ISO 16422:2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Specifications
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
02-01-2024
Superseded by
Language(s)
English
Published date
02-10-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 16422:2014 specifies the requirements of pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O), for piping systems intended to be used underground or above-ground where not exposed to direct sunlight, for water mains and services, pressurized sewer systems and irrigation systems.
The piping system according to ISO 16422:2014 is intended for the conveyance of cold water under pressure, for drinking water and for general purposes up to and including 45 °C, and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bars[1].
Joints constructed of other materials should meet their own relevant standards in addition to the fitness-for-purpose requirements of ISO 16422:2014.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2
| Committee |
ISO/TC 138/SC 2
|
| DevelopmentNote |
Supersedes ISO/DIS 16422. (02/2014)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
International Organization for Standardization
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
| Standards | Relationship |
| UNE-ISO 16422:2015 | Identical |
| NEN ISO 16422 : 2014 | Identical |
| BS ISO 16422:2014 | Identical |
| DS ISO 16422 : 2014 | Identical |
| 08/30092426 DC : DRAFT JULY 2008 | BS ISO 12162 - THERMOPLASTICS MATERIALS FOR PIPES AND FITTINGS FOR PRESSURE APPLICATIONS - CLASSIFICATION, DESIGNATION COEFFICIENT, AND DESIGNATION |
| UNI EN 15014 : 2008 | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND SYSTEMS FOR WATER AND OTHER FLUIDS UNDER PRESSURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| 11/30239906 DC : 0 | BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER AND OTHER LIQUIDS UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| BS EN 15014:2007 | Plastics piping systems. Buried and above ground systems for water and other fluids under pressure. Performance characteristics for pipes, fittings and their joints |
| NBR 15750 : 2009 | PVC-O (ORIENTED UNPLASTICISED POLYVINYL CHLORIDE) PIPING SYSTEMS FOR THE CONVEYANCE OF WATER OR SEWAGE UNDER PRESSURE - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 12162:2009 | THERMOPLASTICS MATERIALS FOR PIPES AND FITTINGS FOR PRESSURE APPLICATIONS - CLASSIFICATION, DESIGNATION AND DESIGN COEFFICIENT (ISO 12162:2009) |
| ISO 17885:2015 | Plastics piping systems Mechanical fittings for pressure piping systems Specifications |
| BS EN ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications. Classification, designation and design coefficient |
| DIN EN ISO 12162:2010-04 | Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009) |
| UNI EN ISO 12162 : 2010 | THERMOPLASTICS MATERIALS FOR PIPES AND FITTINGS FOR PRESSURE APPLICATIONS - CLASSIFICATION, DESIGNATION AND DESIGN COEFFICIENT |
| EN ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009) |
| EN 15014:2007 | Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints |
| BS ISO 17885:2015 | Plastics piping systems. Mechanical fittings for pressure piping systems. Specifications |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 2507-2:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes |
| ISO 6259-2:1997 | Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI) |
| ISO 13846:2000 | Plastics piping systems End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping Test method for long-term leaktightness under internal water pressure |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 2507-1:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method |
| ISO 3127:1994 | Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method |
| ISO 161-1:1996 | Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 1452-5:2009 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 5: Fitness for purpose of the system |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| ISO 13783:1997 | Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints — Test method for leaktightness and strength while subjected to bending and internal pressure |
| ISO 13844:2015 | Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes Test method for leaktightness under negative pressure, angular deflection and deformation |
| ISO 1452-2:2009 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 2: Pipes |
| ISO 18373-1:2007 | Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature |
| ISO 1628-2:1998 | Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 2: Poly(vinyl chloride) resins |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| ISO 2531:2009 | Ductile iron pipes, fittings, accessories and their joints for water applications |
| ISO 4633:2015 | Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials |
| ISO 9852:2007 | Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
| ISO 13845:2015 | Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes Test method for leaktightness under internal pressure and with angular deflection |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.