IPC J STD 004 : B
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
REQUIREMENTS FOR SOLDERING FLUXES
Available format(s)
Hardcopy
Superseded date
03-10-2022
Superseded by
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 SCOPE AND DESIGNATION
2 APPLICABLE DOCUMENTS
3 GENERAL REQUIREMENTS
4 QUALIFICATIONS AND QUALITY ASSURANCE PROVISIONS
Appendix A - Example Qualification Test Report
Appendix B - Notes
Describes general requirements for the classification and characterization of fluxes for high quality solder interconnections.
| DevelopmentNote |
Supersedes QQ S 571, MIL F 14256, IPC SF 818, QPL 14256, QPL QQ S 571 & DEFSTAN 34-4/2(1990). Included in IPC C 103 & IPC C 1000. (04/2006) A2004 Edition is available in Japanese Language, See J STD 004 JAPANESE. B2008 Edition Re-Issued in November 2011 & incorporates AMD 1 2011. Also available in Chinese & Russian languages, See J STD 004 CHINESE & J STD 004 RUSSIAN. (11/2012)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
Institute of Printed Circuits
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| IPC J STD 002 CHINESE : C | SOLDERABILITY TESTS FOR COMPONENT LEADS, TERMINATIONS, LUGS, TERMINALS AND WIRES |
| MIL-PRF-83504 Revision C:2005 | SWITCHES, DUAL IN-LINE PACKAGE (DIP), GENERAL SPECIFICATION FOR |
| MIL-DTL-83513 Revision G:2008 | Connectors, Electrical, Rectangular, Microminiature, Polarized Shell, General Specification for |
| MIL-C-11272 Revision E:2008 | CAPACITORS, FIXED, GLASS DIELECTRIC, GENERAL SPECIFICATION FOR |
| IPC AJ 820 : A | ASSEMBLY AND JOINING HANDBOOK |
| MIL-DTL-83731-16 Revision D:2007 | Switches, Toggle, Miniature, Right Angle (Horizontal), PCB Mount, Double Pole, Lever Seal, Flux Seal |
| MIL-PRF-914 Revision C:2008 | RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, NONESTABLISHED RELIABILITY, AND ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR |
| MIL C 5 : G | CAPACITOR, FIXED, MICA DIELECTRIC, GENERAL SPECIFICATION FOR |
| MIL C 39019 : C | CIRCUIT BREAKERS, MAGNETIC, LOW-POWER, SEALED, TRIP-FREE, GENERAL SPECIFICATION FOR |
| MIL-DTL-3607 Revision C:2009 | Connectors, Coaxial, Radiofrequency, Series for Pulse, General Specification for |
| IPC J STD 001 SWEDISH : E | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| IPC A 610 DANISH : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-DTL-28778 Revision A:2005 | TRANSFORMER, POWER, STEPUP, 3 PHASE |
| MIL-DTL-12109-21 Revision B:2011 | SOLENOID, ELECTRICAL; CLASS 2 (MACHINE GUN) 7.62 MM, 24 VOLT DC, 8 AMP MAX |
| MIL-DTL-22641 Revision G:2016 | ADAPTERS, COAXIAL TO WAVEGUIDE, GENERAL SPECIFICATION FOR |
| MIL P 50884 : E | PRINTED WIRING BOARD, FLEXIBLE OR RIGID-FLEX, GENERAL SPECIFICATION FOR |
| IPC J STD 001 RUSSIAN : E | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| MIL-DTL-7879 Revision E:2013 | Antenna AT-141A/ARC |
| IPC A 610 SPANISH : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC LDFR0805-CD : 2005 | IPC/JEDEC 9TH INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES AUGUST 2005 |
| IPC WHMA A 620 HUNGARIAN : B | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| IPC J STD 005 RUSSIAN : A | REQUIREMENTS FOR SOLDERING FLUXES |
