IEC 62899-202:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Printed electronics - Part 202: Materials - Conductive ink
Hardcopy , PDF
English
02-25-2016
05-02-2023
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Atmospheric conditions for evaluation and
conditioning
5 Evaluation of properties of conductive ink
6 Evaluation of the properties of a conductive layer
7 Storage
Annex A (informative) - Examples of the four-point
probe for applying an appropriate weight
Annex B (informative) - Equation of correction factor F
Annex C (informative) - Influence of the measuring
position and the size of specimen on resistance
Bibliography
IEC 62899-202:2016(E) defines the terms and specifies the standard methods for characterisation and evaluation. This International Standard is applicable to conductive inks and conductive layer that are made from conductive inks.
| Committee |
TC 119
|
| DevelopmentNote |
Stability date: 2019. (02/2016)
|
| DocumentType |
Standard
|
| Pages |
31
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| BS IEC 62899-202:2016 | Identical |
| BS EN 55024:1998+A2:2003 | Identical |
| 18/30369151 DC : DRAFT MAY 2018 | BS EN 62899-202-7 - PRINTED ELECTRONICS - PART 202-7: MATERIALS - CONDUCTIVE INK - MEASUREMENT OF PEEL STRENGTH FOR PRINTED CONDUCTIVE LAYER ON FLEXIBLE SUBSTRATE |
| 18/30366168 DC : DRAFT APR 2018 | BS EN 62899-202-6 - PRINTED ELECTRONICS - PART 202-6: MATERIALS - CONDUCTIVE FILM - ENVIRONMENTAL TEST OF A PRINTED METAL BASED CONDUCTIVE LAYER ON FLEXIBLE SUBSTRATE |
| 17/30355474 DC : 0 | BS IEC 62899-202-3 ED.1.0 - PRINTED ELECTRONICS - PART 202-3: MATERIALS - CONDUCTIVE INK - MEASUREMENT OF SHEET RESISTANCE OF CONDUCTIVE FILMS (CONTACTLESS METHOD) |
| ISO 2811-1:2016 | Paints and varnishes — Determination of density — Part 1: Pycnometer method |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| ISO 13320:2009 | Particle size analysis — Laser diffraction methods |
| ISO 124:2014 | Latex, rubber — Determination of total solids content |
| ISO 3451-1:2008 | Plastics — Determination of ash — Part 1: General methods |
| ISO 3219:1993 | Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate |
| IEC 60695-4:2012 | Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical products |
| ISO 2884-1:1999 | Paints and varnishes — Determination of viscosity using rotary viscometers — Part 1: Cone-and-plate viscometer operated at a high rate of shear |
| ISO 11664-4:2008 | Colorimetry — Part 4: CIE 1976 L*a*b* Colour space |
| ISO 13468-1:1996 | Plastics — Determination of the total luminous transmittance of transparent materials — Part 1: Single-beam instrument |
| ISO 14887:2000 | Sample preparation — Dispersing procedures for powders in liquids |
| ISO 489:1999 | Plastics — Determination of refractive index |
| ISO 3679:2015 | Determination of flash no-flash and flash point — Rapid equilibrium closed cup method |
| ISO 13321:1996 | Particle size analysis — Photon correlation spectroscopy |
| ISO 2555:1989 | Plastics — Resins in the liquid state or as emulsions or dispersions — Determination of apparent viscosity by the Brookfield Test method |
| ISO 758:1976 | Liquid chemical products for industrial use — Determination of density at 20 degrees C |
| ISO 13322-1:2014 | Particle size analysis — Image analysis methods — Part 1: Static image analysis methods |
| ISO 13468-2:1999 | Plastics — Determination of the total luminous transmittance of transparent materials — Part 2: Double-beam instrument |
| ISO 2811-2:2011 | Paints and varnishes — Determination of density — Part 2: Immersed body (plummet) method |
| ISO 13319:2007 | Determination of particle size distributions — Electrical sensing zone method |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 291:2008 | Plastics — Standard atmospheres for conditioning and testing |
| ISO 5-3:2009 | Photography and graphic technology — Density measurements — Part 3: Spectral conditions |
| ISO 3664:2009 | Graphic technology and photography — Viewing conditions |
| ISO 13655:2017 | Graphic technology — Spectral measurement and colorimetric computation for graphic arts images |
| ISO 20998-1:2006 | Measurement and characterization of particles by acoustic methods — Part 1: Concepts and procedures in ultrasonic attenuation spectroscopy |
| ISO 9276-6:2008 | Representation of results of particle size analysis — Part 6: Descriptive and quantitative representation of particle shape and morphology |
| ISO 4576:1996 | Plastics — Polymer dispersions — Determination of sieve residue (gross particle and coagulum content) |
| ISO 5-2:2009 | Photography and graphic technology — Density measurements — Part 2: Geometric conditions for transmittance density |
| ISO 14782:1999 | Plastics — Determination of haze for transparent materials |
| ISO 14488:2007 | Particulate materials — Sampling and sample splitting for the determination of particulate properties |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.