ISO 1268-10:2005
Current
Current
The latest, up-to-date edition.
Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English, French
Published date
02-04-2005
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 1268-10:2005 specifies the general principles to be followed while injection moulding test specimens of bulk moulding compound (BMC) and gives details of mould designs for preparing one type of specimen for use in establishing reproducible moulding conditions. Where appropriate, this part of ISO 1268 may be applied to sheet moulding compound (SMC) formulated for injection moulding. Its purpose is to promote uniformity in describing the main parameters of the moulding process and also to establish uniform practice in reporting moulding conditions. The particular conditions required for the reproducible preparation of test specimens which will give comparable results will vary for each material used. These conditions are given in the International Standard for the relevant material or are to be agreed upon between interested parties.
| DevelopmentNote |
Supersedes ISO/DIS 1268-10 Together with ISO 1268-1, ISO 1268-2, ISO 1268-3, ISO 1268-5, ISO 1268-6, ISO 1268-7, ISO 1268-8, ISO 1268-9 and ISO 1268-11 supersedes ISO 1268. (02/2005)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NEN ISO 1268-10 : 2005 | Identical |
| NF ISO 1268-10 : 2006 | Identical |
| UNE-ISO 1268-10:2012 | Identical |
| SAC GB/T 27797-10 : 2011 | Identical |
| BS ISO 1268-10:2005 | Identical |
| BS EN ISO 20643:2005 | Identical |
| BS ISO 14649-1:2003 | Identical |
| UNI EN ISO 25762 : 2012 | PLASTICS - GUIDANCE ON THE ASSESSMENT OF THE FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED POLYMER COMPOSITES |
| DIN EN 14598-3:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| DIN EN 14598-2:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements |
| DIN EN ISO 25762:2012-04 | Plastics - Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites (ISO 25762:2009) |
| UNE-ISO 1268-11:2012 | Fibre-reinforced plastics. Methods of producing test plates. Part 11: Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| ISO 1268-11:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates |
| BS EN 14598-2:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements |
| BS ISO 25762 : 2009 | PLASTICS - GUIDANCE ON THE ASSESSMENT OF THE FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED POLYMER COMPOSITES |
| BS ISO 1268-11:2005 | Fibre-reinforced plastics. Methods of producing test plates Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| BS EN ISO 25762:2012 | Plastics. Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites |
| I.S. EN ISO 25762:2012 | PLASTICS - GUIDANCE ON THE ASSESSMENT OF THE FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED POLYMER COMPOSITES (ISO 25762:2009) |
| 02/124520 DC : DRAFT DEC 2002 | EN 14598-3 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS |
| ONORM EN ISO 180 : 2013 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000 + AMD. 1:2006 + AMD. 2:2013) |
| BS EN 14598-3:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements |
| ISO 25762:2009 | Plastics Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites |
| EN ISO 25762:2012 | Plastics - Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites (ISO 25762:2009) |
| EN 14598-3:2005 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| 02/124519 DC : DRAFT DEC 2002 | EN 14598-2 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS |
| ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
| ISO 1268-1:2001 | Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions |
| ISO 8693:2011 | Tools for moulding Flat ejector pins |
| ISO 10907-1:2008 | Tools for moulding — Locating rings — Part 1: Locating rings for mounting without thermal insulating sheets in small or medium moulds (types A and B) |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| ISO 8017:2007 | Tools for moulding Guide pillars, straight and shouldered, and locating guide pillars, shouldered |
| ISO 6751:2011 | Tools for moulding — Ejector pins with cylindrical head |
| ISO 11403-3:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ISO 8406:2008 | Tools for moulding — Mould bases — Round locating elements and spacers |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 6753-2:1998 | Tools for pressing and moulding Machined plates Part 2: Machined plates for moulds |
| ISO 9449:2007 | Tools for moulding Centring sleeves |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 8018:2007 | Tools for moulding Guide bushes, headed, and locating guide bushes, headed |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| ISO 8404:2013 | Tools for moulding Angle pins |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 294-2:1996 | Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| ISO 8405:2013 | Tools for moulding Ejector sleeves with cylindrical head Basic series for general purposes |
| ISO 10072:2004 | Tools for moulding — Sprue bushes — Dimensions |
| ISO 8694:2011 | Tools for moulding — Shouldered ejector pins |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 10073:2008 | Tools for moulding — Support pillars |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| ISO 12165:2000 | Tools for moulding Components of compression and injection moulds and diecasting dies Terms and symbols |
| ISO 1268-11:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.