ISO 10619-1:2011
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Withdrawn date
09-27-2018
Superseded by
Language(s)
French, English
Published date
11-24-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.
ISO 10619-1:2011 specifies three methods for measuring the flexibility of rubber and plastics hoses and tubing (methods A1, B and C1), where the deformation of the hose or tubing is measured, and two methods for measuring the stiffness (methods A2 and C2) by measuring the force to bend the hose or tubing when rubber or plastics hoses or tubing are bent to a specific radius at ambient temperature.
Methods A1 and A2 are suitable for rubber and plastics hoses and tubing with inside diameter of up to and including 80 mm.
Method A1 allows the measurement of the flexibility of the hose or tubing by measuring the reduction in outside diameter when the hose is compressed between two plates.
Method A2 provides a means of measuring the force required to reach a specific bend radius, when the hose or tubing is compressed, as between two plates. The test can be carried out at a specified internal pressure.
Method B is suitable for rubber and plastics hoses and tubing with inside diameter of up to and including 100 mm, and provides a means of assessing the behaviour of the hose and tubing when bent around a mandrel. The final mandrel diameter used can be taken as the minimum bend radius of the hose or tubing. As this value is determined by the reduction of the outside diameter which can be used as a measure of the flexibility of the hose or tubing. The hose or tubing being tested can be unpressurized, pressurized or under vacuum and, if required, with the curvature or against the curvature of the hose or tubing, if such curvature is present.
Methods C1 and C2 are suitable for rubber and plastics hoses and tubing with inside diameter of 100 mm and greater.
Method C1 provides a means of determining the flexibility of the hose and tubing at the minimum bend radius.
Method C2 provides a method of measuring the stiffness of the hose and tubing at the minimum bend radius.
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| I.S. EN ISO 10619-1:2018 | Identical |
| BS EN ISO 10619-1:2011 | Identical |
| NEN EN ISO 10619-1 : 2018 | Identical |
| ONORM EN ISO 10619-1 : 2018 | Identical |
| UNI EN ISO 10619-1 : 2012 | Identical |
| EN ISO 10619-1:2018 | Identical |
| BIS IS 12656 : 2014 | Identical |
| GOST ISO 10619-1 : 2016 | Identical |
| PN EN ISO 10619-1 : 2012 | Identical |
| NF EN ISO 10619-1 : 2018 | Identical |
| NS EN ISO 10619-1 : 2018 | Identical |
| NBN EN ISO 10619-1 : 2012 | Identical |
| SN EN ISO 10619-1 : 2012 | Identical |
| UNE-EN ISO 10619-1:2012 | Identical |
| DIN EN ISO 10619-1:2012-03 | Identical |
| 12/30264538 DC : 0 | BS ISO 27127 - THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF LIQUID PETROLEUM GAS AND LIQUEFIED NATURAL GAS - SPECIFICATION |
| I.S. EN 13765:2010 | THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF HYDROCARBONS, SOLVENTS AND CHEMICALS - SPECIFICATION |
| 14/30290411 DC : 0 | BS EN 13765:2010/A1 - THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF HYDROCARBONS, SOLVENTS AND CHEMICALS - SPECIFICATION |
| UNE-EN 13765:2010 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification |
| 15/30317657 DC : 0 | BS EN ISO 2398 - RUBBER HOSE, TEXTILE-REINFORCED, FOR COMPRESSED AIR - SPECIFICATION |
