I.S. EN ISO 5361:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ANAESTHETIC AND RESPIRATORY EQUIPMENT - TRACHEAL TUBES AND CONNECTORS (ISO/DIS 5361:2014)
Hardcopy , PDF
09-18-2023
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements for tracheal tubes and
tracheal tube connectors
5 Specific requirements for tracheal tubes and
tracheal tube connectors
6 Additional requirement for tracheal tubes
with a Murphy eye
7 Requirements for tracheal tubes with tracheal
tube connectors supplied sterile
8 Marking
Annex A (informative) - Rationale
Annex B (normative) - Determination of cuff
diameter
Annex C (normative) - Test method for cuffed
tube collapse
Annex D (normative) - Test method for cuff
herniation
Annex E (informative) - Guidance on design of
tracheal tube connectors
Annex F (informative) - Hazard identification
for risk assessment
Annex G (normative) - Test method for tracheal
seal
Annex H (normative) - Test method to determine
kink resistance
Bibliography
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 93/42/EEC
Gives essential performance and safety requirements for oro-tracheal and naso-tracheal tubes and tracheal tube connectors.
| DevelopmentNote |
Supersedes I.S. EN 1782. (11/2013)
|
| DocumentType |
Standard
|
| Pages |
62
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 5361:2016 | Identical |
| ISO 5361:2016 | Identical |
| ISO 11990-1:2011 | Lasers and laser-related equipment Determination of laser resistance of tracheal tubes Part 1: Tracheal tube shaft |
| ISO 14408:2016 | Tracheal tubes designed for laser surgery — Requirements for marking and accompanying information |
| ISO 11137-1:2006 | Sterilization of health care products Radiation Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 11990-2:2010 | Lasers and laser-related equipment Determination of laser resistance of tracheal tubes Part 2: Tracheal tube cuffs |
| ISO 15223-2:2010 | Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation |
| ISO 11135:2014 | Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices |
| EN ISO 5356-1:2015 | Anaesthetic and respiratory equipment - Conical connectors - Part 1: Cones and sockets (ISO 5356-1:2015) |
| ISO 5356-1:2015 | Anaesthetic and respiratory equipment Conical connectors Part 1: Cones and sockets |
| IEC 62366:2007+AMD1:2014 CSV | Medical devices - Application of usability engineering to medical devices |
| EN ISO 11135:2014 | Sterilization of health-care products - Ethylene oxide - Requirements for the development, validation and routine control of a sterilization process for medical devices (ISO 11135:2014) |
| EN 1041:2008+A1:2013 | Information supplied by the manufacturer of medical devices |
| ANSI Z79.16 : 1983 | CUFFED OROTRACHEAL AND NASOTRACHEAL TUBES FOR PROLONGED USE, |
| ISO 10993-1:2009 | Biological evaluation of medical devices Part 1: Evaluation and testing within a risk management process |
| ISO 14155:2011 | Clinical investigation of medical devices for human subjects Good clinical practice |
| ISO/TR 11991:1995 | Guidance on airway management during laser surgery of upper airway |
| ISO 14971:2007 | Medical devices Application of risk management to medical devices |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| ISO 11607-1:2006 | Packaging for terminally sterilized medical devices Part 1: Requirements for materials, sterile barrier systems and packaging systems |
| ISO 4135:2001 | Anaesthetic and respiratory equipment Vocabulary |
| ASTM F 1242 : 1996 : EDT 1 | Standard Specification for Cuffed and Uncuffed Tracheal Tubes (Withdrawn 2002) |
| ISO 15223-1:2016 | Medical devices Symbols to be used with medical device labels, labelling and information to be supplied Part 1: General requirements |
| ISO 594-1:1986 | Conical fittings with a 6 % (Luer) taper for syringes, needles and certain other medical equipment Part 1: General requirements |
| ASTM F 640 : 2012 : REDLINE | Standard Test Methods for Determining Radiopacity for Medical Use |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.