I.S. EN ISO 13849-2:2012
Current
The latest, up-to-date edition.
SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 2: VALIDATION (ISO 13849-2:2012)
Hardcopy , PDF
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Validation process
5 Validation by analysis
6 Validation by testing
7 Validation of safety requirements specification
for safety functions
8 Validation of safety functions
9 Validation of performance levels and categories
10 Validation of environmental requirements
11 Validation of maintenance requirements
12 Validation of technical documentation and
information for use
Annex A (informative) - Validation tools for
mechanical systems
Annex B (informative) - Validation tools for
pneumatic systems
Annex C (informative) - Validation tools for
hydraulic systems
Annex D (informative) - Validation tools for
electrical systems
Annex E (informative) - Example of validation
of fault behaviour and diagnostic means
Bibliography
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Defines the procedures and conditions to be followed for the validation by analysis and testing of: - the specified safety functions, - the category achieved, and - the performance level achieved by the safety-related parts of a control system (SRP/CS) designed in accordance with ISO 13849-1.
| DocumentType |
Standard
|
| Pages |
93
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| BS EN ISO 13849-2:2012 | Identical |
| NS EN ISO 13849-2 : 2012 | Identical |
| ISO 13849-2:2012 | Identical |
| UNE-EN ISO 13849-2:2013 | Identical |
| UNI EN ISO 13849-2 : 2013 | Identical |
| NEN EN ISO 13849-2 : 2012 | Identical |
| NF EN ISO 13849-2 : 2012 | Identical |
| DIN EN ISO 13849-2:2013-02 | Identical |
| SN EN ISO 13849-2:2013 | Identical |
| EN ISO 13849-2:2012 | Identical |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| ISO 4079-1:2001 | Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 1: Oil-based fluid applications |
| ISO 13855:2010 | Safety of machinery Positioning of safeguards with respect to the approach speeds of parts of the human body |
| ISO 14119:2013 | Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
| ISO 4960:2007 | Cold-reduced carbon steel strip with a mass fraction of carbon over 0,25 % |
| ISO 11161:2007 | Safety of machinery — Integrated manufacturing systems — Basic requirements |
| EN 50205:2002 | Relays with forcibly guided (mechanically linked) contacts |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 61131-1:2003 | Programmable controllers - Part 1: General information |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| IEC 60893-1:2004 | Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| IEC 61078:2016 | Reliability block diagrams |
| ISO 14118:2000 | Safety of machinery Prevention of unexpected start-up |
| ISO 13851:2002 | Safety of machinery Two-hand control devices Functional aspects and design principles |
| IEC 61165:2006 | Application of Markov techniques |
| IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV | Low-voltage fuses - Part 1: General requirements |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| EN 952:1999 | Door leaves - General and local flatness - Measurement method |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| IEC 61131-2:2017 | Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| IEC 61800-5-2:2016 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.