IEC 60512-5:1992
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
05-04-2012
Superseded by
Language(s)
English - French, Spanish, Castilian
Published date
05-15-1992
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Contents
Foreword
Clause
Section Zero - General
0.1 Scope
0.2 Normative references
Section One - Impact Tests (Free Components)
1. Test 7a: Free fall (repeated)
2. Test 7b: Mechanical strength impact
Section Two - Static Load Tests (Fixed Components)
3. Test 8a: Static load, transverse
4. Test 8b: Static load, axial
5. Test 8c: Robustness of actuating lever
Section Three - Endurance Tests
6. Test 9a: Mechanical operation
7. Test 9b: Electrical load and temperature
8. Test 9c: Mechanical operation with electrical load
9. Test 9d: Durability of contact retention system and
seals (maintenance, ageing)
10. Test 9e: Current loading. cyclic
Section Four - Overload Tests
11. Test 10a: Electrical overload (switches)
12. Test 10b: Mechanical overload (switches)
13. Test 10c: Switching capacitive loads
14. Test 10d: Electrical overload (connectors)
Details standard test methods for impact tests, static load tests, endurance tests and overload tests.
| Committee |
TC 48/SC 48B
|
| DevelopmentNote |
Also numbered as BS 5772-5(1993) (08/2005)
|
| DocumentType |
Standard
|
| Pages |
43
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN IEC 60512-5:1994-05 | Identical |
| CEI 48-4 : 1ED 1983 | Identical |
| NEN IEC 60512-5 : 1999 | Identical |
| UNE-IEC 60512-5:2005 | Identical |
| BS EN 60512-8-2:2011 | Identical |
| NF EN 60512-12-5 : 2006 | Identical |
| BS EN 60512-8-3:2011 | Identical |
| NFC 93 400 : 85 AMD 1 88 | Identical |
| 02/206148 DC : 0 | IEC 60603-7-5. ED. 1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-5: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ (CAT 6, SHIELDED) |
| BS EN 61076-7:2001 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications Cable outlet accessories with assessed quality, including qualification and capability approval. Sectional specification |
| BS EN 61076-4-102:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part single-pole connectors, for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917 |
| CEI EN 60512-11-9 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-9: CLIMATIC TESTS TEST 11I: DRY HEAT |
| BS EN 60603-1:2000 | Connectors for frequencies below 3 MHz for use with printed boards Generic specification. General requirements and guide for the preparation of detail specifications with assessed quality |
| I.S. CECC 75301-802:1995 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ, TRAPEZOIDAL SHAPED SHELLS AND ROUND CONTACTS 01 MM WITH CRIMP, SOLDER AND PRESS-IN TERMINANONS FOR PRINTED BOARDS |
| I.S. EN 60512-11-10:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-10: CLIMATIC TESTS - TEST 11J: COLD |
| 00/201724 DC : DRAFT APR 2000 | IEC 61076-1 - CONNECTORS - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| IEC PAS 60603-7-3:2004 | Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz |
| 02/206147 DC : DRAFT AUG 2002 | IEC 60603-7-4 ED.1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-4: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ (CAT 6, UNSHIELDED) |
| BS EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| BS QC010000(1993) : AMD 10432 | HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS. CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE WITH PRINTED BOARDS - GENERIC SPECIFICATION: GENERAL REQUIREMENTS AND GUIDE FOR THE PREPARATION OF DETAIL SPECIFICATIONS, WITH ASSESSED QUALITY |
| FD ISO/TR 12369 : 2001 FD | AGRICULTURAL TRACTORS AND MACHINERY - ELECTRICAL POWER TRANSMISSION CONNECTORS |
| 03/100395 DC : DRAFT APR 2003 | EN 175101-809 - DETAIL SPECIFICATION - TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2,54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75 101-801, WITH ASSESSED QUALITY |
| 02/202649 DC : DRAFT JAN 2002 | IEC PAS 61076-3-111. ED.1 - CONNECTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 3-111: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED AND UNSHIELDED, FREE AND FIXED CONNECTORS, FOR INDUSTRIAL ENVIRONMENTS FOR FREQUENCIES UP TO 250 MHZ |
| IEC 60131-1:1984 | Lever switches. Part 1: General requirements and rules for the preparation of detail specifications |
