IEEE DRAFT C37.09 : D03F JAN 99
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
TEST PROCEDURE FOR AC HIGH-VOLTAGE CIRCUIT BREAKERS RATED ON A SYMMETRICAL CURRENT BASIS
06-26-1999
01-12-2013
1 Scope
2 Definitions
3 References
4 Design Tests
4.1 Maximum Voltage Tests
4.2 Power Frequency Tests
4.3 Continuous Current Tests
4.4 Dielectric Withstand Tests
4.5 Standard Operating Duty Tests
4.6 Interrupting Time Tests
4.7 Transient Recovery Voltage Tests
4.8 Short-Circuit Interrupting Tests
4.9 Load Current Switching Tests
4.10 Capacitor Current Switching Tests
4.11 Line closing Switching Surge Factor
4.12 Out-of-phase Switching Current Tests
4.13 Mechanical Endurance Tests
4.14 Control Voltage
4.15 Fluid Operating Pressure
4.16 Design Tests on Porcelain Components
4.17 Sealed Pressure Systems Leakage Tests
5 Production Tests
5.1 Types of tests
5.2 Current and Linear Coupler Tests
5.3 High-Voltage Circuit Breaker Tests
5.4 Gas Receiver Tests
5.5 Pressure Tests
5.6 Nameplate Check
5.7 Leakage Tests
5.8 Vacuum Integrity Tests
5.9 Resistors, Heaters and Coils Check Tests
5.10 Control and Secondary Wiring Check Tests
5.11 Clearance and Mechanical Adjustment Check Tests
5.12 Mechanical Operation Tests
5.13 Timing Tests
5.14 Stored Energy System Tests
5.15 Electrical Resistance of Current Path Test
5.16 Power Frequency Withstand Voltage Tests on
Major Insulation Components
5.17 Power Frequency Withstand Voltage Tests on Control
and Secondary Wiring
6 Conformance Test
6.1 Outdoor Circuit Breakers
6.2 Indoor Draw-Out Circuit Breakers
7 Standard Methods for Determining the Values of a
Sinusoidal Current Wave and a Power Frequency Recovery
Voltage
7.1 Currents
7.2 Power Frequency Recovery Voltage
Informative Annexes
A Suggested Short-Circuit Performance Data Form
B Table 1 and Notes from C37.09-1979
C Table 2 and Notes from C37.09-1979
Describes various tests made on AC high voltage indoor drawout and outdoor high-voltage circuit breakers. Gives accepted test procedures and defines tests for verification of assigned ratings under IEEE standards. Does not exclude more effective or equivalent rating demonstrating methods.
| DocumentType |
Draft
|
| PublisherName |
Institute of Electrical & Electronics Engineers
|
| Status |
Superseded
|
| SupersededBy |
| IEEE C37.013-1997 | IEEE Standard for AC High-Voltage Generator Circuit Breakers Rated on a Symmetrical Current Basis |
| IEEE C37.20.2-2015 | IEEE Standard for Metal-Clad Switchgear |
| IEEE C57.19.01-2000 | IEEE Standard Performance Characteristics and Dimensions for Outdoor Apparatus Bushings |
| IEEE C57.19.00 : 2004 | GENERAL REQUIREMENTS AND TEST PROCEDURE FOR POWER APPARATUS BUSHINGS |
| IEEE 4-2013 | IEEE Standard for High-Voltage Testing Techniques |
| IEEE C37.010-1999 | IEEE Application Guide for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis |
| ANSI C84.1 : 2016 | ELECTRIC POWER SYSTEMS AND EQUIPMENT - VOLTAGE RATINGS (60 HERTZ) |
| ANSI C37.54 : 1996 | FOR INDOOR ALTERNATING CURRENT HIGH-VOLTAGE CIRCUIT BREAKERS APPLIED AS REMOVABLE ELEMENTS IN METAL-ENCLOSED SWITCHGEAR ASSEMBLIES - CONFORMANCE TEST PROCEDURES |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| IEEE C37.011-2011 REDLINE | IEEE Guide for the Application of Transient Recovery Voltage for AC High-Voltage Circuit Breakers |
| IEEE C37.06-2009 | AC HIGH-VOLTAGE CIRCUIT BREAKERS RATED ON A SYMMETRICAL CURRENT BASIS - PREFERRED RATINGS AND RELATED REQUIRED CAPABILITIES |
| IEEE C37.015-2009 | IEEE Guide for the Application of Shunt Reactor Switching |
| IEEE C37.04-1999 | IEEE Standard Rating Structure for AC High-Voltage Circuit Breakers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.