I.S. EN ISO 19085-3:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WOODWORKING MACHINES - SAFETY REQUIREMENTS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES (ISO 19085-3:2017)
Hardcopy , PDF
01-20-2022
English
01-01-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and measures for controls
6 Safety requirements and measures for protection
against mechanical hazards
7 Safety requirements and measures for protection
against other hazards
8 Information for use
Annex A (informative) - Performance levels required
Annex B (normative) - Test for braking function
Annex C (normative) - Stability test for displaceable machines
Annex D (normative) - Impact test for guards
Annex E (normative) - Noise emission measurement for
machines not in ISO 7960
Annex F (normative) - Impact test for curtains
Annex G (normative) - Wear test for curtains
Annex H (normative) - Dynamic test for pressure-sensitive
bumpers, edges, trip bars, trip plates
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
Provides the safety requirements and measures for numerically controlled (NC) boring machines, NC routing machines and NC combined boring/routing machines, hereinafter referred to as 'machines'.
| DevelopmentNote |
Supersedes I.S. EN 848-3. (02/2018)
|
| DocumentType |
Standard
|
| Pages |
86
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 19085-3:2017 | Identical |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
| ISO 19085-1:2017 | Woodworking machines Safety Part 1: Common requirements |
| EN 847-2:2017 | Tools for woodworking - Safety requirements - Part 2: Requirements for the shank of shank mounted milling tools/circular saw blades |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| EN 847-1:2017 | Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13856-3:2013 | Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| IEC 61800-5-2:2016 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.