| IPC J STD 001 TURKISH : E2010 | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| IPC J STD 001 POLISH : E | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| MIL-DTL-13253 Revision E:2007 | HANDSETS, GENERAL SPECIFICATION FOR |
| IPC A 610 ROMANIAN : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC LDFR1006-CD : 2006 | IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES "ROHS COMPLIANCE AND BEYOND" |
| MIL-DTL-14072 Revision F:2013 | FINISHES FOR GROUND BASED ELECTRONIC EQUIPMENT |
| MIL PRF 83513 : D | CONNECTORS, ELECTRICAL, RECTANGULAR, MICROMINIATURE, POLARIZED SHELL, GENERAL SPECIFICATION FOR |
| IPC WHMA A 620 TURKISH : B2012 AMD 1 2013 | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| IPC WHMA A 620 HEBREW : B2012 AMD 1 2013 | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| MIL-DTL-15743 Revision F:2017 | SWITCHES, ROTARY, ENCLOSED |
| IPC A 610 CZECH : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC TP 1090 : 1996 | THE LAYMAN'S GUIDE TO QUALIFYING NEW FLUXES FOR MIL-STD-2000A OR MT-0002 |
| IPC LDFR0806-CD : 2006 | IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES "ROHS COMPLIANCE AND BEYOND" |
| IPC LDFR0605-CD : 2005 | IPC/SOLDERTEC 3RD INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONICS "TOWARDS IMPLEMENTATION OF THE ROHS DIRECTIVE" |
| IPC LDFR1005-CD : 2005 | IPC/JEDEC 11TH INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES |
| IPC A 610 HINDI : E2010 | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-DTL-45068 Revision E:2006 | LIGHT, DOME, VEHICULAR, 24 VOLT DC |
| IPC 9592 : B | REQUIREMENTS FOR POWER CONVERSION DEVICES FOR THE COMPUTER AND TELECOMMUNICATIONS INDUSTRIES |
| IPC 5702 : 0 | GUIDELINES FOR OEMS IN DETERMINING ACCEPTABLE LEVELS OF CLEANLINESS OF UNPOPULATED PRINTED BOARDS |
| IPC LDFR1106-CD : 2006 | IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES "ROHS COMPLIANCE AND BEYOND" |
| IPC A 610 ESTONIAN : E2010 | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC A 610 POLISH : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC WHMA A 620 SPANISH : B | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| IPC WHMA A 620 CHINESE : B | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| MIL-PRF-39017 Revision G:2006 | RESISTOR, FIXED, FILM (INSULATED), NONESTABLISHED RELIABILITY, AND ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR |
| IPC A 610 DUTCH : F2014 | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC WHMA A 620 VIETNAMESE : B2012 | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| MIL-DTL-32139 Revision B:2017 | Connectors, Electrical, Rectangular, Nanominiature, Polarized Shell, General Specification for |
| MIL-PRF-39003 Revision N:2016 | Capacitor, Fixed, Electrolytic (Solid Electrolyte), Tantalum, Established Reliability, General Specification for |
| MIL B 18 : F | BATTERIES, NON-RECHARGEABLE, DRY |
| IPC A 610 KOREAN : F2014 | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-DTL-28754-62 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER, CROSSOVER, CONTACT TAILS ON .050 CENTERS |
| MIL-STD-2003-5 Revision A:2009 | ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS) |
| MIL-DTL-28748 Revision D:2001 | CONNECTOR, PLUG AND RECEPTACLE, RECTANGULAR, RACK AND PANEL SOLDER TYPE AND CRIMP TYPE CONTACTS - GENERAL SPECIFICATION FOR |
