ISO 12176-1:2017
Current
Current
The latest, up-to-date edition.
Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English, French
Published date
07-20-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 12176-1:2017 specifies the general characteristics of, and performance requirements for, equipment for butt fusion jointing of polyethylene (PE) piping systems using electrically powered heater plates.
ISO 12176-1:2017 is applicable to mechanical and pressure-activated equipment for butt fusion jointing of PE pipes and fittings either intended to be used for the supply of gaseous fuels, conforming to ISO 4437‑2[1] and ISO 4437‑3[2], or intended for the conveyance of water for human consumption (including raw water prior to treatment) and for the conveyance of water for general purposes, conforming to ISO 4427‑2[3] and ISO 4427‑3[4].
Butt fusion machines with an automatic controller are subject to additional requirements as given in Annex A.
NOTE This document is also applicable to butt fusion machines for larger nominal pipe diameters and nominal wall thicknesses than given in this document.
| DevelopmentNote |
Supersedes ISO/DIS 12176-1. (07/2017)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNI ISO 12176-1:2018 | Identical |
| NEN ISO 12176-1 : 2017 | Identical |
| BS ISO 12176-1:2017 | Identical |
| UNI ISO 12176-1 : 2015 | Identical |
| ISO 13951:2015 | Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| BS ISO 13951:2015 | Plastics piping systems. Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| UNI/TR 11481 : 2013 | Usi del polietilene nelle linee dirette e nella distribuzione del gas combustibile - Tecnologie riconosciute e applicabili - Linee guida di orientamento per gli operatori |
| ISO 22621-6:2010 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 6: Code of practice for design, handling and installation |
| 02/121564 DC : DRAFT APR 2002 | BS EN 14409-3 - PLASTICS PIPING SYSTEMS FOR THE RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE FIT-PIPES |
| NF EN ISO 11298-3 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| UNI EN ISO 11296-3 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| 02/123322 DC : DRAFT AUG 2002 | BS ISO 19480 - THERMOPLASTICS PIPES AND FITTINGS FOR THE SUPPLY OF GASEOUS FUELS - TRAINING AND ASSESSMENT OF FUSION-MACHINE OPERATORS |
| 09/30181333 DC : 0 | BS ISO 22621-6 ISO/CD 22621-6 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURES UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 6: CODE OF PRACTICE FOR DESIGN, HANDLING AND INSTALLATION |
| 17/30341312 DC : 0 | BS EN ISO 21225-1 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 1: REPLACEMENT ON THE LINE BY PIPE BURSTING AND PIPE EXTRACTION |
| 05/30128654 DC : DRAFT FEB 2005 | EN 1775 - GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| 10/30212150 DC : 0 | BS EN 12201-3 - PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - PART 3: FITTINGS |
| ISO 11296-2:2018 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 2: Lining with continuous pipes |
| ISO 11299-3:2011 | Plastics piping systems for renovation of underground gas supply networks Part 3: Lining with close-fit pipes |
| I.S. 820:2010 | NON-DOMESTIC GAS INSTALLATIONS |
| I.S. EN ISO 11297-2:2018 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 2: LINING WITH CONTINUOUS PIPES (ISO 11297-2:2018) |
| NF EN ISO 11296-3 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| ISO 21307:2017 | Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems |
| EN ISO 11296-3:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011) |
| DIN EN 12007-2:2012-10 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL REQUIREMENTS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| ONORM EN 12201-3 : 2013 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS |
| ISO 8085-2:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels Metric series Specifications Part 2: Spigot fittings for butt fusion, for socket fusion using heated tools and for use with electrofusion fittings |
| UNI EN ISO 11298-3 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| I.S. EN ISO 1167-4:2007 | THERMOPLASTICS PIPES, FITTINGS AND ASSEMBLIES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF THE RESISTANCE TO INTERNAL PRESSURE - PART 4: PREPARATION OF ASSEMBLIES |
| I.S. EN 14408-3:2004 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| I.S. EN 14409-3:2004 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE FIT-PIPES |
| 17/30341315 DC : 0 | BS EN ISO 21225-2 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 2: REPLACEMENT OFF THE LINE BY HORIZONTAL DIRECTIONAL DRILLING AND IMPACT MOLING |
| BS ISO 12176-3:2011 | Plastics pipes and fittings. Equipment for fusion jointing polyethylene systems Operator\'s badge |
| I.S. EN ISO 11299-3:2013 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11299-3:2011) |
| BS ISO 4427-3:2007 | Plastics piping systems. Polyethylene (PE) pipes and fittings for water supply Fittings |