| BS EN ISO 18752:2016 | Rubber hoses and hose assemblies. Wire- or textile-reinforced single-pressure types for hydraulic applications. Specification |
| ISO 11237:2017 | Rubber hoses and hose assemblies — Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids — Specification |
| BS ISO 4081:2016 | Rubber hoses and tubing for cooling systems for internal-combustion engines. Specification |
| ISO 3949:2009 | Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification |
| BS ISO 18752 : 2014 | RUBBER HOSES AND HOSE ASSEMBLIES - WIRE- OR TEXTILE-REINFORCED SINGLE-PRESSURE TYPES FOR HYDRAULIC APPLICATIONS - SPECIFICATION |
| ISO 4081:2016 | Rubber hoses and tubing for cooling systems for internal-combustion engines Specification |
| ISO 3862:2017 | Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 1823:2015 | Rubber hose and hose assemblies for oil suction and discharge service Specification |
| BS ISO 23297:2017 | Thermoplastic hoses and hose assemblies. Wire or synthetic yarn reinforced single-pressure types for hydraulic applications. Specification |
| ISO 5772:2015 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems Specification |
| EN 13765:2010+A1:2015 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification |
| DIN EN 13483:2013-09 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| BS EN 13482:2013 | Rubber hoses and hose assemblies for asphalt and bitumen. Specification |
| BS EN ISO 6134:2017 | Rubber hoses and hose assemblies for saturated steam. Specification |
| UNE-EN ISO 6224:2012 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011) |
| BS EN ISO 5774:2016 | Plastics hoses. Textile-reinforced types for compressed-air applications. Specification |
| DIN EN ISO 6808:2000-11 | PLASTICS HOSES AND HOSE ASSEMBLIES FOR SUCTION AND LOW-PRESSURE DISCHARGE OF PETROLEUM LIQUIDS - SPECIFICATION (ISO 6808:2014) |
| UNE-EN 16643:2017 | Rubber and plastics hoses and hose assemblies - Non-bonded fluoroplastic lined (e.g. PTFE) hoses and hose assemblies for liquid and gaseous chemicals - Specification |
| BS ISO 5772:2015 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems. Specification |
| PD ISO/TS 11619:2014 | Polyurethane tubing for use primarily in pneumatic installations. Dimensions and specification |
| 16/30335320 DC : 0 | BS ISO 4079 - RUBBER HOSES AND HOSE ASSEMBLIES - TEXTILE-REINFORCED HYDRAULIC TYPES FOR OIL-BASED OR WATER-BASED FLUIDS - SPECIFICATION |
| 16/30335329 DC : 0 | BS ISO 3862 - RUBBER HOSES AND HOSE ASSEMBLIES - RUBBER-COVERED SPIRAL-WIRE-REINFORCED HYDRAULIC TYPES FOR OIL-BASED OR WATER-BASED FLUIDS - SPECIFICATION |
| 15/30295265 DC : 0 | BS EN 13204 - DOUBLE ACTING HYDRAULIC RESCUE TOOLS FOR FIRE AND RESCUE SERVICE USE - SAFETY AND PERFORMANCE REQUIREMENTS |
| 17/30366640 DC : 0 | BS ISO 14743 - PNEUMATIC FLUID POWER - PUSH-IN CONNECTORS FOR THERMOPLASTIC TUBES |
| 15/30293925 DC : 0 | BS EN ISO 6134 - RUBBER HOSES AND HOSE ASSEMBLIES FOR SATURATED STEAM - SPECIFICATION |
| BS ISO 4079:2017 | Rubber hoses and hose assemblies. Textile-reinforced hydraulic types for oil-based or water-based fluids. Specification |
| ISO 4079:2017 | Rubber hoses and hose assemblies Textile-reinforced hydraulic types for oil-based or water-based fluids Specification |
| 16/30330752 DC : 0 | BS EN 13766 - THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF LIQUID PETROLEUM GAS AND LIQUEFIED NATURAL GAS - SPECIFICATION |