| MIL-PRF-55681 Revision G:2016 | CAPACITOR, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR |
| IPC CH 65 : B | GUIDELINES FOR CLEANING OF PRINTED BOARDS AND ASSEMBLIES |
| IPC LDFR0306-CD : 2006 | IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES |
| IPC CH 65 CHINESE : B | GUIDELINES FOR CLEANING OF PRINTED BOARDS AND ASSEMBLIES |
| IPC LDFR1205-CD : 2006 | IPC/JEDEC 12TH INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES - DECEMBER 2005 |
| MIL-DTL-917 Revision F:2014 | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS FOR |
| IPC A 610 ITALIAN : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-DTL-3786 Revision J:2013 | SWITCHES, ROTARY (CIRCUIT SELECTOR, LOW-CURRENT CAPACITY), GENERAL SPECIFICATION FOR |
| IPC A 610 FRENCH : F | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-STD-1353 Revision C:2014 | ELECTRICAL CONNECTORS, PLUG-IN SOCKETS AND ASSOCIATED HARDWARE, SELECTION AND USE OF |
| MIL-DTL-3965 Revision H:2004 | CAPACITOR, FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, GENERAL SPECIFICATION FOR |
| MIL STD 750-2 : A | MECHANICAL TEST METHODS FOR SEMICONDUCTOR DEVICES - PART 2: TEST METHODS 2001 THROUGH 2999 |
| MIL-PRF-49467 Revision C:2005 | Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose), General Specification For |
| MIL-DTL-28827 Revision C:2011 | SWITCHES, THERMOSTATIC, (VOLATILE LIQUID), HERMETICALLY SEALED, GENERAL SPECIFICATION FOR |
| IPC SM 840 : E | QUALIFICATION AND PERFORMANCE SPECIFICATION OF PERMANENT SOLDER MASK AND FLEXIBLE COVER MATERIALS |
| IPC TR 467 : 0 | SUPPORTING DATA AND NUMERICAL EXAMPLES FOR J-STD-001 (CONTROL OF FLUXES) |
| MIL PRF 24308 : D | CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL, RACK AND PANEL, GENERAL SPECIFICATION FOR |
| IPC HDBK 830 : A | GUIDELINES FOR DESIGN, SELECTION AND APPLICATION OF CONFORMAL COATINGS |
| IPC J STD 001 HUNGARIAN : E | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| IPC J STD 001 GERMAN : F | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| IPC 9203 : 0 | USERS GUIDE TO IPC-9202 AND THE IPC-B-52 STANDARD TEST VEHICLE |
| IPC A 610 SWEDISH : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC J STD 075 GERMAN : 0 | CLASSIFICATION OF NON-IC ELECTRONIC COMPONENTS FOR ASSEMBLY PROCESSES |
| IPC SM 840 CHINESE : E | QUALIFICATION AND PERFORMANCE SPECIFICATION OF PERMANENT SOLDER MASK AND FLEXIBLE COVER MATERIALS |
| IPC A 610 HUNGARIAN : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC WHMA A 620 POLISH : B | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| MIL-DTL-28754-6 Revision D:2014 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, 40 PIN, STRAIGHT THROUGH |
| MIL-PRF-3098 Revision L:2017 | CRYSTAL UNITS, QUARTZ, GENERAL SPECIFICATION FOR |
| MIL-DTL-1716 Revision J:1997 | POLE, TENT, TELESCOPIC, ADJUSTABLE 5 FEET TO 9 FEET, MAGNESIUM |
| IPC MI 660 : 1984 | INCOMING INSPECTION OF RAW MATERIALS MANUAL |
| MIL-DTL-3950 Revision K:2016 | Switches, Toggle, Environmentally Sealed, General Specification for |
| MIL-DTL-28754-97 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 150 CONTACT, RIGHT ANGLE, CONTACT TAILS ON 0.100 CENTERS |
| IPC A 610 CHINESE : F | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-DTL-9395 Revision K:2016 | Switches, Pressure (Absolute, Gage and Differential) General Specification for |
