I.S. EN ISO 1133:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - DETERMINATION OF THE MELT-MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
Hardcopy , PDF
English
01-01-2005
12-20-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
5.1 Extrusion plastometer
5.2 Accessory equipment
6 Test sample
6.1 Sample form
6.2 Conditioning
7 Temperature-calibration, cleaning and maintenance of
the apparatus
7.1 Calibration of the temperature-control system
7.2 Cleaning the apparatus
8 Procedure A: mass-measurement method
8.1 Selection of temperature and load
8.2 Cleaning
8.3 Selection of sample mass and charging cylinder
8.4 Measurements
8.5 Expression of results
9 Procedure B: displacement-measurement method
9.1 Selection of temperature and load
9.2 Minimum piston displacement distance
9.3 Timer
9.4 Preparation for the test
9.5 Measurements
9.6 Expression of results
10 Flow rate ratio (FRR)
11 Precision
12 Test report
Annex A (normative) Test conditions for MFR and MVR
determinations
Annex B (informative) Conditions specified in International
Standards for determination of the melt flow rate
of thermoplastic materials
Provides two procedures for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastic materials under specified conditions of temperature and load.
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 1133:2005 | Identical |
| EN ISO 1133:2005 | Identical |
| NS EN ISO 1133 : 2ED 2005 | Identical |
| NBN EN ISO 1133 : 2005 COR 2006 | Identical |
| NEN EN ISO 1133 : 2005 | Identical |
| DIN EN ISO 1133:2005-09 | Identical |
| NF EN ISO 1133 : 2005 | Identical |
| BS EN ISO 1133:2005 | Identical |
| UNE-EN ISO 1133:2006 | Identical |
| DIN EN ISO 1133:2000-02 | Identical |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| ISO 1622-2:1995 | Plastics — Polystyrene (PS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 7391-2:2006 | Plastics — Polycarbonate (PC) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 2897-2:2003 | Plastics — Impact-resistant polystyrene (PS-I) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 15494:2015 | Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) — Metric series for specifications for components and the system |
| ISO 1873-2:2007 | Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 8986-2:2009 | Plastics — Polybutene-1 (PB-1) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 4894-2:1995 | Plastics — Styrene/acrylonitrile (SAN) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 2580-2:2003 | Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings |
| ISO 1872-2:2007 | Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 10366-2:2003 | Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 4613-2:1995 | Plastics — Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 8257-2:2001 | Plastics — Poly(methyl methacrylate) (PMMA) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 6402-2:2003 | Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 9988-2:2006 | Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.