I.S. EN ISO/IEC 80079-34:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
EXPLOSIVE ATMOSPHERES - PART 34: APPLICATION OF QUALITY SYSTEMS FOR EQUIPMENT MANUFACTURE
Hardcopy , PDF
04-25-2020
English
01-01-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Quality management system
5 Management responsibility
6 Resource management
7 Product realization
8 Measurement, analysis and improvement
Annex A (informative) - Information relevant to particular
types of protection and specific products
Annex B (informative) - Verification criteria for elements
with non-measurable paths used as an integral part
of a type of protection
Bibliography
Annex ZA (normative) - Normative references to international
publications and the corresponding European
publications
Annex ZB (informative) - Information relevant to equipment and
protective systems according to standards harmonized
under Directive 94/9/EC
Annex ZY (informative) - Significant changes between this
European Standard and EN 13980:2002
Annex ZZ (informative) - Coverage of Essential Requirements of
EC Directives
Bibliography
Describes particular requirements and information for establishing and maintaining a quality system to manufacture Ex equipment including protective systems in accordance with the Ex certificate.
| DevelopmentNote |
Supersedes I.S. EN 13980. (07/2011)
|
| DocumentType |
Standard
|
| Pages |
58
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO/IEC 80079-34:2011 | Identical |
| ISO/IEC 80079-34:2011 | Identical |
| ISO/IEC 17000:2004 | Conformity assessment Vocabulary and general principles |
| ISO 3951-1:2013 | Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL |
| EN 15089:2009 | Explosion isolation systems |
| ISO/IEC 17050-1:2004 | Conformity assessment Supplier's declaration of conformity Part 1: General requirements |
| ISO 2738:1999 | Sintered metal materials, excluding hardmetals — Permeable sintered metal materials — Determination of density, oil content and open porosity |
| ISO/IEC 17021:2011 | Conformity assessment Requirements for bodies providing audit and certification of management systems |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
| ISO 4003:1977 | Permeable sintered metal materials — Determination of bubble test pore size |
| EN 14797:2006 | Explosion venting devices |
| EN 50050:2006 | Electrical apparatus for potentially explosive atmospheres - Electrostatic hand-held spraying equipment |
| EN 13463-6:2005 | Non-electrical equipment for use in potentially explosive atmospheres - Part 6: Protection by control of ignition source 'b' |
| IEC 60050-426:2008 | International Electrotechnical Vocabulary (IEV) - Part 426: Equipment for explosive atmospheres |
| EN 14986:2017 | Design of fans working in potentially explosive atmospheres |
| HD 429 : 200S1 | METHODS OF TEST FOR VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| EN 13463-8:2003 | Non-electrical equipment for potentially explosive atmospheres - Part 8: Protection by liquid immersion 'k' |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO/IEC 17050-2:2004 | Conformity assessment Supplier's declaration of conformity Part 2: Supporting documentation |
| EN 13463-2:2004 | Non-electrical equipment for use in potentially explosive atmospheres - Part 2: Protection by flow restricting enclosure 'fr' |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| ISO 16852:2016 | Flame arresters — Performance requirements, test methods and limits for use |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| EN ISO/IEC 17050-1:2010 | Conformity assessment - Supplier's declaration of conformity - Part 1: General requirements (ISO/IEC 17050-1:2004, corrected version 2007-06-15) |
| EN ISO/IEC 17000:2004 | Conformity assessment - Vocabulary and general principles (ISO/IEC 17000:2004) |
| EN 13463-5:2011 | Non-electrical equipment intended for use in potentially explosive atmospheres - Part 5: Protection by constructional safety 'c' |
| EN 13463-3:2005 | Non-electrical equipment for use in potentially explosive atmospheres - Part 3: Protection by flameproof enclosure 'd' |
| EN 24003:1993 | Permeable sintered metal materials - Determination of bubble test pore size (ISO 4003:1977) |
| EN ISO/IEC 17021:2011 | Conformity assessment - Requirements for bodies providing audit and certification of management systems (ISO/IEC 17021:2011) |
| EN ISO/IEC 17050-2:2004 | Conformity assessment - Supplier's declaration of conformity - Part 2: Supporting documentation (ISO/IEC 17050-2:2004) |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| EN ISO 16852:2016 | Flame arresters - Performance requirements, test methods and limits for use (ISO 16852:2016) |
| EN ISO 2738:1999 | Sintered metal materials, excluding hardmetals - Permeable sintered metal materials - Determination of density, oil content and open porosity (ISO 2738:1999) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.