| UNE-EN 50467:2012 | Railway applications - Rolling stock - Electrical connectors, requirements and test methods |
| I.S. EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| CEI 48-20 : 1998 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 3: DETAIL SPECIFICATION FOR A RANGE OF CONNECTORS WITH TRAPEZOIDAL SHAPED METAL SHELLS AND ROUND CONTACTS - REMOVABLE CRIMP CONTACT TYPES WITH CLOSED CRIMP BARRELS, REAR INSERTION/REAR EXTRACTION |
| I.S. EN 61076-4-103:1999 | CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2.5 MM |
| IEC 60603-14:1998 | Connectors for frequencies below 3 MHz for use with printed boards - Part 14: Detail specification for circular connectors for low-frequency audio and video applications such as audio, video and audio-visual equipment |
| EN 61076-5 : 2001 | CONNECTORS FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 5: IN-LINE SOCKETS WITH ASSESSED QUALITY - SECTIONAL SPECIFICATION |
| EN 196000 : 92 AMD 1 2001 | HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: ELECTROMECHANICAL SWITCHES |
| EN 60603-12:1998 | Connectors for frequencies below 3 MHz for use with printed boards - Part 12: Detail specification for dimensions, general requirements and tests for a range of sockets designed for use with integrated circuits |
| EN 61076-4-105:1998 | Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Printed board connectors - Section 105: Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication and audio industry |
| EN 60603-13:1998 | Connectors for frequencies below 3 MHz for use with printed boards - Part 13: Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in), with free connectors for non-accessible insulation displacement terminations (ID) |
| EN 61076-4-103:1999 | Connectors for use in d.c. low-frequency analogue and digital high speed data applications - Part 4-103: Printed board connectors with assessed quality - Detail specification for two-part connectors with shielding and a basic grid of 2,5 mm |
| EN 61076-4-102:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications - Part 4: Printed board connectors - Section 102: Detail specification for two-part single-pole connectors, for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917 |
| EN 61076-3-101:1997 | Connectors with assessed quality, for use in d.c. low-frequency analogue and in digital high-speed data applications - Part 3: Rectangular connectors - Section 101: Detail specification for a range of shielded connectors with trapezoidal shaped shells and non-removable rectangular contacts on a 1,27 mm x 2,54 mm centre-line |
| EN 60966-1:1999 | Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods |
| EN 60512-11-10:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold |
| EN 61076-7:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 7: Cable outlet accessories with assessed quality, including qualification and capability approval - Sectional specification |
| EN 60512-11-9:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat |
| EN 60130-17:1999 | Connectors for frequencies below 3 MHz - Part 17: Detail specification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries |
| IEC 60807-9:1993 | Rectangular connectors for frequencies below 3 MHz - Part 9: Detail specification for a range of peritelevision connectors |
| BS EN 60130-17:1999 | Connectors for frequencies below 3 MHz Detail specification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries |
| BS EN 61076-3-101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE |
| BS EN 196403:2000 | Harmonized systems of quality assessment for electronic components. Blank detail specification: push button switches. Assessment level Y |
| I.S. EN 60603-14:2000 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 14: DETAIL SPECIFICATION FOR CIRCULAR CONNECTORS FOR LOW-FREQUENCY AUDIO AND VIDEO APPLICATIONS SUCH AS AUDIO, VIDEO AND AUDIO-VISUAL EQUIPMENT |
| BS EN 60512-11-10:2002 | Connectors for electronic equipment. Tests and measurements. Climatic tests Test 11j. Cold |
| BS EN 60352-6:1998 | Solderless connections Solderless insulation piercing connections. General requirements, test methods and practical guidance |
| BS EN 61076-4-103:1999 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part connectors with shielding and a basic grid of 2,5 mm - Cable to board connectors, shielded against EMC ,grid 2,5 mm,for high speed data rates,for use with printed boards |