| IPC A 610 TURKISH : E2010 | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC LDFR0406-CD : 2006 | IPC/SOLDERTEC GLOBAL 4TH INTERNATIONAL ELECTRONICS CONFERENCE AND EXHIBITION "ROHS COMPLIANCE AND BEYOND" |
| IPC J STD 006 CHINESE : B-2 | REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDERS FOR ELECTRONIC SOLDERING APPLICATIONS |
| IPC J STD 001 ROMANIAN : F | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| IPC J STD 005 : A | REQUIREMENTS FOR SOLDERING PASTES |
| MIL-PRF-27 Revision G:2014 | TRANSFORMERS AND INDUCTORS (AUDIO, POWER, AND HIGH-POWER PULSE), GENERAL SPECIFICATION FOR |
| MIL STD 11991 : A | GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES |
| IPC A 610 JAPANESE : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| IPC J STD 005 CHINESE : A | REQUIREMENTS FOR SOLDERING PASTES |
| IPC J STD 075 CHINESE : - | CLASSIFICATION OF NON-IC ELECTRONIC COMPONENTS FOR ASSEMBLY PROCESSES |
| MIL-DTL-83731-22 Revision C:2010 | SWITCHES, TOGGLE, MINIATURE, LEVER-LOCK, FOUR POLE, LOGIC LOAD TO 5 AMPERES |
| MIL DTL 28754/60 : A | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS |
| MIL-DTL-16225 Revision C:2010 | LOUDSPEAKER, PERMANENT MAGNET, BLASTPROOF AND SUBMERSIBLE, NAVY TYPE 49546() |
| IPC J STD 001 DANISH : E | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| MIL-DTL-11996 Revision C:2015 | HANDSETS, GENERAL SPECIFICATION FOR |
| IPC A 610 RUSSIAN : D | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| OO-S-256 Revision K:2012 | Sewing Machine, Industrial, General Specification for |
| MIL-DTL-83731-15 Revision D:2007 | Switches, Toggle, Miniature, Right Angle (Vertical), PCB Mount, Single Pole, Lever Seal, Flux Seal |
| IPC A 610 VIETNAMESE : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-DTL-12606 Revision E:2000 | LOUDSPEAKER, PERMANENT MAGNET (UNENCASED, 3-INCH AND 4-INCH DIAMETER CONE, 2-WATT; FUNGUS-, AND IMMERSION-RESISTANT), TYPE LS-445/U, M12606-01, AND M12606-02 |
| MIL-DTL-12632 Revision E:2016 | LOUDSPEAKERS, PERMANENT MAGNET (ENCASED, 2-WATT, FUNGUS-, GUNBLAST-, AND IMMERSION-RESISTANT), GENERAL SPECIFICATION FOR |
| MIL-DTL-83731-21 Revision B:2010 | SWITCHES, TOGGLE, MINIATURE, LEVER SEAL, PANEL SEAL, FOUR POLE LOGIC LOAD TO 5 AMPERES |
| IPC WHMA A 620 ESTONIAN : B2012 AMD 1 2013 | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| IPC TP 1115 : 1998 | SELECTION AND IMPLEMENTATION STRATEGY FOR A LOW-RESIDUE, NO-CLEAN PROCESS |
| IPC WHMA A 620 KOREAN : B2012 AMD 1 2013 | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| MIL-DTL-18793 Revision B:2011 | ANTENNA AS-333/AP |
| MIL-STD-186 Revision F:2002 | PROTECTIVE FINISHING SYSTEMS FOR ROCKETS, GUIDED MISSILES, SUPPORT EQUIPMENT AND RELATED MATERIALS |
| MIL-STD-981 Revision C:2010 | DESIGN, MANUFACTURING AND QUALITY STANDARDS FOR CUSTOM ELECTROMAGNETIC DEVICES FOR SPACE APPLICATIONS |
| I.S. EN 3155-039:2007 | AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 039: CONTACTS, ELECTRICAL, COAXIAL, SIZE 16, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD |
| MS27144 Revision D:2016 | CONNECTOR, PLUG, ELECTRICAL, SOCKET CONTACT, NO. 14 AND 16 AWG, WATERPROOF |
