I.S. EN ISO 10423:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - DRILLING AND PRODUCTION EQUIPMENT - WELLHEAD AND CHRISTMAS TREE EQUIPMENT
Hardcopy , PDF
04-15-2022
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 Design and performance - General requirements
5 Materials - General requirements
6 Welding - General requirements
7 Quality control
8 Equipment marking
9 Storing and shipping
10 Equipment-specific requirements
11 Repair and remanufacture
Annex A (informative) - Purchasing guidelines
Annex B (informative) - USC unit tables and data for this
International Standard
Annex C (informative) - Method of calculating stud bolt lengths
for type 6B and 6BX flanges
Annex D (informative) - Recommended flange bolt torque
Annex E (informative) - Recommended weld preparation design
dimensions
Annex F (informative) - Design validation procedures
Annex G (informative) - Design and rating of equipment for
use at elevated temperatures
Annex H (normative) - Design and manufacture of surface
wellhead running, retrieving and testing
tools, clean-out tools and wear bushings
Annex I (normative) - Design validation procedures for surface
safety valves and underwater safety valves
Annex J (normative) - Repair and remanufacture requirements
Annex K (informative) - Recommended specifications for top
connectors for christmas trees
Annex L (normative) - Specifications for valve-removal
preparations, valve-removal plugs and
handling tools
Annex M (informative) - Qualification of heat-treating
equipment
Annex N (informative) - List of tables and list of figures
Bibliography
Describes requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, purchasing, repair and remanufacture of wellhead and christmas tree equipment for use in the petroleum and natural gas industries.
| DocumentType |
Standard
|
| Pages |
446
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN ISO 10423 : 2010 | Identical |
| NF EN ISO 10423 : 2013 | Identical |
| NS EN ISO 10423 : 2009 | Identical |
| ISO 10423:2009 | Identical |
| EN ISO 10423:2009 | Identical |
| SN EN ISO 10423:2010 | Identical |
| BS EN ISO 10423:2001 | Identical |
| NEN EN ISO 10423 : 2010 | Identical |
| UNI EN ISO 10423 : 2012 | Identical |
| DIN EN ISO 10423:2010-05 | Identical |
| BS EN ISO 10423:2009 | Identical |
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| API 5CT : 2012 | CASING AND TUBING |
| API TR 6AF2 : 2013 | TECHNICAL REPORT ON CAPABILITIES OF API INTEGRAL FLANGES UNDER COMBINATION OF LOADING - PHASE 2 |
| API TR 6AF1 : 1998 | TECHNICAL REPORT ON TEMPERATURE DERATING ON API FLANGES UNDER COMBINATION OF LOADING |
| ISO 13628-3:2000 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 3: Through flowline (TFL) systems |
| ASTM D 1414 : 2015 : REDLINE | Standard Test Methods for Rubber O-Rings |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| API 6A : 2010 | SPECIFICATION FOR WELLHEAD AND CHRISTMAS TREE EQUIPMENT |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
| SAE AS 568 : 2014 | AEROSPACE SIZE STANDARD FOR O-RINGS |
| API 6A718 : 2009 | NICKEL BASE ALLOY 718 (UNS N07718) FOR OIL AND GAS DRILLING AND PRODUCTION EQUIPMENT |
| ASTM E 10 : 2017-05 | TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| ASTM E 110 : 2014 : REDLINE | Standard Test Method for Rockwell and Brinell Hardness of Metallic Materials by Portable Hardness Testers |
| API 14D : 1994 | SPECIFICATION FOR WELLHEAD SURFACE SAFETY VALVES AND UNDERWATER SAFETY VALVES FOR OFFSHORE SERVICE |
| ISO 31-0:1992 | Quantities and units Part 0: General principles |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ISO 13678:2010 | Petroleum and natural gas industries Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements |
| API 7 : 2001 | SPECIFICATION FOR ROTARY DRILL STEM ELEMENTS |
| ASTM A 453/A453M : 2017 : REDLINE | Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels |
| ISO 13533:2001 | Petroleum and natural gas industries — Drilling and production equipment — Drill-through equipment |
| ISO 13628-4:2010 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 4: Subsea wellhead and tree equipment |
| ASME B16.34 : 2017 | VALVES - FLANGED, THREADED, AND WELDING END |
| ASME PV CODE 5 : 2017 | BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION |
| MSS SP 55 : 2011 | QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES |
| ASME B18.2.2 : 2015 | NUTS FOR GENERAL APPLICATIONS: MACHINE SCREW NUTS, HEX, SQUARE, HEX FLANGE, AND COUPLING NUTS (INCH SERIES) |
| ISO 10424-1:2004 | Petroleum and natural gas industries — Rotary drilling equipment — Part 1: Rotary drill stem elements |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| API 6AF : 2008 | TECHNICAL REPORT ON CAPABILITIES OF API FLANGES UNDER COMBINATIONS OF LOAD |
| API 6AV1 : 2013 | SPECIFICATION FOR VALIDATION OF WELLHEAD SURFACE SAFETY VALVES AND UNDERWATER SAFETY VALVES FOR OFFSHORE SERVICE |
| SAE AMS H 6875 : 2010 | HEAT TREATMENT OF STEEL RAW MATERIALS |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| ISO 18265:2013 | Metallic materials — Conversion of hardness values |
| ISO 11960:2014 | Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells |
| ISO 10414-1:2008 | Petroleum and natural gas industries — Field testing of drilling fluids — Part 1: Water-based fluids |
| ASTM D 1418 : 2017 : REDLINE | Standard Practice for Rubber and Rubber Latices—Nomenclature |
| ASTM E 92 : 2017 : REDLINE | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.