| CEI EN 50467 : 2013 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| 03/100167 DC : DRAFT JAN 2003 | IEC 60603-3-105 ED.1 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-105: DETAIL SPECIFICATION FOR 4 PAIR BALANCED, INDIVIDUALLY SHIELDED, FIXED AND FREE CONNECTORS WITH CHARACTERISTIC IMPEDENCE OF 100 OHMS, COVERING A FREQUENCY RANGE FROM DC TO 1500 MHZ |
| 04/30112325 DC : DRAFT APR 2004 | IEC 61076-3-104 ED.2 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-104: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 1000 MHZ |
| BS EN 196000:1993 | Harmonized system of quality assessment for electronic components. Generic specification. Electromechanical switches |
| PREN 50467 : DRAFT 2009 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| CEI EN 60352-3 : 1996 | SOLDERLESS CONNECTIONS - PART 3: SOLDERLESS ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| I.S. EN 60603-2:1998 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES |
| I.S. 1128:1991 | ELECTROMECHANICAL ALL-OR NOTHING RELAYS POLARIZED MONOSTABLE HERMETICALLY SEALED GENERAL PURPOSE RELAYS (DETAIL SPECIFICATION) |
| CEI EN 60603-1 : 2001 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 1: GENERIC SPECIFICATION; GENERAL REQUIREMENTS AND GUIDE FOR THE PREPARATION OF DETAIL SPECIFICATIONS, WITH ASSESSED QUALITY |
| IEC PAS 61076-3-110:2002 | Connectors for electronic equipment - Part 3-110: Detail specification for 8 way connectors for frequencies up to 600 MHz |
| IEC 60130-17:1998 | Connectors for frequencies below 3 MHz - Part 17: Detailspecification for interconnection devices which permit multi-directional mating, for use with rechargeable batteries |
| IEC 61076-4-105:1995 | Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Printed board connectors - Section 105 : Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication . |
| 03/100442 DC : DRAFT MAY 2003 | IEC 60352-2 ED.2 - SOLDERLESS CONNECTIONS - PART 2: SOLDERLESS CRIMPED CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| NF EN 61076 4 107 : 2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-107: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR SHIELDED TWO-PART CONNECTORS HAVING A BASIC GRID OF 2,0 MM, FIXED PART WITH SOLDER AND PRESS-IN TERMINATIONS FOR PRINTED BOARDS, FREE PART WITH NON-ACCESSIBLE INSULATION DISPLACEMENT AND CRIMP TERMINATIONS |
| 03/100166 DC : DRAFT JAN 2003 | IEC 60603-7-5 ED.1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-5: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ |
| EN 196110 : 2002 | SECTIONAL SPECIFICATION - ROTARY SWITCHES - CAPABILITY APPROVAL |
| BS EN 60603-2:1998 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features |
| BS EN 196103:2000 | Blank detail specification: Rotary switches. Assessment level Y |
| DD CLC/TS 50467:2008 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| CECC 75301-802 : 1994 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ, TRAPEZOIDAL SHAPED SHELLS AND ROUND CONTACTS 01 MM WITH CRIMP, SOLDER AND PRESS-IN TERMINANONS FOR PRINTED BOARDS |
| BS EN 60352-4:1995 | Solderless connections Solderless non-accessible insulation displacement connections. General requirements, test methods and practical guidance |
| 04/30124126 DC : DRAFT OCT 2004 | IEC 61076-2-104 ED.1 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 2-104: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR M8 CONNECTORS WITH SCREW OR SNAP-LOCKING FOR LOW VOLTAGE APPLICATIONS |
| CEI EN 60603-14 : 2000 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 14: DETAIL SPECIFICATION FOR CIRCULAR CONNECTORS FOR LOW-FREQUENCY AUDIO AND VIDEO APPLICATIONS SUCH AS AUDIO, VIDEO AND AUDIO-VISUAL EQUIPMENT |
| BS EN 60603-13:1998 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in) with free connectors for non-accessible insulation displacement terminations (ID) |
| BS EN 60603-12:1998 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for dimensions, general requirements and tests for a range of sockets designed for use with integrated circuits |
| BS EN 61076-4-105:1998 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication and audio industry |
| I.S. EN 61076-4-102:1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| I.S. EN 60130-17:1999 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 17: DETAIL SPECIFICATION FOR INTERCONNECTION DEVICES WHICH PERMIT MULTI-DIRECTIONAL MATING, FOR USE WITH RECHARGEABLE BATTERIES |