| ISO 21225-1:2018 | Plastics piping systems for the trenchless replacement of underground pipeline networks — Part 1: Replacement on the line by pipe bursting and pipe extraction |
| CSA Z662 PACKAGE : 2011 | CONSISTS OF Z662-11, OIL AND GAS PIPELINE SYSTEMS AND Z662.1-11, COMMENTARY ON CSA Z662-11, OIL AND GAS PIPELINE SYSTEMS |
| I.S. EN ISO 11297-3:2013 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013) |
| I.S. EN ISO 11298-3:2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| DIN EN ISO 11297-3:2013-11 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11297-3:2013) |
| UNI ISO 12176-4 : 2014 | PLASTICS PIPES AND FITTINGS - EQUIPMENT FOR FUSION JOINTING POLYETHYLENE SYSTEMS - PART 4: TRACEABILITY CODING |
| UNE-EN ISO 11299-3:2014 | Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2011) |
| BS EN ISO 11296-3:2011 | Plastics piping systems for renovation of under ground non-pressure drainage and sewerage networks Lining with close-fit pipes |
| UNE-EN ISO 11297-3:2014 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes (ISO 11297-3:2013) |
| EN ISO 11297-2:2018 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 2: Lining with continuous pipes (ISO 11297-2:2018) |
| DIN EN 1775:2007-10 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| I.S. EN 12201-3:2011 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS |
| DIN EN 14409-3:2004-12 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| I.S. EN 12007-2:2012 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL REQUIREMENTS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| I.S. EN 1775:2007 | GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| BS ISO 11414:2009 | Plastics pipes and fittings. Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| ISO 11298-2:2018 | Plastics piping systems for renovation of underground water supply networks — Part 2: Lining with continuous pipes |
| ISO 11297-2:2018 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 2: Lining with continuous pipes |
| 16/30315817 DC : 0 | BS EN ISO 11296-2 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES |
| 12/30258383 DC : 0 | BS EN ISO 11297-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES |
| UNI EN ISO 1167-4 : 2008 | THERMOPLASTICS PIPES, FITTINGS AND ASSEMBLIES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF THE RESISTANCE TO INTERNAL PRESSURE - PART 4: PREPARATION OF ASSEMBLIES |
| EN ISO 11297-3:2013 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes (ISO 11297-3:2013) |
| CAN/CSA-Z662-15 | Oil and gas pipeline systems |
| ISO 11296-3:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 3: Lining with close-fit pipes |
| EN ISO 11298-2:2018 | Plastics piping systems for renovation of underground water supply networks - Part 2: Lining with continuous pipes (ISO 11298-2:2018) |
| ISO/TS 10839:2000 | Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
| BS EN 14409-3:2004 | Plastics piping systems for renovation of underground water supply networks Lining with close fit pipes |
| BS EN 12201-3 : 2011 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS |
| BS EN 12007-2:2012 | Gas infrastructure. Pipelines for maximum operating pressure up to and including 16 bar Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| UNE-EN 12007-2:2013 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| UNI EN 12007-2 : 2012 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL REQUIREMENTS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| UNI EN 12201-3 : 2013 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS |
| UNI EN 1775 : 2007 | GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| DIN ISO 16486-6:2015-07 | Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 6: Code of practice for design, handling and installation (ISO 16486-6:2012) |
| UNI ISO 12176-3 : 2014 | PLASTICS PIPES AND FITTINGS - EQUIPMENT FOR FUSION JOINTING POLYETHYLENE SYSTEMS - PART 3: OPERATOR'S BADGE |
| 10/30208795 DC : 0 | BS EN 12007-2 - GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL RECOMMENDATIONS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| PREN 12007-2 : DRAFT 2010 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 2: SPECIFIC FUNCTIONAL RECOMMENDATIONS FOR POLYETHYLENE (MOP UP TO AND INCLUDING 10 BAR) |
| 12/30264202 DC : 0 | BS EN ISO 11299-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| ISO 11414:2009 | Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| BS ISO 22621-6:2010 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar). Polyamide (PA) Code of practice for design, handling and installation |
| UNE 53940:2010 | Plastics. Polyethylene (PE) fabricated fittings for piping systems for water supply under pressure |
| BS ISO 8085-2:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels. Metric series. Specifications Spigot fittings for butt fusion, for socket fusion using heated tools and for use with eletrofusion fittings |