| MIL-DTL-32234 Base Document:2007 | CONNECTORS, ELECTRICAL, ULTRA HIGH DENSITY, MODULAR, BLADE AND FORK, EIGHT ROW, GENERAL SPECIFICATION FOR |
| NASA KSC SPEC E 0031 : 2008 | CABLES, ELECTRICAL, SPECIFICATION FOR |
| IEC TR 62866:2014 | Electrochemical migration in printed wiring boards and assemblies - Mechanisms and testing |
| IPC WHMA A 620 DANISH : B | REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES |
| MIL-DTL-83725 Revision E:2017 | Relays, Vacuum, General Specification for |
| EN 61191-2:2017 | Printed board assemblies - Part 2: Sectional specification - Requirements for surface mount soldered assemblies |
| IEC 61191-2:2017 | Printed board assemblies - Part 2: Sectional specification - Requirements for surface mount soldered assemblies |
| MIL-DTL-28754-59 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS (CERAMIC COMPATIBLE) |
| MIL-DTL-5794 Revision C:2006 | MICROPHONE UNIT M-6A/UR AND MICROPHONE, CARBON M-51/UR (CARBON NOISE CANCELING) |
| IPC J STD 001 CHINESE : F | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| MIL-STD-883 Revision K:2016 | TEST METHOD STANDARD - MICROCIRCUITS |
| MIL-DTL-28754-10 Revision D:2014 | Connectors, Electrical, Modular, Connector, Type IV, 40 Pin, Contact Tails on 0.050 Centers |
| I.S. EN 61191-1:2013 | PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES (IEC 61191-1:2013 (EQV)) |
| IEC 61191-3:2017 | Printed board assemblies - Part 3: Sectional specification - Requirements for through-hole mount soldered assemblies |
| NASA MSFC STD 3012 : 2012 | ELECTRICAL, ELECTRONIC, AND ELECTROMECHANICAL (EEE) PARTS MANAGEMENT AND CONTROL REQUIREMENTS FOR MSFC SPACE FLIGHT HARDWARE |
| BS EN 61191-1:2013 | Printed board assemblies Generic specification. Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies |
| PD IEC/TR 62866:2014 | Electrochemical migration in printed wiring boards and assemblies. Mechanisms and testing |
| SAE AS 4461 : 2016 | ASSEMBLY AND SOLDERING CRITERIA FOR HIGH QUALITY/HIGH RELIABILITY SOLDERING WIRE AND CABLE TERMINATION IN AEROSPACE VEHICLES |
| AWS C3.11M/C3.11:2011 | SPECIFICATION FOR TORCH SOLDERING |
| IEC 61191-1:2013 | Printed board assemblies - Part 1: Generic specification - Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies |
| MIL-DTL-83502 Revision E:2007 | Sockets, Plug-in Electronic Components, Round Style, General Specification for |
| NASA STD 8739.3 : 1998 | SOLDERED ELECTRICAL CONNECTIONS |
| MIL-DTL-83731-13 Revision E:2014 | SWITCHES, TOGGLE, MINIATURE, RIGHT ANGLE (VERTICAL), PCB MOUNT, SINGLE POLE, LEVER SEAL, FLUX SEAL |
| DSCC 89065 : C | GENERAL SPECIFICATION FOR HIGH PERFORMANCE, HIGH DENSITY, TWO PIECE, PRINTED CIRCUIT BOARD CONNECTOR |
| EN 3155-040:2007 | Aerospace series - Electrical contacts used in elements of connection - Part 040: Contacts, electrical, coaxial, size 12, male, type D, solder, class R - Product standard |
| GEIA STD 0006 : 2008 | REQUIREMENTS FOR USING ROBOTIC HOT SOLDER DIP TO REPLACE THE FINISH ON ELECTRONIC PIECE PARTS |
| EN 61191-4:2017 | Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies |
| MIL-B-49030 Revision A:2010 | BATTERIES, DRY (ALKALINE) |
| BS EN 50390:2004 | Space product assurance. The manual soldering of high-reliability electrical connections |