| ISO 6804:2016 | Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification |
| 18/30363978 DC : 0 | BS EN 1762 - RUBBER HOSES AND HOSE ASSEMBLIES FOR LIQUEFIED PETROLEUM GAS, LPG (LIQUID OR GASEOUS PHASE), AND NATURAL GAS UP TO 25 BAR (2,5 MPA) - SPECIFICATION |
| BS EN 1762:2017 | Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa). Specification |
| DIN EN 13482:2013-12 | Rubber hoses and hose assemblies for asphalt and bitumen - Specification |
| UNE-EN ISO 3994:2014 | Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:2014) |
| ISO 6134:2017 | Rubber hoses and hose assemblies for saturated steam — Specification |
| UNE-EN ISO 6134:2017 | Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2017) |
| I.S. EN 13483:2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| I.S. EN ISO 1401:2016 | RUBBER HOSES FOR AGRICULTURAL SPRAYING (ISO 1401:2016) |
| I.S. EN ISO 5774:2016 | PLASTICS HOSES - TEXTILE-REINFORCED TYPES FOR COMPRESSED-AIR APPLICATIONS - SPECIFICATION (ISO 5774:2016) |
| I.S. EN ISO 2398:2016 | RUBBER HOSES, TEXTILE-REINFORCED, FOR COMPRESSED AIR - SPECIFICATION (ISO 2398:2016) |
| I.S. EN ISO 3994:2014 | PLASTICS HOSES - HELICAL-THERMOPLASTIC-REINFORCED THERMOPLASTICS HOSES FOR SUCTION AND DISCHARGE OF AQUEOUS MATERIALS - SPECIFICATION (ISO 3994:2014) |
| I.S. EN ISO 6134:2017 | RUBBER HOSES AND HOSE ASSEMBLIES FOR SATURATED STEAM - SPECIFICATION (ISO 6134:2017) |
| I.S. EN 1360:2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| I.S. EN 13482:2013 | RUBBER HOSES AND HOSE ASSEMBLIES FOR ASPHALT AND BITUMEN - SPECIFICATION |
| I.S. EN ISO 6808:2014 | PLASTICS HOSES AND HOSE ASSEMBLIES FOR SUCTION AND LOW-PRESSURE DISCHARGE OF PETROLEUM LIQUIDS - SPECIFICATION (ISO 6808:2014) |
| I.S. EN 13204:2016 | DOUBLE ACTING HYDRAULIC RESCUE TOOLS FOR FIRE AND RESCUE SERVICE USE - SAFETY AND PERFORMANCE REQUIREMENTS |
| ONORM EN 13483 : 2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| UNE-EN ISO 28017:2012 | Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO 28017:2011) |
| PREN 13766 : DRAFT 2016 | THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF LIQUID PETROLEUM GAS AND LIQUEFIED NATURAL GAS - SPECIFICATION |
| BS EN ISO 8029:2014 | Plastics hose. General-purpose collapsible water hose, textile-reinforced. Specification |
| DIN EN 16820:2015-03 (Draft) | RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY - BONDED ELASTOMERIC HOSES WITH OR WITHOUT A LINING |
| ISO 19385:2017 | Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for water jetting or water blasting applications Specification |
| DIN EN 1360:2013-09 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| 15/30317651 DC : 0 | BS ISO 11424 - RUBBER HOSES AND TUBING FOR AIR AND VACUUM SYSTEMS FOR INTERNAL-COMBUSTION ENGINES - SPECIFICATION |
| 15/30301522 DC : 0 | BS ISO 13775-2 - THERMOPLASTIC TUBING AND HOSES FOR AUTOMOTIVE USE - PART 2: PETROLEUM-BASED-FUEL APPLICATIONS |
| 14/30293931 DC : 0 | BS ISO 19013-2 - RUBBER HOSES AND TUBING FOR FUEL CIRCUITS FOR INTERNAL COMBUSTION ENGINES - SPECIFICATION - PART 2: GASOLINE FUELS |
| ISO 27126:2014 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals Specification |
| 16/30326500 DC : DRAFT JAN 2016 | BS ISO 19385 - RUBBER HOSES AND HOSE ASSEMBLIES FOR WATER JETTING OR WATER BLASTING APPLICATIONS |
