I.S. EN ISO 13628-11:2008
Current
The latest, up-to-date edition.
PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 11: FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS
Hardcopy , PDF
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, abbreviated terms, definitions and symbols
3.1 Terms and definitions
3.2 Symbols and abbreviated terms
4 System, pipe, and component description
4.1 Introduction
4.2 Flexible pipe systems
4.3 Flexible pipe description
4.4 Ancillary components
5 Pipe design considerations
5.1 General
5.2 Design overview
5.3 Failure modes
5.4 Design criteria
5.5 Load cases
6 Materials
6.1 Scope
6.2 Materials - Unbonded pipe
6.3 Materials - Bonded pipe
6.4 Alternative materials
6.5 Polymer/elastomer test procedures
6.6 Metallic-material test requirements
7 System design considerations
7.1 General
7.2 General system requirements
7.3 Flowline design requirements
7.4 Riser design requirements
7.5 Ancillary components
7.6 System interfaces
8 Analysis considerations
8.1 Introduction
8.2 Analysis techniques
8.3 Loads
8.4 Global-response evaluation
9 Prototype testing
9.1 General
9.2 Design programmes
9.3 Classification of prototype tests
9.4 Test requirements
9.5 Test protocol
9.6 Procedures - Standard prototype tests
9.7 Procedures - Special prototype tests
10 Manufacturing
10.1 General
10.2 Manufacturing - Unbonded pipe
10.3 Manufacturing - Bonded pipe
10.4 Marking
10.5 Storage
11 Handling, transportation, and installation
11.1 General
11.2 Handling
11.3 Transportation
11.4 Installation
11.5 Pre-commissioning and commissioning
12 Retrieval and reuse
12.1 General
12.2 Retrieval
12.3 Reuse
13 Integrity and condition monitoring
13.1 General
13.2 General philosophy
13.3 Failure modes and potential pipe defects
13.4 Monitoring methods
13.5 Recommendations
Annex A (normative) - Flexible-pipe high-temperature end-fitting
qualification test protocol -
Volatile-content polymers
Annex B (normative) - Polyvinylidene fluoride (PVDF) coupon
crude-oil exposure-test procedure
Annex C (normative) - Flexible-pipe high-temperature end-fitting
qualification test procedures:
Low-volatile-content polymers
Annex D (normative) - Polymer coupon crude-oil exposure-test
procedure
Bibliography
Gives guidelines for the design, analysis, manufacture, testing, installation and operation of flexible pipes and flexible systems for onshore, subsea and marine applications.
| DocumentType |
Standard
|
| Pages |
226
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| ISO 13628-11:2007 | Identical |
| ISO 12086-1:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 1: Designation system and basis for specifications |
| API 2A WSD : 2014 | PLANNING, DESIGNING, AND CONSTRUCTING FIXED OFFSHORE PLATFORMS - WORKING STRESS DESIGN |
| ISO 1874-1:2010 | Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system and basis for specification |
| ISO 13628-2:2006 | Petroleum and natural gas industries Design and operation of subsea production systems Part 2: Unbonded flexible pipe systems for subsea and marine applications |
| API TR 17TR2 : 2003 | THE AGEING OF PA-11 IN FLEXIBLE PIPES |
| ISO 13628-3:2000 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 3: Through flowline (TFL) systems |
| NACE TM 02 84 : 2016 | EVALUATION OF PIPELINE AND PRESSURE VESSEL STEELS FOR RESISTANCE TO HYDROGEN-INDUCED CRACKING |
| API 6A : 2010 | SPECIFICATION FOR WELLHEAD AND CHRISTMAS TREE EQUIPMENT |
| NACE TM 01 77 : 2016 | LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS |
| ASTM D 413 : 1998 | Standard Test Methods for Rubber Property-Adhesion to Flexible Substrate |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| API 2RD : 2013 | DYNAMIC RISERS FOR FLOATING PRODUCTION SYSTEMS |
| ASTM D 2143 : 2015 : REDLINE | Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe |
| ISO 10931-1:1997 | Plastics piping systems for industrial applications Poly(vinylidene fluoride) (PVDF) Part 1: General |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| API RP 17B : 2014 | RECOMMENDED PRACTICE FOR FLEXIBLE PIPE |
| ISO 15156-1:2015 | Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 1: General principles for selection of cracking-resistant materials |
| ISO 13628-4:2010 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 4: Subsea wellhead and tree equipment |
| API TR 17TR1 : 2003 | EVALUATION STANDARD FOR INTERNAL PRESSURE SHEATH POLYMERS FOR HIGH TEMPERATURE FLEXIBLE PIPES |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ISO 36:2017 | Rubber, vulcanized or thermoplastic Determination of adhesion to textile fabrics |
| ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 13628-10:2005 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 10: Specification for bonded flexible pipe |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.