| IEC TS 62647-23:2013 | Process management for avionics - Aerospace and defence electronic systems containing lead-free solder - Part 23: Rework and repair guidance to address the implications of lead-free electronics and mixed assemblies |
| IPC J STD 001 SPANISH : F | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| IPC A 610 GERMAN : E | ACCEPTABILITY OF ELECTRONIC ASSEMBLIES |
| MIL-DTL-15514 Revision G:2016 | Telephone Equipment, Sound Powered Telephone Handset, Headset-Chest Set, and Headset - Chest Set, Noise Attenuating |
| BS EN 61191-3:2017 | Printed board assemblies Sectional specification. Requirements for through-hole mount soldered assemblies |
| EN 50390:2004 | Space product assurance - The manual soldering of high-reliability electrical connections |
| MIL-DTL-55235 Revision A:2003 | CONNECTORS, COAXIAL, RADIO FREQUENCY, SERIES TPS, GENERAL SPECIFICATION |
| PD IEC/TS 62647-23:2013 | Process management for avionics. Aerospace and defence electronic systems containing lead-free solder Rework and repair guidance to address the implications of lead-free electronics and mixed assemblies |
| DD IEC PAS 62647-23 : DRAFT AUG 2011 | PROCESS MANAGEMENT FOR AVIONICS - AEROSPACE AND DEFENCE ELECTRONIC SYSTEMS CONTAINING LEAD-FREE SOLDER - PART 23: REWORK AND REPAIR GUIDANCE TO ADDRESS THE IMPLICATIONS OF LEAD-FREE ELECTRONICS AND MIXED ASSEMBLIES |
| MIL-DTL-28754-47 Revision C:2015 | CONNECTORS, ELECTRICAL MODULAR, TYPE 4, CONNECTOR, 100 PIN, RIGHT ANGLE CONTACT TAILS ON .100 CENTERS |
| MIL-PRF-32560 Base Document:2016 | COIL, RADIO FREQUENCY, SURFACE MOUNT, FIXED ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR |
| I.S. EN 50390:2004 | SPACE PRODUCT ASSURANCE - THE MANUAL SOLDERING OF HIGH-RELIABILITY ELECTRICAL CONNECTIONS |
| PREN 3155-039 : 200P1 | AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 039: CONTACTS, ELECTRICAL, COAXIAL, SIZE 16, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD |
| IPC J STD 001 FRENCH : F | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| DSCC 03024 : C | SHIELDING BEAD, ELECTRONIC, CHIP, FERRITE, HIGH RELIABILITY |
| BS EN 61191-4:2017 | Printed board assemblies Sectional specification. Requirements for terminal soldered assemblies |
| MIL-DTL-28754-101 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 0.6 PITCH, 250 CONTACT, CENTER |
| 15/30327712 DC : 0 | BS EN 61191-1 - PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES |
| DD IEC PAS 62686-1 : DRAFT JULY 2011 | PROCESS MANAGEMENT FOR AVIONICS - AEROSPACE QUALIFIED ELECTRONIC COMPONENTS (AQEC) - PART 1: GENERAL REQUIREMENTS FOR HIGH RELIABILITY INTEGRATED CIRCUITS AND DISCRETE SEMICONDUCTORS |
| MIL-DTL-18714 Revision F:2012 | PRIMER, ELECTRIC, MARK 45 MOD 1 |
| 11/30255124 DC : 0 | BS EN 61191-1 - PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES |
| I.S. EN 61191-2:2017 | PRINTED BOARD ASSEMBLIES - PART 2: SECTIONAL SPECIFICATION - REQUIREMENTS FOR SURFACE MOUNT SOLDERED ASSEMBLIES |
| MS27145 Revision C:2003 | CONNECTOR, PLUG, ELECTRICAL, NO. 14 AWG DOUBLE CONTACT, WATERPROOF |
| PREN 3155-041 : 200P1 | AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 041: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD |
