I.S. EN ISO 23936-2:2011
Current
The latest, up-to-date edition.
PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - NON-METALLIC MATERIALS IN CONTACT WITH MEDIA RELATED TO OIL AND GAS PRODUCTION - PART 2: ELASTOMERS (ISO 23936-2:2011)
Hardcopy , PDF
English
01-01-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 Technical requirements
5 Documentation requirements
6 Requirements for manufacturers
7 Qualification of elastomer materials
(ageing and RGD)
8 Qualification of elastomeric materials in
bonded flexible hose
9 Qualification of elastomeric materials in
other large components
Annex A (normative) - Test media, conditions,
equipment and procedures for ageing of
elastomeric materials
Annex B (normative) - Test media, conditions,
equipment and procedures for rapid gas
decompression testing of elastomeric
materials
Annex C (informative) - Most commonly used
elastomeric materials
Annex D (normative) - Procedure for estimation
of material service life using the Arrhenius
relationship
Annex E (informative) - Physical and chemical
ageing
Annex F (informative) - Rapid gas decompression
(RGD)
Bibliography
Specifies general principles and provides requirements and recommendations for the selection and qualification of non-metallic materials for service in equipment used in oil and gas production environments, where the failure of such equipment could pose a risk to the health and safety of the public and personnel, or to the environment.
| DocumentType |
Standard
|
| Pages |
81
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN ISO 23936-2:2011 | Identical |
| ISO 23936-2:2011 | Identical |
| ASTM D 297 : 2015 : REDLINE | Standard Test Methods for Rubber Products—Chemical Analysis |
| ISO 1432:2013 | Rubber, vulcanized or thermoplastic Determination of low-temperature stiffening (Gehman test) |
| ISO 2921:2011 | Rubber, vulcanized Determination of low-temperature retraction (TR test) |
| ISO 7619-1:2010 | Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 1: Durometer method (Shore hardness) |
| ISO 11346:2014 | Rubber, vulcanized or thermoplastic — Estimation of life-time and maximum temperature of use |
| API 6J1 : 2000 | ELASTOMER LIFE ESTIMATION TESTING PROCEDURES |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| ASTM D 1414 : 2015 : REDLINE | Standard Test Methods for Rubber O-Rings |
| API 6A : 2010 | SPECIFICATION FOR WELLHEAD AND CHRISTMAS TREE EQUIPMENT |
| API SPEC 17K : 2017 | SPECIFICATION FOR BONDED FLEXIBLE PIPE |
| ASTM D 3032 : 2016 : REDLINE | Standard Test Methods for Hookup Wire Insulation |
| API 14A : 2015 | SPECIFICATION FOR SUBSURFACE SAFETY VALVE EQUIPMENT |
| ISO 23936-1:2009 | Petroleum, petrochemical and natural gas industries — Non-metallic materials in contact with media related to oil and gas production — Part 1: Thermoplastics |
| ISO 16070:2005 | Petroleum and natural gas industries Downhole equipment Lock mandrels and landing nipples |
| ISO 34-1:2015 | Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces |
| ISO 14310:2008 | Petroleum and natural gas industries — Downhole equipment — Packers and bridge plugs |
| ISO 13533:2001 | Petroleum and natural gas industries — Drilling and production equipment — Drill-through equipment |
| ISO 10423:2009 | Petroleum and natural gas industries Drilling and production equipment Wellhead and christmas tree equipment |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 3601-1:2012 | Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes |
| ISO 36:2017 | Rubber, vulcanized or thermoplastic Determination of adhesion to textile fabrics |
| ISO 3601-3:2005 | Fluid power systems O-rings Part 3: Quality acceptance criteria |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 2781:2008 | Rubber, vulcanized or thermoplastic Determination of density |
| ASTM D 1418 : 2017 : REDLINE | Standard Practice for Rubber and Rubber Latices—Nomenclature |
| ISO 13628-10:2005 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 10: Specification for bonded flexible pipe |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.