| I.S. EN 60512-11-9:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-9: CLIMATIC TESTS - TEST 11I: DRY HEAT |
| I.S. EN 61076-5:2002 | CONNECTORS FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 5: IN-LINE SOCKETS WITH ASSESSED QUALITY - SECTIONAL SPECIFICATION |
| IEC 60131-4:1987 | Lever switches. Part 4: Requirements for miniature toggle switches |
| CECC 75101-807 : 1994 | MODULAR TWO-PART CONNECTORS FOR PRINTED BOARDS AND BACKPLANES, GRIDOF 2.5 mm - ACCORDING TO IEC 917 (DETAIL SPECIFICATION) |
| NF EN 61076 3 101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTER-LINE |
| IEC PAS 61076-3-109:2001 | Connectors for electronic equipment - Part 3-109: Detail specification for two-part cable to board connector for high speed data application in a harsh industrial environment - Protection rate IP67 according to IEC 60529 |
| IEC 61020-3-2:1995 | Electromechanical switches for use in electronic equipment - Part3: Sectional specification for in-line package switches - Section2: Detail specification for dual-in-line package (DIP) switches,raised and recessed rocker actuated |
| I.S. CECC 75101-807:1994 | MODULAR TWO-PART CONNECTORS FOR PRINTED BOARDS AND BACKPLANES, GRID OF 2.5 MM - (ACCORDING TO IEC 917) (DETAIL SPECIFICATION) |
| S.R. CLC/TS 50467:2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| EN 175101-809:2004/corrigendum Jun. 2005 | DETAIL SPECIFICATION: TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2,54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75 101-801, WITH ASSESSED QUALITY |
| NF EN 60352-4 : 2001 | SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| EN 60352-3:1994 | Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance |
| EN 60352-4:1994/A1:2000 | SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| CEI EN 61076-4-103 : 2001 | CONNECTORS FOR USE IN D.C. LOW - FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2,5 MM |
| CEI 48-19 : 1998 | RECTANGULAR CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 2: DETAIL SPECIFICATION FOR A RANGE OF CONNECTORS, WITH ASSESSED QUALITY, WITH TRAPEZOIDAL SHAPED METAL SHELLS AND ROUND CONTACTS - FIXED SOLDER CONTACT TYPES |
| NF EN 61076 4 102 : 1998 | CONNECTORS WITH ASSESSED QUALITY FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTERING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| BS EN 175201-804:2000 | Harmonized system of quality assessment for electronic components Detail specification. Circular connectors. Round contacts, size diameter 1,6 mm, threaded coupling |
| CEI EN 61076-3-101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D/C/ LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE |
| ISO/IEC 14575:2000 | Information technology — Microprocessor systems — Heterogeneous InterConnect (HIC) (Low-Cost, Low-Latency Scalable Serial Interconnect for Parallel System Construction) |
| CEI EN 60130-17 : 2001 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ - PART 17: DETAIL SPECIFICATION FOR INTERCONNECTION DEVICES WHICH PERMIT MULTI-DIRECTIONAL MATING, FOR USE WITH RECHARGEABLE BATTERIES |
| CEI EN 60352-6 : 1998 | SOLDERLESS CONNECTIONS - PART 6: INSULATION PIERCING CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE |
| BS QC 480000(1995) : 1995 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C. LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 1: GENERIC SPECIFICATION |
| ANSI INCITS 293 : 1996 : R2006 | INFORMATION TECHNOLOGY - SERIAL STORAGE ARCHITECTURE PHYSICAL LAYER 1 (SSA-PH1) |
| BS EN 175101-802:2000 | Harmonized system of quality assessment for electronic components. Detail specification Two-part connectors for printed boards for high number of contacts with basic grid of 2,54 mm on 3 or 4 rows |
| CEI EN 60966-1 : 2001 | RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES - PART 1: GENERIC SPECIFICATION GENERAL REQUIREMENTS AND TEST METHODS |
| CEI 48-15 : 1998 | FLAT, QUICK-CONNECT TERMINATIONS |
| 11/30206085 DC : 0 | BS EN 60947-7-4 - LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PRINTED BOARD TERMINAL BLOCKS FOR COPPER CONDUCTORS |
| BS EN 60603-14:1999 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for circular connectors for low-frequency audio and video applications such as audio, video and audio-visual equipment |