| BS EN 3155-040:2007 | Aerospace series. Electrical contacts used in elements of connection Contacts, electrical, coaxial, size 12, male, type D, solder, class R. Product standard |
| NASA STD 8739.2 : 1999 | WORKMANSHIP STANDARD FOR SURFACE MOUNT TECHNOLOGY |
| MIL-DTL-28754-14 Revision D:2014 | Connectors, Electrical, Modular, Connector, Type IV, 20 Contact, Right Angle (for Die Cast Frame) |
| MIL-STD-202-210 Base Document:2015 | Method 210, Resistance to Soldering Heat |
| BS EN 3155-039:2007 | Aerospace series. Electrical contacts used in elements of connection Contacts, electrical, coaxial, size 16, female, type D, solder, class R. Product standard |
| 13/30295427 DC : 0 | BS IEC/PAS 61249-8-5 ED.1 - QUALIFICATION AND PERFORMANCE SPECIFICATION OF PERMANENT SOLDER MASK AND FLEXIBLE COVER MATERIALS |
| MIL-STD-750-1 Revision A:2015 | Environmental Test Methods for Semiconductor Devices Part 1: Test Methods 1000 Through 1999 |
| MIL-DTL-83731-14 Revision E:2014 | SWITCHES, TOGGLE, MINIATURE, RIGHT ANGLE (VERTICAL), PCB MOUNT, DOUBLE POLE, LEVER SEAL, FLUX SEAL |
| IEC PAS 62686-1:2011 | Process management for avionics - Aerospace qualified electronic components (AQEC) - Part 1: General requirements for high reliability integrated circuits and discrete semiconductors |
| IPC J STD 006 : C | REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDERS FOR ELECTRONIC SOLDERING APPLICATIONS |
| EN 61191-1:2013 | PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES (IEC 61191-1:2013) |
| MS35644 Revision G:2011 | FILLER NECK: FUEL TANK - MILITARY VEHICLES |
| MIL-DTL-28754-8 Revision D:2014 | Connectors, Electrical, Modular, Type IV, 40 Contact, Right Angle (for Die Cast Frame) |
| MIL-DTL-39024 Revision C:2014 | JACK, TIP (TEST POINT, PANEL OR PRINTED WIRING TYPE), GENERAL SPECIFICATION FOR |
| MIL-DTL-28754-61 Revision A:2016 | Connectors, Electrical, Modular, Type IV, Connector, 100 Pin, Center, Crossover, Contact Tails on .100 Centers (Ceramic Compatible) |
| IEC PAS 61249-8-5:2014 | Qualification and performance specification of permanent solder mask and flexible cover materials |
| MIL-DTL-13625 Revision G:2017 | SWITCHES, PULL; SWITCHES, PUSH; SWITCHES, BEAM SELECTING, HEADLIGHT: ELECTRICAL (28 VOLTS DC MAXIMUM, FOR MILITARY VEHICLES) |
| I.S. EN 3155-040:2007 | AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 040: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, MALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD |
| EN 61191-3:2017 | Printed board assemblies - Part 3: Sectional specification - Requirements for through-hole mount soldered assemblies |
| IEC PAS 62647-23:2011 | Process management for avionics - Aerospace and defence electronic systems containing lead-free solder - Part 23: Rework and repair guidance to address the implications of lead-free electronics and mixed assemblies |
| IEC 61191-4:2017 | Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies |
| BS EN 3155-041:2007 | Aerospace series. Electrical contacts used in elements of connection Contacts, electrical, coaxial, size 12, female, type D, solder, class R. Product standard |
| EN 3155-041:2007 | Aerospace series - Electrical contacts used in elements of connection - Part 041: Contacts, electrical, coaxial, size 12, female, type D, solder, class R - Product standard |