| BS ISO 16301:2017 | Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for manually operated hydraulic jacks. Specification |
| 14/30293928 DC : 0 | BS ISO 13775-1 - THERMOPLASTIC TUBING AND HOSES FOR AUTOMOTIVE USE - PART 1: NON-FUEL APPLICATIONS |
| UNE-EN ISO 4641:2017 | Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO 4641:2016) |
| DIN EN ISO 8029:2014-12 | PLASTICS HOSE - GENERAL-PURPOSE COLLAPSIBLE WATER HOSE, TEXTILE-REINFORCED - SPECIFICATION (ISO 8029:2014) |
| BS ISO 11424:2017 | Rubber hoses and tubing for air and vacuum systems for internal-combustion engines. Specification |
| ISO 28017:2018 | Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications — Specification |
| I.S. EN ISO 28017:2018 | RUBBER HOSES AND HOSE ASSEMBLIES, WIRE OR TEXTILE REINFORCED, FOR DREDGING APPLICATIONS - SPECIFICATION (ISO 28017:2018) |
| I.S. EN 16643:2016 | RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES - NON-BONDED LUOROPLASTIC LINED (E.G. PTFE) HOSES AND HOSE ASSEMBLIES FOR IQUID AND GASEOUS CHEMICALS - SPECIFICATION |
| UNI EN ISO 8029 : 2014 | PLASTICS HOSE - GENERAL-PURPOSE COLLAPSIBLE WATER HOSE, TEXTILE-REINFORCED - SPECIFICATION |
| ISO/TS 11619:2014 | Polyurethane tubing for use primarily in pneumatic installations — Dimensions and specification |
| EN ISO 28017:2018 | Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO 28017:2018) |
| ISO 13775-1:2015 | Thermoplastic tubing and hoses for automotive use Part 1: Non-fuel applications |
| I.S. EN ISO 4641:2016 | RUBBER HOSES AND HOSE ASSEMBLIES FOR WATER SUCTION AND DISCHARGE - SPECIFICATION (ISO 4641:2016) |
| DIN EN ISO 6808:2014-10 | PLASTICS HOSES AND HOSE ASSEMBLIES FOR SUCTION AND LOW-PRESSURE DISCHARGE OF PETROLEUM LIQUIDS - SPECIFICATION (ISO 6808:2014) |
| DIN EN ISO 3994:2015-11 | PLASTICS HOSES - HELICAL-THERMOPLASTIC-REINFORCED THERMOPLASTICS HOSES FOR SUCTION AND DISCHARGE OF AQUEOUS MATERIALS - SPECIFICATION (ISO 3994:2014) |
| UNE-EN ISO 6808:2015 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:2014) |
| ISO 1401:2016 | Rubber hoses for agricultural spraying |
| UNE-EN 13204:2017 | Double acting hydraulic rescue tools for fire and rescue service use - Safety and performance requirements |
| UNE-EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification |
| EN ISO 6808:2014 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:2014) |
| EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification |
| UNI EN 13482 : 2013 | RUBBER HOSES AND HOSE ASSEMBLIES FOR ASPHALT AND BITUMEN - SPECIFICATION |
| EN 13204:2016 | Double acting hydraulic rescue tools for fire and rescue service use - Safety and performance requirements |
| UNI EN 1360 : 2013 | RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| UNI EN ISO 6808 : 2014 | PLASTICS HOSES AND HOSE ASSEMBLIES FOR SUCTION AND LOW-PRESSURE DISCHARGE OF PETROLEUM LIQUIDS - SPECIFICATION |
| UNI EN ISO 3994 : 2014 | PLASTICS HOSES - HELICAL-THERMOPLASTIC-REINFORCED THERMOPLASTICS HOSES FOR SUCTION AND DISCHARGE OF AQUEOUS MATERIALS - SPECIFICATION |
| BS EN 16821:2017 | Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry. Silicone rubber hoses |
| BS EN 16820:2017 | Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry. Bonded elastomeric hoses with or without a lining |
| BS ISO 27126:2014 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals. Specification |