| NF EN 61076 4 105 : 1999 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 105: DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION AND AUDIO INDUSTRY |
| 03/100336 DC : DRAFT MAR 2003 | IEC 60603-7-7 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-7: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 600 MHZ |
| 03/100165 DC : DRAFT JAN 2003 | IEC 60603-7-2 ED.1.0 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-2: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 100 MHZ |
| ANSI INCITS 293 : 1996 : R2001 | INFORMATION TECHNOLOGY - SERIAL STORAGE ARCHITECTURE PHYSICAL LAYER 1 (SSA-PH1) |
| I.S. EN 196110:2002 | SECTIONAL SPECIFICATION: ROTARY SWITCHES - CAPABILITY APPROVAL |
| I.S. EN 61076-4-104:1999 | CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GRID OF 2.0 MM WITH TERMINATIONS ON A MULTIPLE GRID OF 0.5 MM |
| IEC 60352-3:1993 | Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance |
| IEC 61076-5:2001 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications - Part 5: In-line sockets with assessed quality - Sectional specification |
| IEC 60352-6:1997 | Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance |
| IEC PAS 61076-3-111:2002 | Connectors for electronic equipment - Part 3-111: Detail specification for 8-way, shielded and unshielded, free and fixed connectors, for industrial environments for frequencies up to 250 MHz |
| IEC 61076-4-101:2001 | Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917 |
| IEC 61076-3-101:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high-speed data applications - Part 3: Rectangular connectors - Section 101: Detail specification for a range of shielded connectors with trapezoidal shaped shells and non-removable rectangular contacts on a 1,27 mm x 2,54 mm centre-line |
| IEC 61076-4-100:2001 | Connectors for electronic equipment - Part 4-100: Printed board connectors with assessed quality - Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes |
| IEC 60512-11-10:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-10: Climatic tests - Test 11j: Cold |
| IEC 60966-1:1999 | Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods |
| IEC 60603-12:1992 | Connectors for frequencies below 3 MHz for use with printed boards - Part 12: Detail specification for dimensions, general requirements and tests for a range of sockets designed for use with integrated circuits |
| IEC 61076-4-102:1997 | Connectors with assessed quality for use in d.c., low-frequencyanalogue and in digital high speed data applications - Part 4:Printed board connectors - Section 102: Detail specification fortwo-part single-pole connectors, for multiple uses on plug-inunits, with pre-centring, coding and early mating features, havinga metric grid in accordance with IEC 60917 |
| IEC 61076-3-100:1999 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 3-100: Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| IEC 60603-13:1995 | Connectors for frequencies below 3 MHz for use with printed boards - Part 13: Detail specification for two-part connectors of assessed quality, for printed boards for basic grid of 2,54 mm (0,1 in), with free connectors for non-accessible insulation displacement terminations (ID) |
| IEC 60512-11-9:2002 | Connectors for electronic equipment - Tests and measurements - Part 11-9: Climatic tests - Test 11i: Dry heat |
| EN 175201-804:1999 | Detail Specification: Circular connectors - Round contacts, size diameter 1,6 mm, threaded coupling |
| CLC/TS 50467 : 2008 COR 2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| 01/207165 DC : DRAFT OCT 2001 | IEC 61076-3-110 ED.1 - CONNECTORS FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED APPLICATIONS - PART 3-110: DETAIL SPECIFICATION FOR 8 WAY CONNECTORS FOR FREQUENCIES UP TO 600 MHZ [CATEGORY 7 DETAIL SPECIFICATION] |
| BS EN 61076-5:2001 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications In-line sockets with assessed quality. Sectional specification |
| CEI EN 60512-11-10 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-10: CLIMATIC TESTS - TEST 11J: COLD |
| 09/30208429 DC : 0 | BS EN 50467 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| 04/30124122 DC : DRAFT OCT 2004 | IEC 61076-2-101 ED.2 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 2-101: CIRCULAR CONNECTORS. DETAIL SPECIFICATION FOR M12 CONNECTORS WITH SCREW-LOCKING FOR LOW VOLTAGE APPLICATIONS |
