I.S. EN ISO 3506-2:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS
Hardcopy , PDF
05-16-2020
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Symbols
4 Designation, marking and finish
5 Chemical composition
6 Mechanical properties
7 Test methods
Annex A (informative) - Description of the groups and grades
of stainless steels
Annex B (informative) - Stainless steel composition
specifications
Annex C (informative) - Stainless steels for cold heading
and extruding
Annex D (informative) - Austenitic stainless steels with
particular resistance to chloride
induced stress corrosion
Annex E (informative) - Mechanical properties at elevated
temperatures; application at low
temperatures
Annex F (informative) - Time-temperature diagram of
intergranular corrosion in austenitic
stainless steels, grade A2 (18/8
steels)
Annex G (informative) - Magnetic properties for austenitic
stainless steels
Bibliography
Describes the mechanical properties of nuts made of austenitic, martensitic and ferritic steel grades of corrosion-resistant stainless steels, when tested over an ambient temperature range of 10 degrees C to 35 degrees C.
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN ISO 3506-2 : 2010 | Identical |
| DIN EN ISO 3506-2:2010-04 | Identical |
| ISO 3506-2:2009 | Identical |
| EN ISO 3506-2:2009 | Identical |
| UNE-EN ISO 3506-2:2010 | Identical |
| NS EN ISO 3506-2 : 2009 | Identical |
| NBN EN ISO 3506-2 : 2010 | Identical |
| UNI EN ISO 3506-2 : 2010 | Identical |
| NF EN ISO 3506-2 : 2010 | Identical |
| BS EN ISO 3506-2:2009 | Identical |
| NEN EN ISO 3506-2 : 2009 | Identical |
| SN EN ISO 3506-2 : 2010 | Identical |
| ISO 272:1982 | Fasteners — Hexagon products — Widths across flats |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 683-13:1974 | Heat-treated steels, alloy steels and free-cutting steels Part 13: Wrought stainless steels |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| ISO 16426:2002 | Fasteners — Quality assurance system |
| ISO 898-6:1994 | Mechanical properties of fasteners Part 6: Nuts with specified proof load values Fine pitch thread |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ISO 68-1:1998 | ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| ISO 8044:2015 | Corrosion of metals and alloys Basic terms and definitions |
| ISO 16048:2003 | Passivation of corrosion-resistant stainless-steel fasteners |
| ISO 3651-1:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in nitric acid medium by measurement of loss in mass (Huey test) |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 4954:1993 | Steels for cold heading and cold extruding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.