I.S. EN ISO 15874-5:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM (ISO 15874-5:2013)
Hardcopy , PDF
01-30-2020
03-05-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated
terms
4 Fitness for purpose of the joints and the piping
system
Bibliography
Describes the characteristics of the fitness for purpose of polypropylene (PP) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application.
| Committee |
TC 155
|
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 15874-5:2013 | Identical |
| NBN EN ISO 15874-5 : 2013 | Identical |
| UNE-EN ISO 15874-5:2013 | Identical |
| DIN EN ISO 15874-5:2013-06 | Identical |
| UNI EN ISO 15874-5 : 2013 | Identical |
| SN EN ISO 15874-5:2013 | Identical |
| NEN EN ISO 15874-5 : 2013 | Identical |
| BS EN ISO 15874-5 : 2013 | Identical |
| ISO 15874-5:2013 | Identical |
| NS EN ISO 15874-5 : 2013 | Identical |
| NF EN ISO 15874-5 : 2013 | Identical |
| ONORM EN ISO 15874-5 : 2013 | Identical |
| DIN EN ISO 15874-5:2004-03 | Identical |
| ISO 19892:2011 | Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 15874-1:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 19893:2011 | Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling |
| ISO 15874-2:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes |
| EN 713:1993 | Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| CEN/TR 12108:2012 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| EN 12294:1999 | Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum |
| ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity |
| EN 712:1993 | Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.