ISO 14526-2:1999
Current
The latest, up-to-date edition.
Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
English, French
11-18-1999
Important note : All end users must be registered with an Account prior to user licenses being assigned.
This part of ISO 14526 specifies the methods of preparation of test specimens and the test methods to be used in
determining the properties of phenolic powder moulding compounds (PF-PMCs). Requirements for handling test
material and for conditioning both the test material before moulding and the specimens before testing are given
here.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the
materials from which these specimens are made are given. Properties and test methods which are suitable and
necessary to characterize PMCs are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use
for, or of particular significance to, PMCs are also included in this part of ISO 14526, as are the designatory
properties found in ISO 14526-1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and
conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not
necessarily be identical to those obtained using specimens of different dimensions or prepared using different
procedures.
| DevelopmentNote |
Supersedes ISO 800 (12/2003)
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN ISO 14526-2 : 2000 | Identical |
| NBN EN ISO 14526-2 : 2000 | Identical |
| NEN EN ISO 14526-2 : 1999 | Identical |
| NS EN ISO 14526-2 : 1ED 2000 | Identical |
| I.S. EN ISO 14526-2:2000 | Identical |
| PN EN ISO 14526-2 : 2003 | Identical |
| SN EN ISO 14526-2 : 2000 | Identical |
| UNI EN ISO 14526-2 : 2002 | Identical |
| BS EN ISO 14526-2:2000 | Identical |
| EN ISO 14526-2:1999 | Identical |
| DIN EN ISO 14526-2:2000-08 | Identical |
| UNE-EN ISO 14526-2:2000 | Identical |
| BS EN ISO 14526-1:2000 | Plastics. Phenolic powder moulding compounds (PF-PMCs) Designation system and basis for specifications |
| BIS IS 13360-2-2 : 2013 | PLASTICS - METHODS OF TESTING - PART 2: SAMPLING AND PREPARATION OF TEST SPECIMENS - SECTION 2: COMPRESSION MOULDED TEST SPECIMENS OF THERMOPLASTIC MATERIALS |
| DIN EN ISO 295:2004-05 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| BS EN ISO 14526-3:2000 | Plastics. Phenolic powder moulding compounds (PF-PMCs) Requirements for selected moulding compounds |
| BS EN ISO 295:2004 | Plastics. Compression moulding of test specimens of thermosetting materials |
| ISO 14526-3:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| EN ISO 14526-3:1999 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 3: Requirements for selected moulding compounds (ISO 14526-3:1999) |
| EN ISO 14526-1:1999 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14526-1:1999) |
| EN ISO 295:2004 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 3671:1976 | Plastics — Aminoplastic moulding materials — Determination of volatile matter |
| ISO 14526-1:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 1: Designation system and basis for specifications |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 120:1977 | Plastics Phenol-formaldehyde mouldings Determination of free ammonia and ammonium compounds Colorimetric comparison method |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 2039-1:2001 | Plastics Determination of hardness Part 1: Ball indentation method |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 60:1977 | Plastics — Determination of apparent density of material that can be poured from a specified funnel |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| IEC 60167:1964 | Methods of test for the determination of the insulation resistance of solid insulating materials |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60707:1999 | Flammability of solid non-metallic materials when exposed to flame sources - List of test methods |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 14526-3:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 7808:1992 | Plastics — Thermosetting moulding materials — Determination of transfer flow |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 4614:1977 | Plastics Melamine-formaldehyde mouldings Determination of extractable formaldehyde |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.