARATUS, PROCEDURES, RESULTS |
| DIN EN 14277:2006-11 | Ventilation for buildings - Air terminal devices - Method for airflow measurement by calibrated sensors in or close to ATD/plenum boxes |
| ONORM EN 1751 : JUN 2014 | VENTILATION FOR BUILDINGS - AIR TERMINAL DEVICES - AERODYNAMIC TESTING OF DAMPER AND VALVES |
| EN 24006:1993 | Measurement of fluid flow in closed conduits - Vocabulary and symbols (ISO 4006:1991) |
| ISO/TR 5168:1998 | Measurement of fluid flow Evaluation of uncertainties |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| ISO/TR 3313:1998 | Measurement of fluid flow in closed conduits Guidelines on the effects of flow pulsations on flow-measurement instruments |
| ISO/TR 9464:2008 | Guidelines for the use of ISO 5167:2003 |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
| ISO 4006:1991 | Measurement of fluid flow in closed conduits — Vocabulary and symbols |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.