| BS EN ISO 11299-3:2013 | Plastics piping systems for renovation of underground gas supply networks Lining with close-fit pipes |
| I.S. EN ISO 11296-2:2018 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES (ISO 11296-2:2018) |
| UNI EN ISO 11297-3 : 2013 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES |
| BS EN ISO 11297-3:2013 | Plastics piping systems for renovation of underground drainage and sewerage networks under pressure Lining with close-fit pipes |
| ONORM EN ISO 11299-3 : 2013 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11299-3:2011) |
| ISO 11298-3:2010 | Plastics piping systems for renovation of underground water supply networks Part 3: Lining with close-fit pipes |
| ISO 16486-6:2012 | Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing — Part 6: Code of practice for design, handling and installation |
| ISO 12176-3:2011 | Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 3: Operator's badge |
| EN ISO 11299-3:2013 | Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2011) |
| EN ISO 11296-2:2018 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018) |
| DIN EN 12201-3:2013-01 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 3: FITTINGS |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| BS EN 14408-3:2004 | Plastics piping systems for renovation of underground gas supply networks Lining with close-fit pipes |
| EN 14409-3:2004 | Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close fit-pipes |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| EN ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
| EN 14408-3:2004 | Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes |
| 10/30206101 DC : 0 | BS ISO 11299-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LIMNING WITH CLOSE-FIT PIPES |
| BS ISO 21307:2011 | Plastics pipes and fittings. Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems |
| 17/30361344 DC : 0 | BS EN ISO 11298-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| 08/30174014 DC : DRAFT JUNE 2008 | BS ISO 11298-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT-PIPES |
| 16/30315811 DC : 0 | BS EN ISO 11297-2 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 2: LINING WITH CONTINUOUS PIPES |
| BS EN ISO 11298-3:2011 | Plastics piping systems for renovation of underground water supply networks Lining with close-fit pipes |
| 16/30315823 DC : 0 | BS EN ISO 11298-2 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES |
| I.S. EN ISO 11298-2:2018 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES (ISO 11298-2:2018) |
| ISO/TS 18226:2006 | Plastics pipes and fittings — Reinforced thermoplastics pipe systems for the supply of gaseous fuels for pressures up to 4 MPa (40 bar) |
| UNI EN ISO 11299-3 : 2013 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| ISO/TR 19480:2005 | Polyethylene pipes and fittings for the supply of gaseous fuels or water — Training and assessment of fusion operators |
| DIN EN ISO 11296-3:2011-07 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| UNE-EN ISO 11296-3:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011) |
| ISO 12176-4:2003 | Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 4: Traceability coding |
| UNE-EN ISO 11298-3:2011 | Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2010) |
| EN ISO 11298-3:2011 | Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2010) |
| ISO 4427-3:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings |
| I.S. EN ISO 11296-3:2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| DIN EN 14408-3:2004-12 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| DIN EN ISO 1167-4:2008-02 | THERMOPLASTICS PIPES, FITTINGS AND ASSEMBLIES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF THE RESISTANCE TO INTERNAL PRESSURE - PART 4: PREPARATION OF ASSEMBLIES |
| BS EN 1775:2007 | Gas supply. Gas pipework for buildings. Maximum operating pressure less than or equal to 5 bar. Functional recommendations |
| BS EN ISO 1167-4 : 2008 | THERMOPLASTICS PIPES, FITTINGS AND ASSEMBLIES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF THE RESISTANCE TO INTERNAL PRESSURE - PART 4: PREPARATION OF ASSEMBLIES |
| DIN EN ISO 11298-3:2011-07 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| DIN EN ISO 11299-3:2013-05 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES (ISO 11299-3:2011) |
| EN 12201-3:2011+A1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| UNE-EN 12201-3:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 4427-3:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings |
| ISO 12176-4:2003 | Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 4: Traceability coding |
| ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes |
| ISO 11414:2009 | Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| ISO 4437-3:2014 | Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings |
| ISO 4427-2:2007 | Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 2: Pipes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.