I.S. EN ISO 527-2:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 2: TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS (ISO 527-2:2012)
Hardcopy , PDF
English
01-01-2012
09-11-2025
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle and methods
5 Apparatus
6 Test specimens
7 Conditioning
8 Procedure
9 Calculation and expression of results
10 Precision
11 Test report
Annex A (informative) - Small specimens
Annex B (informative) - Precision statement
Bibliography
Defines the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.
| Committee |
ISO/TC 61
|
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN ISO 527-2:1996 | Identical |
| NS EN ISO 527-2 : 2012 | Identical |
| NF EN ISO 527-2 : 2012 | Identical |
| EN ISO 527-2:2012 | Identical |
| NEN EN ISO 527-2 : 2012 | Identical |
| ISO 527-2:2012 | Identical |
| NBN EN ISO 527-2 : 2012 | Identical |
| ONORM EN ISO 527-2 : 2012 | Identical |
| DIN EN ISO 527-2:2012-06 | Identical |
| UNE-EN ISO 527-2:1997 | Identical |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| ISO 294-3:2002 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 1926:2009 | Rigid cellular plastics — Determination of tensile properties |
| ISO 294-2:1996 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 20753:2008 | Plastics — Test specimens |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.