| PREN 3155-040 : 200P1 | AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 040: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, MALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD |
| MIL-DTL-28754-11 Revision F:2014 | Connectors, Electrical, Modular, Type IV, 40 Contact, Right Angle (for Solid or Dip Frame) |
| I.S. EN 61191-3:2017 | PRINTED BOARD ASSEMBLIES - PART 3: SECTIONAL SPECIFICATION - REQUIREMENTS FOR THROUGH-HOLE MOUNT SOLDERED ASSEMBLIES |
| I.S. EN 61191-4:2017 | PRINTED BOARD ASSEMBLIES - PART 4: SECTIONAL SPECIFICATION - REQUIREMENTS FOR TERMINAL SOLDERED ASSEMBLIES |
| MIL-DTL-21617 Revision B:2012 | CONNECTORS, PLUG AND RECEPTACLE, ELECTRICAL, RECTANGULAR, POLARIZED SHELL, MINIATURE TYPE, GENERAL SPECIFICATION FOR |
| MIL-DTL-28754-100 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 200 CONTACT, CENTER |
| MIL-PRF-31032 Revision C:2016 | Printed Circuit Board/Printed Wiring Board, General Specification for |
| PD IEC/PAS 61249-8-5:2014 | Qualification and performance specification of permanent solder mask and flexible cover materials |
| IPC J STD 075 : 0 | CLASSIFICATION OF NON-IC ELECTRONIC COMPONENTS FOR ASSEMBLY PROCESSES |
| DSCC 99002 : A | TRANSFORMER, SWITCHING |
| SAE AMS P 81728 : 2015 | PLATING, TIN-LEAD (ELECTRODEPOSITED) |
| MS90908 Revision C:2011 | FILLER TUBE, FUEL TANK - MILITARY VEHICLES |
| GEIA HB 0005-3 : 2008 | REWORK/REPAIR HANDBOOK TO ADDRESS THE IMPLICATIONS OF LEAD-FREE ELECTRONICS AND MIXED ASSEMBLIES IN AEROSPACE AND HIGH PERFORMANCE ELECTRONIC SYSTEMS |
| I.S. EN 3155-041:2007 | AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 041: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD |
| EN 3155-039:2007 | Aerospace series - Electrical contacts used in elements of connection - Part 039: Contacts, electrical, coaxial, size 16, female, type D, solder, class R - Product standard |
| IPC T 50 : M | TERMS AND DEFINITIONS FOR INTERCONNECTING AND PACKAGING ELECTRONIC CIRCUITS |
| IPC J STD 001 : F | REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| ISO/TS 16949:2009 | Quality management systems Particular requirements for the application of ISO 9001:2008 for automotive production and relevant service part organizations |
| EN 14582:2016 | Characterization of waste - Halogen and sulfur content - Oxygen combustion in closed systems and determination methods |
| IPC TM 650 : 0 | TEST METHODS MANUAL |
| IEC 61189-5:2006 | Test methods for electrical materials, interconnection structures and assemblies - Part 5: Test methods for printed board assemblies |
| IPC J STD 005 : A | REQUIREMENTS FOR SOLDERING PASTES |
| ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
| ISO 9455-17:2002 | Soft soldering fluxes — Test methods — Part 17: Surface insulation resistance comb test and electrochemical migration test of flux residues |
| GR 78 CORE : ISSUE 2 | GENERIC REQUIREMENTS FOR THE PHYSICAL DESIGN AND MANUFACTURE OF TELECOMMUNICATIONS PRODUCTS AND EQUIPMENT |
| ISO 10012:2003 | Measurement management systems — Requirements for measurement processes and measuring equipment |
| ISO 9001:2015 | Quality management systems — Requirements |
| IPC J STD 003 : C | SOLDERABILITY TESTS FOR PRINTED BOARDS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.