I.S. EN ISO 16090-1:2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MACHINE TOOLS SAFETY - MACHINING CENTRES, MILLING MACHINES, TRANSFER MACHINES - PART 1: SAFETY REQUIREMENTS (ISO 16090-1:2017)
Hardcopy , PDF
07-12-2023
English
10-09-2018
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective/risk reduction
measures
6 Information for use
Annex A (normative) - Impact test method for guards
on machines
Annex B (informative) - Equipment for impact test and
examples of tested materials
Annex C (informative) - Illustrative figures as examples
of machines
Annex D (informative) - Illustrative figures as examples
of guards
Annex E (informative) - Examples of the integration of
exhaust and extinguishing systems when using
combustible coolants or combustible dust
Annex F (informative) - Provisions when using combustible
coolants and combustible dust
Annex G (normative) - Gravity-loaded axes
Annex H (informative) - Examples: Concept for leaving/returning
to a cabin (control station) at Group 3 and Group
4 machines
Annex I (informative) - Typical demand rates of safety
functions for calculations according to Table 5
and Annex J
Annex J (normative) - Safety functions
Annex K (normative) - Noise emission measurement
Bibliography
Describes the technical safety requirements and protective measures for the design, construction and supply (including installation and dismantling, with arrangements for transport and maintenance) of stationary milling machines, including machines capable of performing boring operations, machining centers and transfer machines which are intended to cut cold metal, and other non-combustible cold materials except for wood or materials with physical characteristics similar to those of wood as defined in ISO 19085-1, and for glass, stone and engineered/agglomerated materials as defined in EN 14618.
| Committee |
TC 39
|
| DevelopmentNote |
Supersedes I.S. EN 12417, I.S. EN 13128 & I.S. EN 14070. (04/2018)
|
| DocumentType |
Standard
|
| Pages |
170
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 16090-1:2017 | Identical |
| EN ISO 16090-1:2018 | Identical |
| EN 1005-4:2005+A1:2008 | Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery |
| ISO 13855:2010 | Safety of machinery Positioning of safeguards with respect to the approach speeds of parts of the human body |
| ISO 9241-400:2007 | Ergonomics of humansystem interaction Part 400: Principles and requirements for physical input devices |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 14119:2013 | Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| ISO 11161:2007 | Safety of machinery — Integrated manufacturing systems — Basic requirements |
| ISO 14120:2015 | Safety of machinery Guards General requirements for the design and construction of fixed and movable guards |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 16089:2015 | Machine tools Safety Stationary grinding machines |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 50370-2:2003 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| ISO 9355-1:1999 | Ergonomic requirements for the design of displays and control actuators — Part 1: Human interactions with displays and control actuators |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 14738:2002 | Safety of machinery — Anthropometric requirements for the design of workstations at machinery |
| EN 1005-1:2001+A1:2008 | Safety of machinery - Human physical performance - Part 1: Terms and definitions |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| ISO 9241-20:2008 | Ergonomics of human-system interaction Part 20: Accessibility guidelines for information/communication technology (ICT) equipment and services |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| ISO 14118:2000 | Safety of machinery Prevention of unexpected start-up |
| ISO 13851:2002 | Safety of machinery Two-hand control devices Functional aspects and design principles |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| EN 14618:2009 | Agglomerated stone - Terminology and classification |
| EN 12445:2000 | Industrial, commercial and garage doors and gates - Safety in use of power operated doors - Test methods |
| ISO 13856-2:2013 | Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars |
| IEC 61000-6-3:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments |
| ISO 19085-1:2017 | Woodworking machines Safety Part 1: Common requirements |
| ISO 14159:2002 | Safety of machinery — Hygiene requirements for the design of machinery |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| ISO 15641:2001 | Milling cutters for high speed machining — Safety requirements |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 61496-3:2008 | Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR) |
| ISO 16156:2004 | Machine-tools safety — Safety requirements for the design and construction of work holding chucks |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| ISO 9355-3:2006 | Ergonomic requirements for the design of displays and control actuators — Part 3: Control actuators |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| IEC 61000-6-4:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments |
| ISO 13854:2017 | Safety of machinery — Minimum gaps to avoid crushing of parts of the human body |
| ISO 13856-1:2013 | Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 15534-1:2000 | Ergonomic design for the safety of machinery — Part 1: Principles for determining the dimensions required for openings for whole-body access into machinery |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| ISO 13856-3:2013 | Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| ISO 11228-1:2003 | Ergonomics Manual handling Part 1: Lifting and carrying |
| EN 50370-1:2005 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission |
| IEC TS 62046:2008 | Safety of machinery - Application of protective equipment to detect the presence of persons |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 15534-2:2000 | Ergonomic design for the safety of machinery — Part 2: Principles for determining the dimensions required for access openings |
| ISO 6385:2016 | Ergonomics principles in the design of work systems |
| ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| ISO 9241-410:2008 | Ergonomics of human-system interaction Part 410: Design criteria for physical input devices |
| IEC 61800-5-2:2016 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| ISO 9355-2:1999 | Ergonomic requirements for the design of displays and control actuators — Part 2: Displays |
| IEC 61496-2:2013 | Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) |
| ISO 19353:2015 | Safety of machinery Fire prevention and fire protection |
| ISO 230-5:2000 | Test code for machine tools Part 5: Determination of the noise emission |
| ISO 23125:2015 | Machine tools — Safety — Turning machines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.