| 13/30291609 DC : 0 | BS EN 60966-1 - RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND TEST METHODS |
| CEI EN 61076-4-104 : 2001 | CONNECTORS FOR USE IN D.C. LOW FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GIRD OF 2,0 MMS WITH TERMINATIONS ON A MULTIPLE GIRD OF 0,5 MM |
| BS EN 61076-4-107:2001 | Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| 04/30112330 DC : 0 | IEC 61076-3-113 ED.1 - CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-113: SCREENED, SERIAL MULTI-CONDUCTOR CABLE TO BOARD CONNECTORS SUITABLE FOR 10 GBIT/SEC DATA RATES |
| CEI EN 61076-4-102 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| BS EN 50467:2011 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| BS EN 61076-4-104:1999 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm - Detail specification for two part modular connectors (with optional shielding plates) for printed boards and backplanes, basic grid 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| BS EN 175101-809:2004 | Harmonized system of quality assessment for electronic components. Detail specification Two-part connectors for printed boards having a grid of 2,54 mm, short version in compliance with CECC 75 101-801, with assessed quality |
| BS EN 60512-11-9:2002 | Connectors for electronic equipment. Tests and measurements. Climatic tests Test 11i. Dry heat |
| 01/206171 DC : DRAFT AUG 2001 | |
| IEC PAS 61076-3-104:2002 | Connectors for electronic equipment - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors, for data transmissions with frequencies up to 600 MHz minimum |
| DIN EN 60352-3:1995-05 | Solderless connections - Part 3: Solderless accessible insulation displacement connections; general requirements, test methods and practical guidance (IEC 60352-3:1993); German version EN 60352-3:1994 |
| CEI EN 61076-4-105 : 2001 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION= AND AUDIO INDUSTRY |
| IEC 60807-1:1991 | Rectangular connectors for frequencies below 3 MHz - Part 1:Generic specification - General requirements and guide for thepreparation of detail specifications for connectors with assessedquality |
| I.S. EN 175101-809:2004 | DETAIL SPECIFICATION - TWO-PART CONNECTORS FOR PRINTED BOARDS HAVING A GRID OF 2.54 MM, SHORT VERSION IN COMPLIANCE WITH CECC 75101-801, WITH ASSESSED QUALITY |
| IEC 62847:2016 | Railway applications - Rolling stock - Electrical connectors - Requirements and test methods |
| IEC 60603-11:1992 | Connectors for frequencies below 3 MHz for use with printed boards - Part 11: Detail specification for concentric connectors (dimensions for free connectors and fixed connectors) |
| IEC 61076-4-104:1999 | Connectors for use in d.c., low frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| IEC 60603-2:1995 | Connectors for frequencies below 3 MHz for use with printed boards - Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features |
| EN 60603-2:1998/A1:2005 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES |
| EN 60352-6:1997 | Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance |
| EN 175101-802:1999 | Detail specification: Two-part connectors for printed boards for high number of contacts with basic grid of 2,54 mm on 3 or 4 rows |
| EN 61076-4-107:2001 | Connectors for electronic equipment - Part 4-107: Printed board connectors with assessed quality - Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 3-100: Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| EN 60603-1:1998 | Connectors for frequencies below 3 MHz for use with printed boards - Part 1: Generic specification - General requirements and guide for the preparation of detail specifications, with assessed quality |
| EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| EN 61076-4-104:1999 | Connectors for use in d.c. low-frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| EN 60603-14:1999 | Connectors for frequencies below 3 MHz for use with printed boards - Part 14: Detail specification for circular connectors for low-frequency audio and video applications such as audio, video and audio-visual equipment |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| IEC 60512-1:2001 | Connectors for electronic equipment - Tests and measurements - Part 1: General |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.