| 16/30311803 DC : 0 | BS ISO 16301 - RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES, WIRE- OR TEXTILE-REINFORCED, FOR MANUALLY OPERATED HYDRAULIC JACKS - SPECIFICATION |
| 12/30264535 DC : 0 | BS ISO 27126 - THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF HYDROCARBONS, SOLVENTS AND CHEMICALS - SPECIFICATION |
| UNE-EN ISO 18752:2017 | Rubber hoses and hose assemblies - Wire- or textile-reinforced single-pressure types for hydraulic applications - Specification (ISO 18752:2014) |
| PREN 13204 : DRAFT 2015 | DOUBLE ACTING HYDRAULIC RESCUE TOOLS FOR FIRE AND RESCUE SERVICE USE - SAFETY AND PERFORMANCE REQUIREMENTS |
| 16/30335326 DC : 0 | BS ISO 1436 - RUBBER HOSES AND HOSE ASSEMBLIES - WIRE-BRAID-REINFORCED HYDRAULIC TYPES FOR OIL-BASED OR WATER-BASED FLUIDS - SPECIFICATION |
| BS ISO 1823:2015 | Rubber hose and hose assemblies for oil suction and discharge service. Specification |
| BS ISO 19013-2:2005 | Rubber hoses and tubing for fuel circuits for internal combustion engines. Specification Gasoline fuels |
| 16/30317675 DC : 0 | BS EN ISO 3949 - PLASTICS HOSES AND HOSE ASSEMBLIES - TEXTILE-REINFORCED TYPES FOR HYDRAULIC APPLICATIONS - SPECIFICATION |
| BS EN ISO 4641:2016 | Rubber hoses and hose assemblies for water suction and discharge. Specification |
| ISO 16301:2017 | Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for manually operated hydraulic jacks — Specification |
| BS ISO 13775-1:2015 | Thermoplastic tubing and hoses for automotive use Non-fuel applications |
| DIN EN 1762:2016-09 (Draft) | RUBBER HOSES AND HOSE ASSEMBLIES FOR LIQUEFIED PETROLEUM GAS, LPG (LIQUID OR GASEOUS PHASE), AND NATURAL GAS UP TO 25 BAR (2,5 MPA) - SPECIFICATION |
| ISO 13775-2:2016 | Thermoplastic tubing and hoses for automotive use Part 2: Petroleum-based-fuel applications |
| I.S. EN ISO 18752:2016 | RUBBER HOSES AND HOSE ASSEMBLIES - WIRE- OR TEXTILE-REINFORCED SINGLE-PRESSURE TYPES FOR HYDRAULIC APPLICATIONS - SPECIFICATION (ISO 18752:2014) |
| DIN EN ISO 28017:2015-12 | RUBBER HOSES AND HOSE ASSEMBLIES, WIRE OR TEXTILE REINFORCED, FOR DREDGING APPLICATIONS - SPECIFICATION (ISO 28017:2011 + AMD 1:2015) |
| ISO 13363:2016 | Rubber and plastics hoses for marine-engine wet-exhaust systems — Specification |
| DIN EN 13765:2015-05 | THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF HYDROCARBONS, SOLVENTS AND CHEMICALS - SPECIFICATION |
| PREN 1762 : DRAFT 2018 | RUBBER HOSES AND HOSE ASSEMBLIES FOR LIQUEFIED PETROLEUM GAS, LPG (LIQUID OR GASEOUS PHASE), AND NATURAL GAS UP TO 25 BAR (2,5 MPA) - SPECIFICATION |
| ISO 19013-2:2016 | Rubber hoses and tubing for fuel circuits for internal combustion engines Specification Part 2: Gasoline fuels |
| I.S. EN 1762:2017 | RUBBER HOSES AND HOSE ASSEMBLIES FOR LIQUEFIED PETROLEUM GAS, LPG (LIQUID OR GASEOUS PHASE), AND NATURAL GAS UP TO 25 BAR (2,5 MPA) - SPECIFICATION |
| ISO 27127:2014 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas Specification |
| ISO 11424:2017 | Rubber hoses and tubing for air and vacuum systems for internal-combustion engines — Specification |
| ISO 23297:2017 | Thermoplastic hoses and hose assemblies — Wire or synthetic yarn reinforced single-pressure types for hydraulic applications — Specification |
| BS EN 13765 : 2010 | THERMOPLASTIC MULTI-LAYER (NON-VULCANIZED) HOSES AND HOSE ASSEMBLIES FOR THE TRANSFER OF HYDROCARBONS, SOLVENTS AND CHEMICALS - SPECIFICATION |
| DIN EN ISO 6134:2015-10 (Draft) | RUBBER HOSES AND HOSE ASSEMBLIES FOR SATURATED STEAM - SPECIFICATION (ISO 6134:2017) |
| BS EN ISO 2398:2016 | Rubber hoses, textile-reinforced, for compressed air. Specification |
| ISO 4641:2016 | Rubber hoses and hose assemblies for water suction and discharge — Specification |
| ISO 2398:2016 | Rubber hoses, textile-reinforced, for compressed air — Specification |
| UNE-EN ISO 1401:2017 | Rubber hoses for agricultural spraying (ISO 1401:2016) |
| BS EN 13204 : 2004 | DOUBLE ACTING HYDRAULIC RESCUE TOOLS FOR FIRE AND RESCUE SERVICE USE - SAFETY AND PERFORMANCE REQUIREMENTS |
| ISO 3994:2014 | Plastics hoses — Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials — Specification |
| UNE-EN 13482:2014 | Rubber hoses and hose assemblies for asphalt and bitumen - Specification |
| ISO 6808:2014 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids — Specification |
| BS EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems. Specification |
| BS EN ISO 3994:2014 | Plastics hoses. Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials. Specification |
| UNE-EN ISO 5774:2016 | Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2016) |
| BS EN ISO 1401:2016 | Rubber hoses for agricultural spraying |
| UNE-EN ISO 2398:2017 | Rubber hoses, textile-reinforced, for compressed air - Specification (ISO 2398:2016) |
| EN ISO 18752:2016 | Rubber hoses and hose assemblies - Wire- or textile-reinforced single-pressure types for hydraulic applications - Specification (ISO 18752:2014) |
| EN ISO 8029:2014 | Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification (ISO 8029:2014) |
| EN ISO 2398:2016 | Rubber hoses, textile-reinforced, for compressed air - Specification (ISO 2398:2016) |
| EN 16820:2017 | Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry - Bonded elastomeric hoses with or without a lining |
| EN 16643:2016 | Rubber and plastics hoses and hose assemblies - Non-bonded fluoroplastic lined (e.g. PTFE) hoses and hose assemblies for liquid and gaseous chemicals - Specification |
| EN ISO 6134:2017 | Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2017) |
| EN ISO 3994:2014 | Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:2014) |
| EN 16821:2017 | Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry - Silicone rubber hoses |
| EN ISO 1401:2016 | Rubber hoses for agricultural spraying (ISO 1401:2016) |
| EN ISO 5774:2016 | Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2016) |
| EN ISO 4641:2016 | Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO 4641:2016) |
| 15/30315105 DC : 0 | BS EN 16820 - HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY WITH HOSES OF NON-METALLIC MATERIALS - ELASTOMERIC HOSES WITH OR WITHOUT LINER |
| DIN EN 16821:2015-03 (Draft) | RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY - SILICONE RUBBER HOSES |
| 15/30317639 DC : 0 | BS ISO 6804 - RUBBER AND PLASTICS INLET HOSES AND HOSE ASSEMBLIES FOR WASHING-MACHINES AND DISHWASHERS - SPECIFICATION |
| DIN EN ISO 4641:2016-07 (Draft) | RUBBER HOSES AND HOSE ASSEMBLIES FOR WATER SUCTION AND DISCHARGE - SPECIFICATION (ISO 4641:2016) |
| 13/30275849 DC : 0 | BS ISO 5772 - RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION |
| BS ISO 27127:2014 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas. Specification |
| BS ISO 19385:2017+A1:2019 | Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for water jetting or water blasting applications - Specification |
| 15/30315109 DC : 0 | BS EN 16821 - HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY WITH HOSES OF NON-METALLIC MATERIALS - SILICONE RUBBER HOSES |
| UNE-EN ISO 8029:2014 | Plastics hose - General-purpose collapsible water hose, textile-reinforced - Specification (ISO 8029:2014) |
| 15/30317636 DC : 0 | BS EN ISO 1401 - RUBBER HOSES FOR AGRICULTURAL SPRAYING |
| 16/30302789 DC : DRAFT APR 2016 | BS ISO 19718 - RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES, WIRE- OR TEXTILE- REINFORCED, FOR HYDRAULIC POWER UNITS USED IN HYDRAULIC TOOL APPLICATIONS - SPECIFICATION |
| 15/30317663 DC : 0 | BS ISO 11759 - RUBBER HOSES AND HOSE ASSEMBLIES FOR DISPENSING LIQUEFIED PETROLEUM GASES (LPGS) - SPECIFICATION |
| BS ISO 13775-2:2016 | Thermoplastic tubing and hoses for automotive use Petroleum-based-fuel applications |
| EN 1762:2017 | Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification |
| BS ISO 2929:2014 | Rubber hoses and hose assemblies for bulk fuel delivery by truck. Specification |
| I.S. EN 16820:2017 | RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY - BONDED ELASTOMERIC HOSES WITH OR WITHOUT A LINING |
| BS ISO 1436:2017 | Rubber hoses and hose assemblies. Wire-braid-reinforced hydraulic types for oil-based or water-based fluids. Specification |
| UNE-EN 1762:2017 | Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification |
| I.S. EN 16821:2017 | RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY - SILICONE RUBBER HOSES |
| ISO 2929:2014 | Rubber hoses and hose assemblies for bulk fuel delivery by truck Specification |
| UNE-EN 16820:2018 | Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry - Bonded elastomeric hoses with or without a lining |
| UNE-EN 16821:2018 | Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry - Silicone rubber hoses |
| I.S. EN ISO 8029:2014 | PLASTICS HOSE - GENERAL-PURPOSE COLLAPSIBLE WATER HOSE, TEXTILE-REINFORCED - SPECIFICATION (ISO 8029:2014) |
| ISO 1436:2017 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification |
| UNE-EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| ISO 18752:2014 | Rubber hoses and hose assemblies Wire- or textile-reinforced single-pressure types for hydraulic applications Specification |
| BS EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems. Specification |
| ISO 5774:2016 | Plastics hoses — Textile-reinforced types for compressed-air applications — Specification |
| BS EN ISO 6808:2014 | Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids. Specification |
| ISO 8029:2014 | Plastics hose — General-purpose collapsible water hose, textile-reinforced — Specification |
| DIN EN ISO 6134:2006-02 | RUBBER HOSES AND HOSE ASSEMBLIES FOR SATURATED STEAM - SPECIFICATION (ISO 6134:2017) |
| DIN EN 1762:2004-07 | RUBBER HOSES AND HOSE ASSEMBLIES FOR LIQUEFIED PETROLEUM GAS, LPG (LIQUID OR GASEOUS PHASE), AND NATURAL GAS UP TO 25 BAR (2,5 MPA) - SPECIFICATION |
| EN 13482:2013 | Rubber hoses and hose assemblies for asphalt and bitumen - Specification |
| DIN EN ISO 6224:2012-02 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011) |
| EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| NF EN ISO 6134 : 2017 | RUBBER HOSES AND HOSE ASSEMBLIES FOR SATURATED STEAM - SPECIFICATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.